• Transactions on Electrical and Electronic Materials
• /
• 제8권2호
• /
• pp.79-83
• /
• 2007

The implications of a theory of lubricated pad asperity wafer contact are traced through several fundamental areas of chemical-mechanical polishing. The hypothesized existence of a nanolubrication layer underlies a high accuracy model of polish rates. It also provides a quantitative explanation of a power law relationship between the coefficient of friction and a measure of pad surface flattening. The theory may further be useful for interpreting friction changes during polishing, and may explain why the coefficient of friction is sometimes observed to have a temperature or velocity dependence.

• 한국소음진동공학회논문집
• /
• 제22권8호
• /
• pp.736-741
• /
• 2012

Squeak noise is studied by using the pin-on-disk system with aluminum pin and steel disk. Noise induced by friction is measured with respect to the normal loads and sliding speeds. The negative slope of friction-velocity curve is seen when the squeak noise occurs. It is found that the normal load influences on the sound level of squeak noise. From the hammering test, the major frequency of the squeak noise is shown to correspond to one of system modes, which implies that squeak phenomenon arises from the unstable system modes. The result of FE analysis shows that the major squeak mode is the bending mode of the pin.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1652-1655
• /
• 2005

All teeth on the cycloidal plate gear exist in the contact motion with rollers and the forces are interacted between roller gears with cycloidal plate gears. So, the contact forces and friction forces must be required to improve the accuracy in design procedures of cycloidal speed reducers. This paper presents a force analysis considered the friction effect approach derived by static force equilibrium condition, geometrical adaptation, instant velocity center method and relative velocity method. Finally, the paper develops CAD-program for the construction of the design automation using the proposed method.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.1262-1265
• /
• 2004

A cycloidal speed reducer is a type of the speed reducers of machinery. The cycloidal speed reducer consists of two cycloidal plate gears, housing roller gear, input shaft, output pin and shaft, and eccentric bearings. Especially the cycloidal plate gear has the peculiar parts of the teeth, because of gearing with the housing roller gear that has the several rollers on the circular line. And then all teeth on the cycloidal plate gear can be designed to contact with the rollers on the housing roller gear at the same time. Therefore the cycloidal plate gear has always contact motion with rollers and the force is interacted between roller gear with cycloidal plate gear. Because the contact force and friction force must be required to improve the accuracy in design procedures of cycloidal speed reducers, this paper presents a force analysis considered friction effect approach derived by static force equilibrium condition, geometrical adaptation, instant velocity center method and relative velocity method.

• 한국자동차공학회논문집
• /
• 제2권2호
• /
• pp.1-11
• /
• 1994

The most commonplace of collisions that directly affect people is that of vehicles. Safety studies have noted a correlation between vehicle occupant injury severity and velocity changes. Methods for estimating collision velocity changes are discussed here. This topic is part of what is referred to as accident reconstruction. Only planar collisions are considered. When a vehicle collides with another, impact dynamics with friction should be considered. This paper presents a general analysis methodology of impact. must dynamics incorporating friction. The presence of friction between sliding contacts during the impact makes the problem difficult since the events such as reverse sliding or sticking, which may occur at different times throughout the impact, must be determined. This paper uses the results of RICSAC experiments for verifying the developed methodology. The analysis and experimental results agree well.

• Journal of applied mathematics & informatics
• /
• 제18권1_2호
• /
• pp.393-403
• /
• 2005

We study the isothermal flow of a dusty viscous incompressible conducting fluid between two types of boundary motions- oscillatory and non-oscillatory, under the influence of gravitational force. Within the frame work of some physically realistic approximations and suitable boundary conditions, closed form solutions were obtained for the velocity profiles and the skin friction of the particulate flow. These results show that for a constant pressure gradient, only the velocity profile of the fluid and the skin friction are unaffected by gravity, while magnetic field is seen to affect both the fluid, particle velocities and the skin friction. Thus, our results are extension of previous results in literature, and graphical demonstration of some these solutions have been presented.

• 대한기계학회논문집
• /
• 제19권10호
• /
• pp.2630-2636
• /
• 1995

A theoretically based prediction for the determination of the subchannel friction factor at low pitch to the rod diameter ratio (P/D < 1.2) in the bare rod bundle flow has been developed. The present model assumes the validity of the Law of Wall over the entire flow area. The algebraic form of the Law of the Wall is integrated over the entire flow area and the local friction velocity variation along the rod periphery is considered in this study. The present method is applied to the rod bundles with P/D < 1.2, and the prediction results show good agreement with the available experimental data.

• 한국소음진동공학회논문집
• /
• 제15권3호
• /
• pp.259-265
• /
• 2005

A two-degree-of-freedom out-of-plane model with contact stiffness is presented to describe dynamical interaction between the pad and disc of a disc brake system. It is assumed that the out-of-plane motion of the system depends on the friction force acting along the in-plane direction. Dynamic friction coefficient is modelled as a function of both in-plane relative velocity and out-of-plane normal force. When the friction coefficient depends only on the relative velocity, the contact stiffness has the role of negative stiffness. The results of stability analysis show that the stiffness of both pad and disc is equally important. Complex eigen value analysis is conducted for the case that the friction coefficient is also dependent on the normal force. The results further verify the importance of the stiffness. It has also been found that increasing the gradient of friction coefficient with respect to the normal force makes the system more unstable.

• Tribology and Lubricants
• /
• 제30권6호
• /
• pp.370-377
• /
• 2014

The basic elements in a rotary-type scroll compressor are two identical spiral scrolls containing refrigerant gas. The pressure variations in the compression pockets of a scroll compressor change the forces acting on the orbiting scroll, and these forces affect the dynamic behavior of the compression mechanism parts. To achieve high efficiency, using a self-sealing mechanism as a tip seal mechanism is very effective. Tip seals, which are placed on top of the scroll wraps, accomplish thrust sealing. This study calculates the friction force between the tip seal and the side plate of a scroll compressor using the numerical model considered in the Reynolds equation. The calculated friction force is verified by an experiment using a pin-on-disk apparatus. A hydraulic servo valve that controls the pressure of the oil hydraulic cylinder applies the normal load for the test, and a DC servo motor controls the sliding velocity of the disk. The friction force and normal load are measured by the force sensors attached to the supporting parts. The results show that the theoretical and experimental results are similar and that the friction is influenced by the viscosity of the oil and the sliding velocity of the scroll.

• 한국산학기술학회논문지
• /
• 제16권2호
• /
• pp.1533-1540
• /
• 2015

수공구조물 설계 또는 하상의 유동 특징을 나타내기 위해선 마찰속도 산정이 필수적이다. 하지만 기존의 개수로 내의 마찰속도 공식인 Log 방법이나 Power방법은 벽면 근처에서 경계층 조건 혹은 다양한 수리적 특성이 지속적으로 변화하기 때문에 마찰속도의 산정에 어려움이 있다. 따라서 본 연구에서는 매개변수를 최소화하고 오차를 줄일 수 있는 새로운 마찰속도 공식을 제안하였다. 제안한 공식에 대한 신뢰성과 정확성을 검증하기 위하여 엔트로피매개변수M을 각각의 수로마다 산정을 하여 Dr.Song이 산정한 3가지 방법(Clauser 방법, $\sqrt{gRI}$ 방법, 레이놀즈 응력법)으로 산정한 마찰속도와 비교하였다. 그 결과 가속부등류 조건의 경우 $R^2=0.9621$ 감속부등류 조건의 경우 $R^2=0.9274$ 등류흐름 조건의 경우 $R^2=0.8865$로 매우 높은 정확성으로 등류조건뿐만 아니라 부등류 조건에서도 거의 일치하였다.