• Tribology and Lubricants
• /
• v.22 no.5
• /
• pp.282-289
• /
• 2006

This paper is to investigate the wear behaviors of two type ceramics, $Al_{2}O_{3}\;and\;TiO_{2}$, by coated plasma thermal spray method under the lubricative environment. The lubricative environments are grease fluids, a general hydraulic fluids, and bearing fluids. The wear testing machine used a pin on disk type. Wear characteristics, which were friction force, friction coefficient and the specific wear rate, according to the lubricative environments were obtained at the four kinds of load and sliding velocity is 0.2 m/sec. After the wear experiments, the wear surfaces of the each test specimen were observed by a scanning electronic microscope.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.11
• /
• pp.127-133
• /
• 2003

Pin-on-disk and hardness tests using mechanical components of M-20J aircraft braking system were performed to identify the friction and wear characteristics. The intention of this work was also to analyze a 5-year term maintenance record of an M-20J aircraft. used for flight training at Hankook Aviation University, and to determine the reliability of the brake system of an M-20J aircraft. The mean wear coefficients of the lining sliding against the brake disk were compared between the test and reliability estimation to obtain a predictive wear model.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.791-794
• /
• 2003

DLC thin films were prepared by microwave plasma-enhanced chemical vapor deposition method on silicon substrates using methane ($CH_4$) and hydrogen ($H_2$) gas mixture. The negative DC bias ($-450V{\sim}-550V$) was applied to enhance the adhesion between the film and the substrate. The films were characterized by Raman spectrometer. The surface morphology was observed by an atomic force microscope (AFM). And also, the friction coefficients were investigated by AFM in friction force microscope (FFM) mode, which were compared with the pin-on-disc (POD) measurement.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.842-845
• /
• 2003

DLC thin films were prepared by microwave plasma-enhanced chemical vapor deposition method on silicon substrates using methane ($CH_4$) and hydrogen ($H_2$) gas mixture. The negative DC bias ($-450V{\sim}-550V$) was applied to enhance the adhesion between the film and the substrate. The films were characterized by Raman spectrometer. The surface morphology was observed by an atomic force microscope (AFM). And also, the friction coefficients were investigated by AFM in friction force microscope (FFM) mode, which were compared with the pin-on-disc (POD) measurement.

• Tribology and Lubricants
• /
• v.24 no.2
• /
• pp.72-76
• /
• 2008

There are 5 kinds of architectural fabrics in our country recently. The test piece were made by attaching on the steel disk which has been tested of various range of the test conditions in pin-on-disk wear testing machine. The results show that the friction coefficient and wear rate of the architectural fabrics are heavily dependent on the load and materials. PVDF type was better than others in wear rate and friction coefficient.

• Tribology and Lubricants
• /
• v.15 no.2
• /
• pp.156-163
• /
• 1999

The mechanical characteristics of the high speed steel by Powder metallurgy Process (PM-HSS) has been reported to improve with several alloying constituents, such as high carbon, vanadium and cobalt. In this paper, sliding wear test has been conducted using a pin-on-disc machine for three PM-HSS which contains 0%, 5% and 12% cobalt respectively, in order to evaluate the effect of cobalt on wear properties of PM-HSS. The results of this study showed that the wear resistance of PM-HSS has been increased by the addition of cobalt on the range of experimental friction velocities. When compared with the effect of addition of cobalt, the wear resistance of PM-HSS with 5% cobalt has been found to be superior to that of PM-HSS with 12% cobalt.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.46 no.4
• /
• pp.495-502
• /
• 2010

The effect of load and sliding speed on abrasive wear characteristics of glass fiber/polyurethane (GF/PUR) composites were investigated at ambient temperature by pin-on-disc friction test. The friction coefficient, cumulative wear volume and surface roughness of these materials against SiC abrasive paper were determined experimentally. Experimental results showed that the surface roughness of the GF/PUR composites was increased as applied load was higher in wear test. The cumulative wear volume tended to increase nonlinearly with increase of sliding distance and depended on applied load and sliding speed for these composites. It could be verified by scanning electric microscopy (SEM) photograph of surface tested that major failure mechanisms were lapping layers, ploughing, delamination, deformation of resin and cracking.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.5
• /
• pp.41-47
• /
• 1994

An optimal brake pad must have stable friction, low wear and least amount of squeal. In this study, the friction, wear and squeal behavior of some non-asbestos Kevlar materials have been evaluated experimentally. Four specimens with different formulations and a pin-on-disk machine were used for this study. To determine the role of each component in friction and squeal of a brake pad, statistical correlations have been obtained and discussed. The components tested were : Kevlar, Steel Powder, Barium Sulfate and fillers combined by Resin.

• Proceedings of the KWS Conference
• /
• 2001.05a
• /
• pp.114-116
• /
• 2001

This study deals with friction stir welding of aluminum alloy(A5083). Welding conditions were applied that revolution 2000rpm, friction pressure 25MPa, angle between stir rod section and plate 4$^{\circ}$, projection pin diameter 4mm, traverse speed 0.5mm/sec, 1.0mm/sec, 1.5mm/sec. The experimental results as follows; 1. Welding beads were superior in traverse speed 1.0mm/sec and it were formed plenty of flash in traverse speed 0.5 mm/sec. Welding beads were rough in traverse speed 1.5mm/sec. 2. The maximum tensile strength was 211MPa in traverse speed 1.0mm/sec, in this case the strength was 85% of A5083 base metal tensile strength.

• Tribology and Lubricants
• /
• v.24 no.5
• /
• pp.234-240
• /
• 2008

It is well known that surface texturing improves the tribological properties of mechanical components for enhancing hydro-dynamic effect or serving as a micro reservoir. There are not, however, enough researches to reveal the effects of surface texturing on the tribological properties under grease lubrication which is used in lubricating many mechanical elements. In the present study, therefore, the effects of surface texturing on the tribological properties are investigated under grease lubrication based on an experimental approach. The results show that surface texturing decreases friction coefficient. It is found that the friction coefficient can be decreased by controlling the diameter and density of micro-dimple. The diameter of dimple is more effective under high load and low speed than otherwise. And, the density of dimple is effective under low load and high speed.