• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제24회 춘계학술대회논문집
• /
• pp.368-373
• /
• 2005

효과적인 초음속 연소를 수행하기 위해 연료와 공기의 빠른 혼합을 이룰 수 있는 연료 분사 기술이 요구된다. 본 수치적 연구의 목적은 초음속 유동장내에서 공동 주위 연료분사 위치에 따른 연료/공기 혼합 및 연소 현상을 살펴보고자 한다. 연료 분사 위치는 연소기내에서 영향을 미치는 공동의 길이-깊이비를 변화시킨다. 따라서 같은 형상의 공동이라 하더라도 공동 주위 유동 특성이 달라지므로 연소기 내부의 연료/공기 혼합과 연소 현상에 영향을 끼치게 된다.

• 한국자동차공학회논문집
• /
• 제9권5호
• /
• pp.75-81
• /
• 2001

This paper presents the atomization characteristics of single hole injector in the direct injection type diesel engine. The spray characteristics of fuel injector such as the droplet size and velocity were measured by phase Doppler particle analyzer. In this paper, the atomization characteristics of fuel spray are investigated for the experimental analysis of the measuring data by the results of mean diameter and mean velocity of droplet. The effect of fuel injection pressure on the droplet size shows that the higher injection pressure results in the decrease of mean droplet diameter in the fuel spray. The minimum size of fuel spray droplet appears on the location of 40mm axial distance from nozzle exit of diesel injector. Based on the experimental results, the correlation between the droplet diameter and mean velocity of the diesel spray due to the change of axial and radial distance from the nozzle tip were investigated.

• 한국분무공학회지
• /
• 제4권2호
• /
• pp.33-39
• /
• 1999

This paper presents the spray atomization characteristics of the high-pressure gasoline injector for the direct-injection gasoline engine. The gasoline sprays of the injector were minted into a pressurized spray chamber with a optical access at various ambient pressures. The atomization characteristics of fuel spray such as mean diameter, mean velocity of droplet were measured by the phase Doppler particle analyzer system. In order to investigate the effect of fuel injection pressure on the quantitative characteristics of spray, the global visualization and experiment of particle measurement in the fuel spray were investigated at 3, 5 and 7 MPa of injection pressure under different ambient pressure in the spray chamber. Based on the results of this work, the fuel injection pressure of fuel injector in gasoline direct-injection engine have influence upon distribution of the mean velocity and droplet size of fuel spray. Also, the influence of injection pressure on the velocity distribution at various measuring location were investigated.

• 한국자동차공학회논문집
• /
• 제7권8호
• /
• pp.1-6
• /
• 1999

An experimental study was carried out to investigate the global spray behavior and spray characteristics of high-pressure fuel injector in the direct-injection goasoline enginet. The atomization characteristics of fuel spary such as mean droplet size, mean velocity , and velocity distribution were measured by the phase Doppler particle analyzer. The spray tip penetration and spray width were investigated by the result fo visualizaiton experiment. The quantitiative spary characteristics of injector spray were measured under various sparay conditions and ambient pressures. The results of experiment show that the increase in ambient pressure have influence on the spray tip penetration and spray development process. Also, the influence of injection pressure and measuring location on the mean velocity and droplet size distribution were discussed.

• 항공우주시스템공학회지
• /
• 제2권4호
• /
• pp.1-6
• /
• 2008

In generally, the regression rate was expressed with average value and oxidizer mass flux in hybrid propulsion system. This can not represent the local value of regression rate along with oxidizer flow direction. In this study, experimental studies were performed with Separation method and Cutting method for measure local regression rate. In axial injection, the local regression rate decreases rapidly with axial location near entrance and increases with axial direction from the leading edge and the empirical formula for local regression rate with function of oxidizer mass flux and location was derived. Swirl injection regression rate has higher value at the leading edge of the fuel and comparatively uniform regression rate at the downstream. Overall regression rate of swirl injection is higher increased about 54 % than regression rate of axial injection.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2005년도 제31회 KOSCO SYMPOSIUM 논문집
• /
• pp.255-260
• /
• 2005

To achieve efficient combustion within a manageable length, a successful fuel injection scheme must provide rapid mixing between the fuel and airstreams. The aim of the present numerical research is to investigate the flame holding and combustion enhancement. Additional fuel into the cavity prevents shear flow impingement on the trailing edge of the cavity. The high temperature freestream flow mixes with the cold hydrogen fuel that is injected into the cavity and raises the fuel temperature remarkably and become to start combustion. The high pressure in the cavity due to the cavity structure and combustion leads the hydrogen fuel to upstream. The shock in the cavity to be generated by the fuel injection joins together and reflects off the ceiling wall. This makes high pressure and low mach number region and makes a small recirculation in this region. This high stagnation temperature is nearly recovered in the shear layer in front of the cavity and leads to start combustion. In the downstream of the cavity, the wall pressure drops significantly. This means that the combustion phenomenon is diminished. Because fuel lumps at the trailing edge of the cavity then it spreads after the cavity so, in this region there is a strong expansion.

• 한국추진공학회지
• /
• 제3권2호
• /
• pp.18-24
• /
• 1999

액체 램제트 연소기는 흡입공기와 분무, 혼합 그리고 이에 따른 연소 등 일련의 과정에 따라 다수의 복잡한 현상들이 상호 밀접하게 관련되어 있으며, 이러한 반응 및 비반응 유동 특성을 파악하기 위해서 2차원 및 3차원 연소기 형상에 대해서 수치적 실험을 수행하였다 격자구성은 연소기에 공기를 공급하고 연료를 분무하는 공기 유입관 영역과 연소실 영역, 그리고 출구 대기 영역으로 나누어 격자를 생성시켰다. 비반응 유동해석을 통해서 연소실내의 선회영역 유동특성은 2차원과 3차원이 크게 차이가 남을 알 수 있었다. 반응 유동 해석에서는 분무 모델의 적용 유무에 따라 연소 형태가 크게 변화하였다. 연료의 분사위치를 유입관의 위쪽에 준 경우와 아래쪽에 준 두 가지 경우를 비교하였으며, 유입관의 아래쪽에 연료의 분사위치를 준 경우가 연소의 안정화에 필요한 재순환 영역으로의 연료의 유입이 잘 되어 유입관 위쪽에 연료를 분사시키는 것보다 좋은 분사위치임을 알 수 있었다.

• Journal of Mechanical Science and Technology
• /
• 제16권7호
• /
• pp.950-958
• /
• 2002

The combustion characteristics of a low NOx burner using reburning technology have been experimentally studied. The return burner usually has three distinct reaction zones which include the primary combustion zone, the reburn zone and the burnout zone by provided secondary air. NOx is mainly produced in a primary combustion zone and a certain portion of NOx can be converted to nitrogen in the rebury zone. In the burnout zone, the unburned mixtures are completely oxidated by supplying secondary air. Liquefied Petroleum Gas (LPG) was used as main and reburn fuels. The experimental parameters investigated involve the main/reburn fuel ratio, the primary/secondary air ratio, and the injection location of rebury fuel and secondary air. When the amount of return fuel reaches to the 20-30% of the total fuel used, the overall NO reduction of 50% is achieved. The secondary air is injected by two different ways including vertical and parallel injection. The injector of secondary air is located at the downstream region of furnace for a vertical-injection mode, which is also placed at the inlet primary-air injection region for a parallel-injection mode. In case of the vertical injection of the secondary air flow, the NOx formation of stoichiometric condition at a primary combustion zone is nearly independent of the rebury conditions (locations, fuel/air ratios) while the NOx emission of the fuel-lean condition is considerably influenced by the reburn conditions. In case of the parallel injection of the secondary air, the NOx emission is sensitive to the air ratio rather than the fuel ratio and the reburning process often coupled with the multiple air-staging and fuel-staging combustion processes.

• 한국항공우주학회지
• /
• 제33권2호
• /
• pp.92-97
• /
• 2005

추력 10 tonf 액체로켓용 가스발생기를 최적설계하고 설계 검증을 위한 연소 실험을 실시하였다. 연소실에 사용된 인젝터는 F-O-F triplet 충돌형 인젝터 이었으며 추진제는 kerosene/LOX을 사용하였다. 측정된 연소 온도와 압력은 최적 설계에서 얻은 설계 값과 매우 유사한 값을 나타내어 최적설계가 적절히 이루어 졌음을 확인하였다. 그리고 난류 고리를 설치하여 연소가스의 혼합을 촉진시킨 결과, 연소실 압력은 3.2% 감소에 그친 반면, 반경 방향 온도분포는 편차가 15K 이하로 줄어들어 우수한 온도 분포 특성을 나타내었다. 또한 후단부에서 축 방향 온도분포를 측정한 결과 최적 설계로부터 얻은 가스발생기 길이를 10% 줄일 수 있음을 발견하였으며 난류고리의 위치를 적절히 조절한다면 그 이상의 길이 감소도 가능한 것으로 판단하였다.