• Proceedings of the KWS Conference
• /
• 2006.10a
• /
• pp.109-111
• /
• 2006

In this study, microstructure and mechanical properties for the friction stir welded 2519Al-T87 alloy of the thickness of 38.8mm were studied using DSC, OM, SEM and micro hardness tester. DSC analysis show that GP Zone, ${\theta}'$ and $\theta$ phases in upper part and ${\theta}'$ and $\theta$ phase in lower part of the FSW zone. Recrystallized large grains are observed in HAZ, and elongated small and large grain in the TMAZ. In SZ, very small grains forms by high plastic deformation and heat from friction by tool and specimen.

• Proceedings of the KWS Conference
• /
• 2001.10a
• /
• pp.211-213
• /
• 2001

• Journal of Welding and Joining
• /
• v.31 no.1
• /
• pp.33-37
• /
• 2013

Robotized MIG welding of large aluminium components for high speed trains is state-of-the-art. The implementation of online laser cameras enables seam tracking and adoptive modification of welding parameters. A constant fill is achieved regardless of the gap tolerances. Friction Stir Welding has been introduced to the market as a reliable and fast joining technology. The advantages of high welding speeds and the elimination of arc light, fumes and liquefaction in the welding spot lead to economical realisation of heavy-duty gantry systems. FSW robots offer a high flexibility with regard to welding of curved parts, and can be equipped with laser cameras for exact joint tracking.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.328-331
• /
• 2007

It was carried out to evaluate microstructure and mechanical properties of friction stir welded(FSW) on magnesium alloys. Two types magnesium alloy was used in this work, AZ31 wrought and AZ91 cast magnesium alloy. Microstructure near the weld zone showed general weld structures such as stir zone(SZ), thermo-mechanically affected zone(TMAZ) and heat affected zone(HAZ). In the AZ91 alloy, the SZ had a fine grain size and $\beta$ phase particles which were well distributed in matrix. It was characterized to redistribute by partial or full re-solution of the $\beta$ phase which is coarse in base metal during FSW processing. The hardness of the SZ slightly increase than the base metal in AZ31 Mg alloy.

• International Journal of Advanced Culture Technology
• /
• v.3 no.1
• /
• pp.179-187
• /
• 2015

This study presents the experimental results of the Friction Stir Welding (FSW) of AA6063 aluminum alloy and AISI304 stainless steel butt joint by varying the welding parameters such as the rotating speed and the welding speed. The main results are as follows. The variation of the welding parameters produced various characteristic interfaces and had distinct influences on the joint properties. Increasing the rotating speed and the welding speed decreased the joint tensile strength because it produced the defect on the joint interface. The optimum welding parameter that could produce the sound joint was a rotating speed of 750 rpm and the welding speed of 102 mm/min with the tensile strength of 71 MPa.

• Journal of Welding and Joining
• /
• v.29 no.5
• /
• pp.82-89
• /
• 2011

The effect of welding condition on tensile properties of KS5J32 Al Alloy was investigated under various welding conditions. The 1.6 mm thick KS5J32 alloy sheets were joined by friction stir welding (FSW) technique with butt joint. The tool rotation speeds were 1000, 1250 and 1500 rpm, and the welding speeds were varied within the range from 100 to 600 mm/min. Voids mainly occurred at the advancing side of the tool probe, when the tool rotation speed was low, due to insufficient materials flow. When the weld pitch exceeded 0.4 mm/rev, voids were observed under all welding conditions and the area of voids increased with increasing weld pitch. For void-free specimens, fracture always occurred at base materials. However voids affected the location of fractures, base metal or welded zone, when the voids existed within the welds.

• Proceedings of the KWS Conference
• /
• 2004.05a
• /
• pp.156-158
• /
• 2004

The microstructural evolution in a 304 stainless steel weld during FSW was examined. The SZ and TMAZ showed typical dynamically recrystallized and recovered microstructures, respectively, The microstructural observation revealed that sigma phase was formed at the advancing side of the stir zone. A possibility was suggested that the rapid formation of the sigma phase is related to the transformation of austenite to delta-ferrite in the stir zone, from introduction of high strain and dynamic recrystallization during FSW.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.729-730
• /
• 2012

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.1077-1078
• /
• 2013

• Journal of the Korean Society of Industry Convergence
• /
• v.27 no.1
• /
• pp.9-15
• /
• 2024

In this study, the mechanical properties of friction stir welded A6061-T6 were evaluated. This material is used as a battery pack case material for electric vehicles. The Vickers hardness, tensile strength, and yield stress of the friction stir welding (FSW) specimen were all smaller than those of the base metal specimen. As the heat input increased, the nugget zone widened, and there were differences in hardness according to the base metal zone, heat affected zone, thermal-mechanical affected zone, and nugget zone. Mechanical properties were not proportional to heat input, and the thermal-mechanical affected zone on the advancing side was the smallest in all conditions. This is because the material flow speed increased on the advancing side, where the welding direction and the tool rotation direction were the same, forming a distinct boundary with mechanical deformation.