• 대한한의진단학회지
• /
• 제15권2호
• /
• pp.203-214
• /
• 2011

Objectives: The objective of the current study is to determine whether an ultrasound device system is adequate for measuring distance from the abdominal surface of Sangwan (CV13) to peritoneum in front of anterior surface of liver. Methods: We recruited 3 healthy young male subjects and 2 sonographers. The each sonographer measured vertical shortest distance from the abdominal surface of Sangwan (CV13) to peritoneum in front of anterior surface of liver with a ultrasound device with three methods of 3.5 MHz convex probe and gel, 9 MHz linear probe and gel, and 9 MHz linear probe and solid gel pad, three times in random order. Because the total variation could be divided into repeatability, reproducibility and subject-to-subject variation in Gage R&R method, we compared the sources of variation associated with the measurement system with an analysis of variance model. Results & Conclusions: Number of distinct categories is calculated on the basis of standard deviation of subject-to-subject divided by standard deviation of total Gage R&R. If the number of categories is five or more, the measurement system may be acceptable for the analysis of the process. The number of distinct categories of the ultrasound device system for measuring distance from the abdominal surface of Sangwan (CV13) to peritoneum in front of anterior surface of liver were 9.20 (9 MHz linear probe and gel), 14.70 (9 MHz linear probe and solid gel pad). So we concluded that repeatabilities and reproducibilities of the ultrasound device system for measuring distance from the abdominal surface of Sangwan (CV13) to peritoneum in front of anterior surface of liver with the methods of 9 MHz linear probe and gel, and 9 MHz linear probe and solid gel pad were acceptable.

• 한국전자파학회논문지
• /
• 제23권6호
• /
• pp.723-730
• /
• 2012

위성 SAR(Synthetic Aperture Radar)를 정확하게 보정하기 위해서는 검보정에 사용되는 삼각 전파 반사기(Trihedral Corner Reflector: TCR)의 RCS(Radar Cross Section)를 정확하게 계산해야 한다. 본 연구에서는 TCR이 설치된 지표면이 TCR의 RCS 값에 얼마나 영향을 미치는지를 알아보기 위해서 지표면에서의 반사파와 TCR 모서리에서의 회절파를 이론적으로 계산하여 검보정 사이트의 지표면 상태에 따른 RCS 변화를 분석하였다. 지표면 반사파를 구하기 위해 지표면에 대한 PO 반사 계수를 이용하였으며, PO 반사 계수는 지표면 상태 변수인 거칠기와 유전율에 대한 함수이다. 중심 주파수 9.65 GHz에서 지표면 위에 설치된 $10{\lambda}$ 크기 TCR의 RCS 값은 공기 중의 TCR에 비해 0.46 dB 변화가 발생하였고, 이 변화는 지표면의 상태 및 TCR 크기에 따라 크게는 1.55 dB정도의 차이가 날 수 있다. 지표면 영향에 따른 TCR의 RCS 값은 지표면의 거칠기가 작고 유전율이 클수록 크며, 중심 주파수가 낮고 TCR의 크기가 작을수록 크게 발생하였다.

• 대한기계학회논문집A
• /
• 제36권10호
• /
• pp.1155-1162
• /
• 2012

알루미늄 크래쉬 박스는 저속충돌조건에서 프론트 사이드 멤버를 변형을 방지하기 위한 부품이다. 본 연구에서는 저속충돌조건에서 비드형상이 알루미늄 크래쉬 박스의 충돌성능에 미치는 영향을 분석하였다. Edge concave, surface convex 와 surface concave 타입의 비드형상들에 대한 충돌해석 및 실험을 수행하여 비드가 없는 normal 타입의 알루미늄 크래쉬 박스의 충돌성능과 비교분석하였다. 충돌성능은 저속충돌조건에서 크래쉬 박스의 초기 최대하중 및 충돌에너지 흡수능으로 평가하였다. 이를 검증하기 위해 알루미늄 크래쉬 박스와 결합된 프론트 사이드 멤버에 대해 저속충돌실험 수행하고, 이를 분석하였다. Surface concave 타입의 비드가 삽입된 알루미늄 크래쉬 박스 경우, 프론트 사이드 멤버의 변형을 방지할 수 있음을 확인하였다.

• 대한기계학회논문집A
• /
• 제24권1호
• /
• pp.144-155
• /
• 2000

초록 The validity, of a single parameter such as stress intensity, factor K or J-integral in traditional fracture mechanics depends strongly on the geometry, and loading condition. Therefore the second parameter like T-stress measuring the stress constraint is additionally needed to characterize the general crack-tip fields. While many, research works have been done to verify, the J-T description of elastic-plastic crack-tip stress fields in plane strain specimens, limited works (especially. for bimaterials) have been performed to describe the structural surface crack-front stress fields with the two parameters. On this background, via detailed three dimensional finite element analyses for surface-cracked plates and straight pipes of homogeneous materials and bimaterials under various loadings, we investigate the extended validity or limitation of the two parameter approach. We here first develop a full 3D mesh generating program for semi-elliptical surface cracks, and calculate elastic T-stress from the obtained finite element stress field. Comparing the J-T predictions to the elastic-plastic stresses from 3D finite element analyses. we then confirm the extended validity of fracture mechanics methodology based on the J-T two parameters in characterizing the surface crack-front fields of welded plates and pipes under various loadings.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 추계학술대회 논문집
• /
• pp.264-267
• /
• 2007

It is important to reduce optical losses from front surface reflection to improve the efficiency of crystalline silicon solar cells. Surface texturing by isotropic etching with acid solution based on HF and $HNO_3$ is one of the promising methods that can reduce surface reflectance. Anisotropic texturing with alkali solution is not suitable for multicrystalline silicon wafers because of its various grain orientations. In this paper, we textured multicrystalline silicon wafers by simple wet chemical etching using acid solution to reduce front surface reflectance. After that, surface morphology of textured wafer was observed by Scanning Electron Microscope(SEM) and Atomic Force Microscope(AFM), surface reflectance was measured in wavelength from 400nm to 1000nm. We obtained 29.29% surface reflectance by isotropic texturing with acid solution in wavelength from 400nm to 1000nm for fabrication of multicrystalline silicon solar cells.

• 한국CDE학회논문집
• /
• 제11권2호
• /
• pp.138-147
• /
• 2006

A systematic approach to tetrahedral element or mesh generation, based on an advancing-front method and an optimal triangular mesh generation technique on the surface, is presented in this paper. The possible internal nodes are obtained by the octree-decomposition scheme. The initial tetrahedral mesh system is constructed by the advancing-front method and then it is improved by the quality improvement processes including mesh swapping and nodal smoothing. The approach is evaluated by investigating the normalized length, the normalized volume, the dihedral angle and the normalized quality

• Journal of electromagnetic engineering and science
• /
• 제12권4호
• /
• pp.247-253
• /
• 2012

This study presents a new, simple method for improving the front-to-back (F/B) ratio of a microstrip patch antenna. The back radiation of the microstrip patch antenna is reduced by removing some metallic parts around the ground plane and placing a new soft-surface configuration, consisting of an array of stand-up split-ring resonators on a bare dielectric substrate near the two ground plane edges. Compared to the F/B ratio of a conventional microstrip patch antenna with a full ground plane of the same size, our proposed microstrip patch antenna experimentally achieves an improved F/B ratio of 9.6 dB.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.85-85
• /
• 2012

For effective light harvesting, a design weighting should be implemented in a front geometry, in which the incident light transmits from a surface into a light-active layer. We designed a three-dimensionally patterned transparent conductor layer for effective light management. A transparent conductive oxide (TCO) film was formed as three-dimensional structures. This efficiently drives the incident light at the front surface into a Si absorber to yield a reduction in reflection and an enhancement of current. This indicates that an optimum architecture for a front TCO surface will provide an effective way for light management in solar cells.

• Journal of the Optical Society of Korea
• /
• 제18권5호
• /
• pp.495-499
• /
• 2014

In this paper, a method is proposed for simultaneously measuring the front and back surface profiles of transparent micro-optical components. The proposed method combines a dual-wavelength digital holographic microscope with liquids to record holograms at different wavelengths, and then numerically reconstructs the three-dimensional phase information to image the front and back sides of the sample. A theoretical model is proposed to determine the surface information, and imaging of an achromatic lens is demonstrated experimentally. Unlike conventional interferometry, our proposed method supports nondestructive measurement and direct observation of both front and back profiles of micro-optical elements.

• 소성∙가공
• /
• 제11권8호
• /
• pp.691-700
• /
• 2002

Injection molded plastic parts have many surface detects: weld line, sink mark, flow mark, gloss, shading, scratching, and so on. Because these surface faults have not been accepted esthetically, plastic parts are Produced through painting or texturing. The purpose of this paper is to develop a paintless molded part of TV Mask Front by flow control method and gas-assisted injection molding. In order to minimize defects from injection molding, this study was carried out using computer aided injection mold filling simulations using MF/FLOW and MF/GAS. Based on these numerical results, we developed FR(Flame Retardant) HIPS and established guidelines of part design, mold design, and Processing conditions. We have achieved of cost sayings, improvement of productivity, and utilization of recycling by eliminating surface defects and painting process.