• 한국추진공학회지
• /
• 제8권4호
• /
• pp.76-83
• /
• 2004

CRW Tyre UAV 추진시스템은 수직으로 이착륙이 가능하고 고정익으로 고속 전진 비행이 가능한 개념으로 설계되었다. 이를 위해 추진시스템은 이착륙 시에는 로터를 구동시켜 수직으로 비행하고 고속 비행 시에는 로터를 정지시켜 날개로 사용하고 가스발생기에서 생성된 가스를 주 노즐로 분사하여 본래의 제트엔진으로 사용한다. ICV방법과 SIMULINK를 이용하여 천이 성능 해석을 수행하였다. 연료유량은 터빈 입구온도의 스텝과 과온 현상을 피하기 위해 램프 증가를 하였고 이에 따른 추력의 변화와 터빈 입구온도의 변화를 살펴보았다.

• 한국추진공학회지
• /
• 제5권4호
• /
• pp.83-93
• /
• 2001

본 연구에서는 화염의 안정화를 위하여 사용되는 선회류 발생 장치의 베인에 작은 스케일의 난류를 발생시킬 수 있는 난류 발생기를 장착하여 연료와 흡입공기의 혼합을 촉진시키고, 연소와 온도의 균일도를 향상시키기 의한 실험적 검토를 행하였다. 실험에서는 내부 혼합용 이유체 분사노즐 사용하여 등유를 분사시킨 후 연료와 흡입공기의 혼합과 연소 현상을 관측하였다. 난류발생기는 베인 각도에 따른 베인과 베인 사이의 각 단면의 면적을 계산하여 그 유로단면의 면적에 대한 비율로서 난류발생기의 면적을 결정하여 선회기를 통과하는 유로 단면적의 각각 0%, 3%, 7%, 12%에 해당하는 면적의 난류 발생기를 제작하여 선회기 출구 베인의 끝단에 설치하였다. 실용 연소기의 구조를 어느 정도 단순화한 환형 연소기에서의 농도분포, 화염구조 및 온도분포를 조사하여 효과적인 연소기내의 연소제어에 사용하고자 한다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.499-505
• /
• 2004

A Propulsion System of the CRW(Canard Rotor Wing) type UAV(Unmanned Aerial Vehicle) was composed of the turbojet engine to generate the propulsive exhaust gas, and the duct system including straight bent ducts, tip-jet nozzles, a master valve and a variable main nozzle for three flight modes such as lift/landing mode, low speed transition flight mode and high speed forward flight mode. In this study, in order to operate safely the propulsion system, the dynamic Performance behavior of the system was modeled and simulated using the SIMULIN $K^{ }$, which is the user-friendly GUI type dynamic analysis tool provided by MATLA $B^{ }$. In the transient performance model, the inter-component volume model was used. The performance analysis using the developed models was performed at various flight condition, valve angle positions and fuel flow schedules, and these results could set the safe flight mode transition region to satisfy the inlet temperature overshoot limitation as well as the compressor surge margin. Performance analysis results using the SIMULIN $K^{ }$ performance program were compared with them using the commercial program GSP.m GSP.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.466-471
• /
• 2004

In gas turbines, excess air for combustion is available and therefore lean premixed combustion is the most promising approach to the significant reduction of thermal NOx emissions. At lean conditions, however, flame stability is inherently worse and hence combustion tends to be incomplete. Efforts have been devoted toward extending the operating range of complete combustion at leaner conditions. One of them is the lean-lean two-stage combustion where lean to ultra-lean secondary mixtures are mixed with the hot burned gas from the primary stage. Conventional flame combustion or flameless reaction are initiated depending on the conditions of the secondary zone. In the first part of the present study, the effects of fuel injection on the emissions and flame stability were investigated for a single tubular flame, In the second part, the emissions and flame stability were studied for a two-stage combustor with secondary mixture injected through the tangential slots on a cylindrical combustor wall. The effects of the ratio of air flow rates to the primary and secondary zones on the emissions and combustion characteristics were investigate.

• 한국추진공학회지
• /
• 제12권4호
• /
• pp.63-77
• /
• 2008

본 논문에서는 가스터빈에서의 연소불안정 현상과 그 메커니즘에 대해 살펴보았다. 연소불안정 연구를 위한 접근 방법이 논의되었고 전 세계 연소불안정 관련 연구그룹들의 최신 연구동향이 소개되었다. 현재까지도 연소불안정현상은 기관의 성능, 내구성, 작동 등에 영향을 미치는 중요한 문제 중의 하나이다. 덧붙여 가스터빈기관에서 연소불안정 현상은 공기 또는 연료의 섭동과 열방출율 사이의 상호 중첩된 결과로 알려져 있으며, 이는 NOx 감소 전략과도 관련이 있다. 따라서 연소불안정 연구에 대한 현황을 이해하기 위하여 가스터빈에서의 연소불안정 현상에 대하여 정리하여 보았다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.1084-1087
• /
• 2017

액체로켓에서 엔진의 시동은 산화제와 연료를 연소기에 매우 짧은 시간의 차를 두고 주입하여야 하며, 이때 주입시간의 간격, 점화기 작동 지연 등은 방대한 량의 추진제 혼합물에 에너지를 인가함으로서 대형 폭발로 이어질 수 있는 상황이 된다. 그러므로 각 추진제의 천이특성과 연소기 또는 가스발생기의 유입 시점을 측정하는 것은 매우 중요하며, 상대적으로 느린 응답 특성을 갖는 정압으로는 유입 시점을 관측하기에는 어려움이 많으므로 추진제 유로를 따라 동압을 측정하여 보다 정확한 유입시점을 찾을 수 있었다.

• 한국안전학회지
• /
• 제25권2호
• /
• pp.12-17
• /
• 2010

Numerical simulations were performed for the prediction of the flame structure during the interaction between hydrogen and hydrocarbon flames. A counterflow flow geometry was introduced to establish the interacting two flames. Methane was used as a representative hydrocarbon fuel in this study. A well-known numerical code for the counterflow flame, OPPDIF, was used for the simulations. The detailed chemistry was adopted to predict the flame structure reasonably. The interaction of two one-dimensional premixed flames established in counterflow burner was investigated with the global strain rate and velocity ratio. It was found that the maximum temperature located near the methane flame surface while the heat release rate of methane was lower than hydrogen flame. The flame thickness become narrow with increasing the velocity ratio while the global strain rate was fixed. The local strain rate and heat release rate at the methane flame surface were correlated with the global strain rate, while those at the hydrogen flame were not correlated with the global strain rate. However, the maximum temperature of the interacting flames was correlated with the global strain rate.

• 한국연소학회지
• /
• 제19권3호
• /
• pp.18-25
• /
• 2014

Bottom ash from a coal-fired power plant is usually landfilled to a nearby site, which causes a growing environmental concern and increased operating costs. One way of recycling the bottom ash is to produce light-weight aggregate (LWA) using a rotary kiln. This study investigated the temperature profiles of raw LWA particles in a rotary kiln to identify the range of operating conditions appropriate for ideal bloating. For this purpose, a new simulation method was developed to integrate a 1-dimensional model for the bed of LWA particles and the computational fluid dynamics (CFD) for the fuel combustion and gas flow. The temperature of LWA particles was found very sensitive to the changes in the air preheating temperature and excess air ratio. Therefore, an accurate control of the operation parameters was essential to achieve the bloating of LWA particles without excessive sintering or melting.

• 한국항공운항학회지
• /
• 제27권4호
• /
• pp.9-20
• /
• 2019

A military aircraft generally includes external stores such as fuel tanks or external arming, depending on the purpose of the operation. When a store is dropped from a military aircraft at high subsonic, transonic, or supersonic speeds, the aerodynamic forces and moments acting on the store can be sufficient to send the store back into contact with the aircraft. This can cause damage to the aircraft and endanger the life of the crew. In this study, time accurate computational fluid dynamics (CFD) with dynamic moving grid (moving and deformable mesh, MDM) technique has been used to accurately calculate store trajectories. For the verification of the present numerical approach, a wind tunnel test model for the wing-pylon-finned store configuration has been considered and analyzed. The comparison results for the ejected store trajectories between the present numerical analysis and the wind tunnel test data at the Mach number of 0.95 and 1.2 are presented. It is also importantly shown that the numerical parameter of MDM technique gives significant effect for the calculated store trajectory in the low-supersonic flow such as Mach 1.2.

• Journal of Biosystems Engineering
• /
• 제10권2호
• /
• pp.19-26
• /
• 1985

This study was carried out to develop a versatile data acquisition/processing system for overall tractor performance utilizing a NEC PC-8001 microcomputer. The data acquisition system measures drawbar pull and power, wheel torque and axle power, ground speed, wheel slip, fuel flow, and engine speed. The system stores hexadecimal data for these variables in memory. Upon completion of each test run, all hexadecimal data stored in memory are recorded on floppy disc. The data processing system reads in the data collected on floppy disc and interprete them using several graphical and statistical techniques. The system uses the same microcomputer and a dot-matrix printer. The data acquisition system has been installed on a GOLDSTAR 500 tractor (2WD, 50 ps). A field study has shown that tractor performance data can be quickly and easily collected. It also appeared that the data processing system can be used to efficiently analyze the collected data. The data acquisition system has some troublesome in mounting and handling on tractor since it uses a general-purpose computer consisting of several components.