• 융합신호처리학회논문지
• /
• 제13권4호
• /
• pp.220-232
• /
• 2012

본 논문에서는 VCS의 지연추적과 프린지 회전 모듈의 문제로 인한 상관결과에 대해 고찰한다. VCS는 FX 형식의 상관기로서 도플러 효과에 의한 전체로부터 도달하는 신호의 지연시간과 프린지 위상을 보정하기 위해 지연추적과 프린지 회전 모듈을 채용하고 있다. 관측데이터는 상관기에서 지연추적과 프린지 회전을 통하여 위상정보도 함께 보정되는데, AIPS에서 상관기보다 장시간의 상관적분을 수행함에 따라 위상이 안정되지 않은 것을 확인하였다. 그리고 상관결과의 해석에서 Delay 값이 정상보다 수십 nsec 정도 오차가 발생하였다. 또한 프린지 회전모듈에서 프린지 초기위상을 결정하지 않아서 상관결과의 위상이 FFT segment 단위로 연결되지 않는 것도 확인하였다. 본 논문에서는 이러한 문제들을 해결하기 위해 지연추적 모듈과 프린지 회전 모듈의 경우 위상보정을 담당하는 모듈의 부호가 반대로 동작하는 것과 관측데이터의 초기위상을 사용하도록 수정하였다. 그리고 프린지 회전 파라미터 계산모듈에 오류가 있는 것을 발견하여 VCS의 로직을 담당하는 프로그램을 개선하였다. 이상의 문제점들에 대해서 상관처리 실험을 통하여 본 논문에서 수정 제안한 알고리즘들이 데이터 해석결과에서 정확함을 확인하여, 개발한 VCS 하드웨어 상관기가 정상적으로 동작하는 것을 확인하였다.

• 한국전기전자재료학회논문지
• /
• 제17권3호
• /
• pp.305-310
• /
• 2004

We have studied the optimal phase retardation value of a homogeneously aligned liquid crystal (LC) driven by fringe-field when using the LC with positive dielectric anisotropy. In general, the transmittance of a homogeneous aligned LC cell under crossed polarizer is maximum when a twist angle of LC by in-plane rotation is 45$^{\circ}$ with polarizer and the cell retardation becomes λ/2. However, the device using the LC with positive dielectric anisotropy does not follow this since the degree of rotation of the LC is dependent on electrode position and in addition the LCs tilt up along the fringe-field. At the center of common and pixel electrode, the LC is most twisted around a middle position of a cell whereas at the edge position of pixel electrode, the LC is most twisted near bottom surface of a cell. Consequently, the optimal phase retardation of the device becomes much larger than λ/2 and the transmittance can be described using the combination of the in-plane switching and twisted nematic mode.

• 대한기계학회논문집
• /
• 제17권11호
• /
• pp.2723-2729
• /
• 1993

Moire principles are applied to the measurement of the spindle radial error motion. As opposed to conventional techniques, no master cylinder or ball is needed in the measurement so that the offset and out-of-roundness errors of the master can be inherently eliminated. Two periodic circular gratings are used, one is made on the spindle and the other is held stationary on the reference frame. When the two gratings are seen superimposed during spindle rotation, an interference fringe pattern is observed from which the information on the eccentricity between the two gratings can be extracted with high precision. The optical design and fringe analysis techniques of a prototype measurement system are described in detail with exemplary measurement results.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.320-325
• /
• 1999

An absolute type shaft encoder which utilized moire fringe will be presented in this paper. Linear moire fringe is commonly used to measure the displacement of the linear motion. However, an absolute encoder which measure the rotation angle of a shaft is operated usually with a code disk which the gray code pattern is printed on. Such encoder has inherently resolution limit because of the patterning mechanism and sensing mechanism. In order to measure the position of fringes which move as the code disk rotates, neural network was developed in this paper. Formerly fringe position is usually measured by a sophisticated software, which needs a little long calculation time. However, using neural network method can eliminate such calculation time, even though it needs learning job. The proposed method is verified through several experiments.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 추계학술대회 논문집 Vol.17
• /
• pp.567-570
• /
• 2004

We have designed a single gap transflective liquid crystal display (LCD) driven by a fringe electric field, in which the LCs are homogeneously aligned in the initial state. In the reflective and transmissive areas, the degrees of the rotation of the LC director are $22.5^{\circ}$ and $45^{\circ}$, respectively. Utilizing this mechanism and an in-cell retarder with a quarter-wave plate that is used below the LC layer, the transflective LCD using fringe-field switching (FFS) mode is realized.

• 대한치과교정학회지
• /
• 제22권3호
• /
• pp.531-556
• /
• 1992

The majority of the commonly used protraction headgears for the protraction of small and/or retropositioned maxilla not allow a change in the point of force application or direction of the force delivery to attain predictable results because of the position of the upper and lower lips to avoid discomfort to the patient. The purpose of this study was to investigate the initial reaction of maxillofacial complex according to the change of force variables such as direction and point of force application with designing an antenna type-modified protraction head gear. A macerated human skull with well aligned upper teeth was used to experimental model and the investigation was done by double exposure holographic interferometry. Fringe patterns of each protraction conditions were compared and analized. The results were as follows. (Frontal view) 1. The Counterclockwise rotation of the maxilla was showed by parallel protraction to occlusal plane and the fringe was decreased in number as higher point of force application. 2. Generally, the number of fringe was increased in 500gm of protraction force than in 300gm. 3. When apply the protraction force to the maxilla with rapid palatal expansion, the direction of fringe patterns was differed from the protraction without expansion. 4. In most of cases, the counterclockwise rotation was decreased in case of the direction of the force is $20^{\circ}$ downward to occlusal plane compared to the parallel direction. 5. At the point of force application is 15mm above and the direction of force is 20 downward to occlusal plane , the translation of the maxillary complex was showed. (Lateral view) 6. The direction of fringe patterns of the facial bones were differed each other by the sutures, and showed almost parallel when apply the 300gm and 500gm of protraction force. 7. In case of rapid palatal expansion with protraction of the maxilla, the fringe patterns between the maxillary area and the area from the posterior of the maxillary first molar to the pterygomaxillary fissure were differed. In case without rapid palatal expansion, the changes of direction and point of the force application did not affect to the direction and the number of the fringe patterns.

• 한국전기전자재료학회논문지
• /
• 제15권6호
• /
• pp.524-528
• /
• 2002

Conventional hybrid aligned nematic liquid crystal display (HAN-LCD) has several advantages on low operating voltage, fast response time and rubbing free on one substrate. We have fabricated a new hybrid aligned nematic display driven by fringe field. The new device exhibits much wider viewing: angle than that of the conventional HAN mode, owing to almost in-plane rotation of the LC director. Furthermore, we have developed the device that reveals more efficient electro-optic characteristics by placing common electrode on top and bottom substrates. In this paper, the electro-optic characteristics of the novel cell are investigated.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.312-313
• /
• 2008

A transflective liquid crystal displays associated with fringe field switching (FFS) mode of new concept is proposed. The device utilizes unique characteristic of the FFS mode in which the rotation angle of LC director is strongly dependent on electrode position in on state. We use the liquid crystal with negative dielectric anisotropy. Also we are look for optimized electrode size and the optimization of pixel electrode width and distance between them, the LC director could rotate about $22.5^{\circ}$ and $45^{\circ}$ depending on electrode positions. Consequently, we get high transmittance and high reflection on the optimized electrode condition. Respectively, a high image quality transflective display with single gap and single gamma characteristics realized.

• 대한치과교정학회지
• /
• 제18권2호
• /
• pp.367-385
• /
• 1988

In case of skeletal Class III malocclusion with underdeveloped maxilla, the extraoral orthopedic force for the stimulation of maxillary growth or anterior reposition of the maxilla has been used clinically for the improvement of facial skeletal relationship. The purpose of this investigation was to examine the initial reaction of maxillofacial complex to the maxillary protraction by using extraoral orthopedic force. The dried human skull was used and this investigation was done by means of double exposure holographic interferometry. The protraction forces placed on the canine or the first molar were parallel, $10^{\circ}$ downward, $20^{\circ}$ downward to the occlusal plane. Fringe pattern of each protraction condition was compared and analized. The results were as follows: 1. Each maxillofacial bone displaced saparately. 2. More displacement was shown at the area of the teeth and the alveolar bone. 3. A counterclockwise rotation of the maxilla wa decreased by downward protraction and especially 20 degree downward protraction from the canine showed least rotation. 4. On the zygomatic arch, outward bend was observed and this effect was decreased by downward protraction. 5. On the zygomatic bone, the counter clockwise rotation was increased by the downward protraction. 6. When maxillary expansion was applied at the same time, outward and upward displacement with counterclockwise rotation was observed on the maxilla. 7. The lateral pterygoid plate of sphenoid bone was affected by maxillary protraction.

• 한국산업융합학회 논문집
• /
• 제5권3호
• /
• pp.187-192
• /
• 2002

In-plane ESPI(Electronic Speckle Patten Interferometry)was devised to measure in~plane defamation and rotation of a specimen with laser in this study. The conventional measuring methods of surface deformations such as the strain gauge have many demerits because they are contact and point-to-point measuring ones. But that ESPI is noncontact, nondestructive and whole field measuring method can overcome previous disadvantages. We used ESPI which is sensitive to in-plane displacement for measuring in-plane deformations of a disk. First of all, the system calibration was done due to an in-plane rotation before getting deformations of a disk. Finally we showed good agreement between theexperiment results and those of the FEA(Finit Element Analysis).