본 연구에서 삼축압축시험기를 이용하여 낙동강유역 모래에 대한 상대밀도, 전단변형어속도, 구속압력의 변화에 의한 전단강도 특성을 고찰하였다. 그리고 Lade 모델과 수정 Lade 모델의 결과는 실험에 의하여 비교하였다. 전단변형제어속도, 상대밀도 그리고 구속압력변화에 의한 결과를 요약하면 다음과 같다. 1) 낙동강유역의 모래에 대해 Coulomb의 식을 이용할 수 있는 응력의 한계는 변형제어속도가 0.08%/min일 때 120~200 kpa이고 0.5%/min일 때 120~150 kpa의 범위로 고찰되었다. 이들 한계범위들은 석회질 모래나 양입도의 석영질 모래에 비해 적게 나타났다. 2) 변형제어속도와 상대밀도 모두가 Lade 모델과 수정 Lade 모델에 필요한 매개변수에 많은 영향을 미친다. 따라서 현장에서는 하중조건과 지반조건을 정확히 파악하여 적절한 매개변수를 사용하는 것이 중요하다. 3) 변형제어속도와 상대밀도의 변화에 따른 구성모델식에 의한 파괴시 주응력비는 전반적으로 변형제어속도에는 큰 영향을 받지 않으나, 상대밀도와 구속압력이 구성 모델식의 결과에 영향을 미치는 것으로 나타났다. 따라서 낙동강유역의 모래에 대한 응력-변형거동의 정확한 예측을 위해서는 다양한 조건에 대한 연구가 필요할 것으로 판단된다. 4) Lade 모델과 수정 Lade 모델에서 결정된 파괴시 주응력비와 파괴포락선의 내부마찰각을 실측치와 비교한 결과, 본 연구에서 사용된 구속응력 범위내에서는 Lade 모델이 수정 Lade 모델보다 평균적으로 실측치에 더 근접함을 보여 주었다.
이 논문은 자동차 타이밍벨트, 등속조인트 부트, 웨더 스트립에 적용되는 고무시스템의 손상이나 내구성 약화에 대한 사례 연구를 하는 것이 목적이다. 첫 번째 사례에서는 신품의 타이밍 벨트를 교환할 때 벨트의 내구성이 떨어진 벨트를 교환하여 타이밍 벨트와 스프로킷의 마찰작용에 의해 비정상적으로 타이밍 벨트 캔버스가 마멸된 것을 확인하였다. 두 번째 사례에서는 등속 조인트에 그리스의 밀봉역할을 하는 고무 부트의 내구성이 떨어져 경화되고 갈라져 이 틈으로 그리스가 누설된 것을 확인하였다. 세 번째 사례에서는 웨더 스트립이 화학적 변화에 따른 균열로 재료 변형이 생겨 웨더 스트립 고무가 찢어졌다. 이러한 현상은 문을 닫을 때 웨더 스트립 고무를 겹쳐지게 해 운행중 외부공기가 유입되어 미세한 소음이 발생되는 것을 확인했다.따라서, 자동차에 적용되는 고무재질의 부품들의 내구성 약화나 손상으로 인한 자동차의 고장사례가 발생하지 않도록 관리하여야 한다.
This study was carried out to investigate the free vibrational properties of traditional and replaceable species for sounding board, using piezoelectrical accelerometer and signal analyzer. In the study, the frequency equations of free-free beam carrying a concentrated mass in the transverse vibration and of free-mass beam in the longitudinal vibration were used. The results obtained were as follows. 1. Average values of dynamic modulus of rigidity of Korean commercial species measured were as follows. Paulownia tomatosa (Thunb.) Steudel: $5.590\times10^9\;dyne/cm^2$ Tilia amurensis Rupr.: $5.414\times10^9\;dyne/cm^2$ Macckia amurensis Rupr.: $10.044\times10^9\;dyne/cm^2$ Fraxinus mandshurica Rupr.: $8.876\times10^9\;dyne/cm^2$ Ulmus davidiana var.japonica Nakai: $8.677\times10^9\;dyne/cm^2$ Pinus rigida Miller: $6.33\times10^9\;dyne/cm^2$ Fraxinus rhynchophylla Hance: $4.666\times10^9\;dyne/cm^2$ 2. The ratio of dynamic transverse Young's modulus to dynamic modulus of rigidity, $E_T/G_{LT}$, was 24.922 for Fraxinus rhynchophylla Hance, which was the highest, 7.317 for Paulownia tomentosa (Thunb.) Steudel, which was the lowest among Korean commercial species measured. 3. The value of longitudinal dynamic Young's modulus was about 3.7% and 19.8%, respectively, higher than those of transverse dynamic and static Young's modulus. The value of transverse dynamic Young's modulus was about 15.5% higher than that of static Young's modulus. 4. Predicted value of MOR in terms of correlation coefficient by transverse dynamic Young's modulus was slightly higher than that of static Young's modulus, but no significance was found out. 5. Transverse dynamic Youne's modulus was $(2.002\pm0.288)\times10^{11}\;dyne/cm^2$ for Fraxinus mandshurlca Rupr., which was the highest, $(0.601\pm0.100)\times10^{11}\;dyne/cm^2$ for Paulownia tomentosa (Thunb.) Steudel, which was the lowest among Korean commercial species measured. The sound velocity of sitka spruce was 5,685 m/sec, which was the highest. 6. Internal friction of Paulownia tomentosa (Thunb.) Steudel was shown the lowest value among Korean commercial species, $(8.795\pm1.795)\times10^{-3}$, but was higher than that of sitka spruce, $(7.331\pm0.991)\times10^{-3}$. Internal friction was shown negative correlation with density and dynamic Young's modulus, respectively. 7. K value was affected largely by internal friction and was the highest, $2.225\times10^8$ for Paulownia tomentosa (Thunb.) Steudel and was the lowest, $0.550\times10^8$ for Fraxinus rhynchophylla Hance. K value of Paulownia tomentosa (Thunb.) Steudel was higher than that of sitka spruce and K values of melapi and cottonwood, which have been considered to be replaceable species with sitka spruce in the piano industry, were lower than those of Paulownia tomentosa (Thunb.) Steudel and mill amurensis Rupr.
본 연구는 장기간에 걸쳐 산 안드레아 단층계 내에서 56개 지점의 단층이동률에 대한 지질학적인 측정자료를 기준으로 모델을 설정하였다. 모델은 산안드레아 단층을 중심으로 한 수렴대에서 낮은 마찰(${\mu}$=0.3)을 갖는 단층군에 대해 최적의 결과를 보여주고 있다. 저강도를 갖는 단층에 대해 국지적인 이상값이나 대표값을 결정하는 것은 분명히 중요한 의미를 갖는다. 더욱이 이러한 연구는 지구조적인 체계에서의 단층의 강도를 결정하는 데 도움이 될 것으로 보인다. 예상치 못한 원인에 의한 공극압력이나 마찰법칙의 적절성에 대한 의문을 고려하지 않을 수 없을 것이다. 이러한 문제를 해결하기 위해서, 다른 가설하에서 단층의 유체학적인 모의 실험이 가능한 유한요소법을 적용하기 위해 세 가지의 단층분석 모델을 시도하였다. 계산된 모델은 추정된 유체역학적 특성과 판구조경계 조건을 만족하며, 현재의 지진파 표면속도, 변형률과 강도의 예측값을 나타내고 있다. 모델 연구의 결과는 평균 단층이동률, 강도의 방향과 측지학적인 자료의 예측값 범위 내에서 실제 측정치에 접근하고 있음을 보여준다. 본 연구는 저강도를 갖는 산 안드레아 단층계에서의 상호관련성을 해석하기 위한 열탄성 특성의 적용 결과를 잘 제시하고 있다.
백토안료의 제조 공정 중 분쇄 및 수비단계에서 아교수를 적용하고 이에 따른 영향을 분석하였다. 분쇄 공정에서 아교수를 적용한 경우, 일반 증류수를 사용했을 때보다 미분의 생성량이 감소하고 분급도가 향상되는 것으로 나타났다. 일반적으로 분쇄 성능 및 분쇄 한계에는 마찰력이 많은 영향을 미친다. 따라서 분쇄 조건에 따른 마찰력을 측정한 결과, 아교수를 적용한 경우 상대적으로 마찰력이 감소하는 것으로 확인되었다. 결국 분쇄 공정에서 아교수를 사용하는 것은 마찰력을 감소시켜 결과적으로 분급도를 향상시키기 위한 것으로 판단된다. 안료 제조 공정 중 수비단계에서 아교수를 적용한 결과, 아교수 적용 시 동일한 조건에서 보다 큰 입도의 입자를 수비해 내는 것이 가능한 것으로 나타났다. 이와 같은 결과는 수비액으로 아교수를 사용한 경우, 아교의 농도가 증가함에 따라 수비액의 점도가 증가하여 입자의 침강속도가 감소하기 때문인 것으로 확인되었다. 결국 수비 공정에서 아교수를 사용한 것은 수비액의 점도를 증가시켜 수비를 통해 선별할 수 있는 입도의 범위를 확대하고, 보다 세밀한 입도 구간으로 입자를 선별하기 위한 것으로 판단된다.
본 논문에서는 Coupled Eulerian-Lagrangian(CEL) 기법을 이용하여 인공섬 형식의 방호공을 구성하는 수중사면에 선박이 충돌하는 경우 발생하는 선박의 선수와 지반의 거동에 대한 매개변수 해석을 수행하였다. 고려된 매개변수는 선수의 경우 선수각, 스템각, 충돌위치 그리고 충돌속도이며, 지반의 조건으로 사면의 기울기, 지반과 선박의 마찰계수 그리고 지반의 강도이다. 선수의 거동으로부터 소산된 충돌력과 운동에너지를 각 매개변수에 대해 산정하고, 이를 지반의 변형과 연계하여 에너지 소산기구의 거동을 파악하였다. 충돌력을 변위의 지수함수로 가정하고 매개변수의 영향을 검토하였다. 그 결과 지수함수의 계수는 사면의 경사와 선박과의 마찰계수에만 영향을 받는 결과를 얻었다. 이 관계로부터 소산되는 충돌에너지를 타당하게 산정할 수 있었다. 충돌 시 선수에 의해 밀려난 원지반의 부피와 소산된 충돌에너지는 비례하는 관계로 나타낼 수 있다는 것을 보였고, 이 관계는 선박의 형상보다는 선박과 사면의 마찰계수와 지반의 강도에 영향을 받는 것으로 나타났다.
본 논문에서는 요소수를 적용하는 SCR 인젝터의 내부유동에 대한 전산 유동해석을 수행하였다. 유동해석에 적용된 인젝터는 경사진 노즐과 스월디스크를 갖는 스월타입의 단홀 인젝터이다. 인젝터 니들의 최대 리프트 및 열림 속도를 인젝터의 설계 변수로 선정하였다. 비정상 상태로 작동하는 노즐 내부의 유동 특성을 해석하기 위하여, 움직이는 물체에 적용이 가능한 Moving Grid 기법을 적용하여 정밀한 인젝터 니들의 움직임을 모사하였다. 유동해석 결과, 인젝터 니들의 속도가 증가할수록 출구를 통한 요소수 유량은 감소하는 것으로 나타났다. 이는 인젝터 니들의 속도가 빨라질수록, 인젝터 니들 하부의 빈 공간을 채우려는 유량이 증가하고, 이러한 요소수 유량의 증가가 노즐 출구로 방출되는 유량의 감소를 유발하게 된다. 요소수 유동이 인젝터 노즐에서 출구 쪽으로 진행할수록, 스월 유동은 감소하였다. 이는 유동과 노즐 벽면과의 마찰에 기인한 것으로 사료된다. 또한, 최대 리프트 유지기간에서, 니들 리프트가 높을수록 스월 계수와 평균 스월 계수가 증가하는 경향을 보였다. 본 연구의 결과는 관련된 Urea-SCR 인젝터의 기본 설계 자료로 활용될 수 있을 것이다.
A three-dimensional Lagrangian explicit time-integration finite element code for analyzing the dynamic impact phenomena was developed. It uses four node tetrahedral elements. In order to consider the effects of strain rate hardening, strain hardening and thermal softening, which are frequently observed in high-velocity deformation phenomena, Johnson-Cook model is used as constitutive model. For more accurate and robust contact force computation, the defense node contact algorithm was adopted and implemented. In order to evaluate the performance of the newly developed three-dimensional hydrocode NET3D, numerical simulations of the oblique impact of mild steel plate by mild steel sphere were carried out. Ballistic limit about various oblique angle between 0 degree and 80 degree was estimated through a series of simulations with different initial velocities of sphere. Element eroding by equivalent plastic strain was applied to mild steel spheres and targets. Ballistic limits and fracture characteristics obtained from simulation were compared with experimental results conducted by Finnegan et al. From numerical studies, the following conclusions were reached. (1) Simulations could successfully reproduce the key features observed in experiment such as tensile failure termed "disking"at normal impacts and outwards bending of partially formed plus segments termed "hinge-mode"at oblique impacts. (2) Simulation results fur 60 degrees oblique impact at 0.70 km/s and 0.91 km/s were compared with experimental results and Eulerian hydrocode CTH simulation results. The Lagrangian code NET3D is superior to Eulerian code CTH in the computational accuracy. Agreement with the experimentally obtained final deformed cross-sections of the projectile is excellent. (3) Agreement with the experimental ballistic limit data, particularly at the high-obliquity impacts, is reasonably good. (4) The simulation result is not very sensitive to eroding condition but slightly influenced by friction coefficient.
Journal of Advanced Marine Engineering and Technology
/
제37권1호
/
pp.40-46
/
2013
열전달 향상을 위하여 이차유동을 발생시켜 열전달을 증가시키는 방법에는 여러 가지가 있다. 본 연구에서는 수평채널에 다양한 형태의 립을 설치하여 유속을 변화시켰을 때의 열전달 및 압력강하 특성을 수치해석을 통하여 고찰하였다. 립은 수평채널의 아랫면에 설치하였고, 립의 높이는 5mm이다. 립이 $60^{\circ}$ 기울어지고 그루브도 설치된 경우 열전달 특성이 가장 우수하게 나타났는데, 이는 주유동이 립을 따라 흘러가면서도 유속이 어느 정도 유지되기 때문이다. 끊어진 립에서 주유동이 립의 저항을 적게 받으면서 압력강하가 가장 작게 나타났다. 모든 립의 형태에서 유속이 증가함에 따라 열전달이 향상되는 경향을 보였지만 성능계수는 감소하였다.
Gaussian dispersion model is the most widely used tool for the ground level air pollution simulation. Though in spite of the convenience there are important problems on the Pasquill- Gifford' stability classification scheme which was used to define the turbulent state of the atmosphere or to describe the dispersion capabilities of the atmosphere which was each covers a broad range of stability conditions, and that they were very site specific, and the vertical dispersion calculation formula on the case of the unstable atmospheric condition. This paper was carried out to revise the Gaussian dispension model for the purposed of increase the modeling performance and propose the revised model, which was composed of the turbulent characteristics in the unstable atmospheric conditions. The proposed models in this study were composed of the profile method, Monin-Obukhove length, the probability density function model and the lateral dispersion function which was composed of the turbulent parameters, $u_*$(friction velocity), $w_*$(convective velocity scale), $T_L$(lagrangian time scale) for the model specific. There were very good performance results compare with the tracer experiment result on the case of the short distance (<1415m) from the source, but increase the simulation error(%) to stand off the source in the all models. In conclusion, the revised Gaussian dispersion model using the turbulent characteristics may be a good contribution for the development of the air pollution simulation model.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.