• 설비공학논문집
• /
• 제19권1호
• /
• pp.1-9
• /
• 2007

Water condensate accumulated on the surface of a fin-and-tube heat exchanger significantly affects its thermal and hydraulic performance. The purpose of this study is to investigate the effect of condensate retention on the air-side heat transfer performance and flow friction. Total 12 samples of slit and plate fin-and-tube heat exchangers with varying fin spacing and number of tube rows are tested under dry and wet conditions. The thermal fluid measurements are made using a psychometric calorimeter. Frontal air velocity varies in the range from 0.7 m/s to 1.5 m/s. Using the experimental data, presented are the heat transfer coefficients in terms of Colburn j-factor and friction factor.

• 한국정밀공학회지
• /
• 제18권11호
• /
• pp.67-73
• /
• 2001

This paper aims at developing a torque model for the high-speed tapping with small-diameter taps. As recent industries such as automobile and information technology grows, taps smaller than 5mm in diameter are needed much more. In that occasion, the friction force between a tap surface and a workpiece plays much more important role in the tapping torque than in he larger tapping. Tapping mechanism was analysed based on the tap geometry. It has two steps : one is a forward cutting composed of the chamfered threading and full threading and the other is the backward cutting. The torque by the cutting force in the chamfered threading is calculated using the cutting area and the specific cutting force while the torque by the friction force, which is rather dominant than the cutting force both in the full threading and in the backward cutting, is calculated using the normal force on the threads and the friction coefficient. The experiment has shown that the results by the proposed torque model fit quite well with the acutal measurements within the error of 10%.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1994년도 가을 학술발표회 논문집
• /
• pp.119-122
• /
• 1994

An analytical procedure is described to estimate the mobilized tensile forces along the effective lengths of nails. Based on the horizontal focing displacements of a nailed-soil wall experiencing outward tilt about the toe with granular soil deposit, the variation of nail-soil friction coefficient is modeled. Also, the method of overall stability analysis of a nailed-soil wall is presented using the Morgenstem-Price limit-equilibrium slice method. The results predicted by the developed procedure are compared with test measurements. The comparisons show in general good agreement.

• 한국가시화정보학회지
• /
• 제9권1호
• /
• pp.20-28
• /
• 2011

An experimental assessment has been made of the drag reducing efficiency of the outer-layer vertical blades, which were first devised by Hutchins. The drag reduction efficiency of the blades was reported to reach as much as 30%. However, the drag reduction efficiency was quantified only in terms of the reduction in the local skin-friction coefficient. In the present study, a series of drag force measurements in towing tank has been performed toward the assessments of the total drag reduction efficiency of the outer-layer vertical blades. A maximum 9.6% of reduction of total drag was achieved. The scale of blade geometry is found to be weakly correlated with outer variable of boundary layer. In addition, detailed flow field measurements have been performed using 2-D time resolved PIV with a view to enabling the identification of drag reduction mechanism.

• Tribology and Lubricants
• /
• 제35권2호
• /
• pp.106-113
• /
• 2019

We investigated the application of tetrahedral amorphous carbon (ta-C) coatings to fabricate a glass lens manufactured using a glass molding process (GMP). In this work, ta-C coatings with different thickness (50, 100, 150 and 200 nm) were deposited on a tungsten carbide (WC-Co) mold using the X-bend filter of a filtered cathode vacuum arc. The effects of thickness on mechanical and tribological properties of the coating were studied. These ta-C coatings were characterized by atomic force microscopy, scanning electron microscopy, nano-indentation measurements, Raman spectrometry, Rockwell-C tests, scratch tests and ball on disc tribometer tests. The nano-indentation measurements showed that hardness increased with an increase in coating thickness. In addition, the G-peak position in the Raman spectra analysis was right shifted from 1520 to $1586cm^{-1}$, indicating that the $sp^3$ content increased with increasing thickness of ta-C coatings. The scratch test showed that, compared to other coatings, the 100-nm-thick ta-C coating displayed excellent adhesion strength without delamination. The friction test was carried out in a nitrogen environment using a ball-on-disk tribometer. The 100-nm-thick ta-C coating showed a low friction coefficient of 0.078. When this coating was applied to a GMP, the life time, i.e., shot counts, dramatically increased up to 2,500 counts, in comparison with Ir-Re coating.

• 대한교통학회지
• /
• 제28권3호
• /
• pp.119-130
• /
• 2010

교통사고의 재구성 해석은 도로와 사고흔적, 자동차 손상 등 다양한 자료들을 분석함으로서 이루어진다. 대부분의 자료들은 사고 해석에서 변수로 작용하며, 측정으로부터 구해지는 자료들은 조사자와 도구, 주어진 환경 등에 의해 측정 오차가 발생된다. 따라서 사고해석에서는 측정 오차에서 비롯되는 불확실성이 항상 존재한다. 본 연구는 불확실성이 존재할 가능성이 매우 높은 도로 기하구조와 타이어 흔적 등 길이와 마찰계수 등에 대해 반복 측정 실험을 함으로서 교통 사고해석에서의 불확실성을 정량화하였다. 또한 자동차 충돌 변형량의 사진 계측에 대한 불확실성에 대해서도 해석 결과를 제시하였다. 이러한 통계학적 분포들은 사고 재구성 불확실성을 추정하기 위해 입력 계수의 적절한 범위를 결정하는 것을 도울 수 있다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2273-2278
• /
• 2007

Brazed Plate Heat Exchanger (BPHE) is a type of compact plate heat exchanger with parallel corrugated plates which are brazed together in series. Each plate hascorrugation called herringbone pattern. Inside a BPHE, hot fluid and cold fluid alternate its flow direction to establish counter current flow configuration. Two-phase flow heat transfer and pressure drop of R-22 in BPHE were experimentally measured in this study. In the present experiments, single-phase region and two-phase region coexist in a BPHE. Therefore, the inside of a BPHE have to be divided into single phase region and two phase region and analyzed accordingly. The results from the single phase flow analysis are then extended to the two phase flow analysis to correlate the condensation and evaporation heat transfer and pressure drop for the refrigerant R-22 in the BPHEs. Previous models for two- phase friction factor have been compared with the present experimental results.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.225-226
• /
• 2002

In this work, the friction and wear behavior under' various lubrication regimes were investigated. The objective of this work is to develop an Accelerated Life Test (ALT) method for the durability evaluation of a machine element which is operated under lubrication. Electric contact resistance and frictional forces were measured with respect to a wide range of the loads and speeds under various lubrication regimes using a pin-on-disk type tribotester. From the experimental results, it could be found that an effective and reliable ALT method could be achieved by controlling the lubrication regime through the measurements of friction coefficient and contact resistance with respect to load and sliding speed.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.627-632
• /
• 2006

An experimental study is conducted to investigate the effect of the tube row and fin spacing on the air-side heat transfer and friction characteristics of fin-tube heat exchangers with slit fin pattern. A total of twelve samples of fin-tube heat exchangers with the nominal tube diameter of 7 mm, transverse tube pitch of 19 mm and longitudinal tube pitch of 12.5 mm are tested. The thermal fluid measurements are made using a psychometric calorimeter. The raw data are reduced to the desired heat transfer coefficient in terms of j-factor and friction factor of f for various frontal air velocities, fin pitches and number of tube rows.

• Tribology and Lubricants
• /
• 제25권1호
• /
• pp.20-24
• /
• 2009

TiC-derived carbon coatings have been synthesized at $600^{\circ}C$ temperature treatment with $H_2/Cl_2$ mixture gases. From Raman spectroscopy measurements, the modified layer was covered with carbon and the thick-ness of the layer was increased with increasing reaction time. And $I_D/I_G$ ratio was decreased with increasing reaction time. The superior tribological property was obtained from TiC reacted with $Cl_2$ gas for 2 hrs. And the tribological property measurements indicate that TiC-derived carbon layer has $0.9{\times}10_{-6}mm^3/Nm$ in wear coefficient and 0.13 in friction coefficient.