• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.72-76
• /
• 2003

In this paper, active frequency doubler with broadband characteristics and unconditional stability from 6GHz to 12GHz was designed and fabricated using PHEMT. The designed frequency multiplier has a bias point near pinch-off and a proposed RC circuit between bias line and input matching network for the improvement of stability. With 0dBm input power, second harmonic of 1.7dBm at 12GHz, - 27.5dBc suppression of 6GHz fundamental, -18dBc suppression of 18GHz 3rd harmonic and the output bandwidth of 1.8GHz have been measured.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.10
• /
• pp.1872-1879
• /
• 1994

The design and implementation of Ku-Band frequency synthesizer was accomplished by the use of PLL and frquency multiple method. Design procedure and operation characteristics of PLL circuit were analyzed on the basis of control theory to synthesize about 1 GHz frequency which should be stable. By connecting frequency doubler and frequency eighth multiplier to the designed PLL circuit in series, Ku-Band frequency was synthesized. The validity of design method of Ku-Band frequency synthesizer was verified through experimental results.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.4 s.346
• /
• pp.75-80
• /
• 2006

This paper has proposed a novel dual band transmitter module which can be operating either as an amplifier or as a frequency multiplier according to the input frequency. A conventional dual band transmitter consists of separate amplifiers operating at each frequency band, but the proposed dual band module operates as an amplifier for the IEEE 802.11b/g signal, and as a frequency doubler for the IEEE 802.11a signal according to input frequency and bias voltage. In this paper, we have obtained sharp stop band characteristics by using microstrip DGS(Defected Ground Structure) to suppress the fundamental frequency of the frequency doubler as well as the second harmonic of the amplifier. From measurement result, second harmonic suppression is below -59dBc in the amplifier mode, and fundamental suppression is below -35dBc in the frequency doubler mode. And the designed module has 17.8dBm output P1dB at 2.4GHz and 10.1dBm power for 5.8GHz output, and the output power in the two modes are 0.8dB and 2.8dB larger than the module with ${\lambda}g/4$ reflector, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.12A
• /
• pp.1019-1024
• /
• 2003

In the thesis, we propose a new type of the predistortion linearizer using frequency multiplier The linearizer utilizing the 2nd and 3th harmonic used the individual control of the 3rd and 5th order intermodulation distortion(IMD) component. This structure is composed of wilkinson power combiner for combine and isolation of output signal, 3rd order IMD product controller using doubler and 5th order IMD product controller using tripler. The proposed predistortion linearizer controlled by individual order is obtained for about -16 dBc and 18 dBc of 3rd order and 5th order IMD components, respectively, over the frequency band 870 MHz to 880 MHz at the output power of 34 dBm/tone.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.6
• /
• pp.959-968
• /
• 2000

In this paper, a low phase noise frequency synthesizer used to TX local oscillator in BWLL RF tranceiver is presented. The phase-locked stable 25GHz-band frequencies in BWLL TX LO are obtained by using 2 GHz baseband frequency synthesizer, sixth-harmonic frequency multiplier and frequency doubler at 12 GHz band frequency input. The 25 GHz band frequency synthesizer presented in this paper has 3-output frequencies at 24.92 GHz, 25.10 GHz, 25.26 GHz. At 24.92 GHz frequency the synthesizer has 0.44 dBm output power and shows -87.93 dBc/Hz(a 10 KHz), -109.54 dBc/Hz (a100 KHz) phase noise characteristics .

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.6
• /
• pp.195-200
• /
• 2018

A W-band frequency octupler is implemented on 100-nm GaAs pHEMT process. The fabricated octupler can be used as a local oscillator or a signal source of W-band transceivers. Three common-source doublers are connected in cascade to multiply an input signal of 10.75 GHz to 83 GHz. A common-source amplifier is followed for each doubler to improve the conversion gain and suppress the unwanted harmonics. The fabricated octupler showes high output of more than 6 dBm in the 80 - 84 GHz band and achieved excellent spurious suppression performance over 20 dBc.