• The Journal of the Acoustical Society of Korea
• /
• v.43 no.4
• /
• pp.383-390
• /
• 2024

When measuring the radiated noise of an underwater vehicle, the range information between the vehicle and the receiver is an important factor, but since Global Positioning System (GPS) is not available in underwater, an alternative method is needed. As an alternative, the range is measured by estimating the arrival time, arrival time difference, and arrival frequency difference using a separate acoustic signal. However, errors occur due to the channel environment, and these outliers become obstacles in continuously measuring range. In this paper, we propose a method to reduce errors by curve fitting with a function in the form of a V-curve as a post-processing to remove outliers that occurred in the process of measuring range information. Simulation, lake and sea trials were conducted to verify the performance of the proposed method. In the results of the lake trial, the range estimation error was reduced by about 85 % from the Root Mean Square Error (RMSE) point of view.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.4
• /
• pp.611-614
• /
• 2021

In this paper, we propose a widerange array microphone for lecturer tracked with Frequency Modulated Continuous Waveform (FMCW) radar sensor. Time Difference-of-Arrival (TDoA) is often used as audio tracking, but the tracking accuracy is poor because the frequency of the voice is low and the relative frequency change is large. FMCW radar has a simple structure and is used to detect obstacles for vehicles, and the resolution can be archived to several centimeter. It is shown that the sensor is useful for detecting a speaker in open area such as a lecture, and we propose an wide range 4-element array microphone beamforming system. Through some experiments, the proposed system is able to adequately track the location and showed a 8.6dB improvement over the selection of the best microphone.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.156-162
• /
• 2006

Pipe thinning is one of the major issues for the structural fracture of pipes of nuclear power plants. Therefore a method to inspect a large area of piping systems quickly and accurately is needed. In this paper, we proposed the method for monitoring pipe thinning. Our basic idea come from that a group velocity of impact wave is different as wall thickness. If the group velocity is measured, wall thickness can be estimated. To obtain the group velocity, time-frequency analysis is used. This is because an arrival time difference can be measured easily in time-frequency domain rather than time domain. To test the performance of this technique, experiments have been performed for a plate and U type pipe. Results show that the proposed technique is quite powerful in the monitoring pipe thinning.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.8C
• /
• pp.742-749
• /
• 2009

In this paper, we propose mitigation techniques using time-domain shortening filter (TSF) and frequency-domain shortening filter (FSF) to overcome inter-block interference (IBn and inter-carrier interference (ICn due to the time difference of arrival (TDoA) and carrier frequency offset (CFO) between downlink and uplink signals from access point (AP) and subscriber station (SS) in synchronous digital duplexing (SDD)/orthogonal frequency division multiple access (OFDMA) systems for indoor wireless communication. The proposed TSF and FSF maximize SIR for shortening in time (SIRST) and SINR for shortening in frequency (SINRSF), respectively, by using channel impulse responses and timing information among stations, obtained from mutual ranging procedure. It is verified by computer simulation that the proposed TSF and FSF reduce effectively the effects of IBI and ICI in the SDD/OFDMA systems.

• The Journal of the Acoustical Society of Korea
• /
• v.35 no.6
• /
• pp.419-426
• /
• 2016

Measurements of bottom loss as a function of grazing angle (in range of $9{\sim}14^{\circ}$) at a frequency range of 4 ~ 8 kHz were conducted on an experimental site off Geoje island in October 2015. Geoacoustic inversion of the surficial sediment thickness is performed using the arrival time difference between the surficial layer and the sub-bottom layer reflected signal. To invert the thickness of surficial sediment, we used the grain size of $8{\sim}10{\phi}$ obtained by KIGAM (Korea Institute of Geoscience and Mineral Resources). The thickness of the surficial sediment was estimated to be 4 ~ 7 m. Finally, this inversion result was compared with the geoacoustic observation conducted by the KIOST (Korea Institute of Ocean Science & Technology) using sub-bottom profiler.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.1A
• /
• pp.17-24
• /
• 2012

In this paper, we described a received signal model in terms of the starting point of FFT window and derive a post-detection SINR for the receiver with MMSE filter and the corresponding filter coefficients in order to mitigate the effects of interferences caused by time and frequency selective fading channels and time difference of arrival (TDoA) in OFDMA-based Mesh Networks. In addition, we proposed an MMSE Bidirectional Successive Detection (BSD) technique which can suppress the effects of interferences among multi-nodes without any redundant FFT operations. It was shown by simulation that the proposed interference suppression technique has not an error floor at higher average SNR than 30dB in terms of 64QAM uncoded BER contrary to the conventional techniques.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.20 no.6
• /
• pp.490-500
• /
• 2000

A new technique for the source location of acoustic emission (AE) in plates whose thichness are close to or thinner than the wavelength has been studied by introducing wavelet transform de-noising technique. The detected AE signals were pre-processed using wavelet transform to be decomposed into the low-frequency, high-amplitude flexural components and the high-frequency, low-amplitude extensional components. If the wavelet transform de-noising was employed, we could successfully filter out the extensional wave component, one of the critical errors of source location in plates by arrival time difference method. The accuracy of source location appeared to be significantly improved and independent of the setting of gain and threshold, plate thickness, sensor-to-sensor distance, and the relative position of source to sensors. Since the method utilizes the flexural component of relatively high amplitude, it could be applied to very large, thin-walled structures in practice.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.6A
• /
• pp.568-576
• /
• 2011

In this paper, a channel assignment technique to mitigate interferences due to ISI(Inter Symbol Interference) and ICI(Inter Carrier Interference) caused by TDoA(Time Difference of Arrival) among distributed MRs(Mesh Routers) in OFDMA(Orthogonal Frequency Division Multiple Access)-based WMN(Wireless Mesh Network) is proposed. The SINR(Signal to Interference and Noise Ratio) associated with the channel assignment for each MR is defined to minimize the effect of ISI and ICI due to TDoA in WMN, which is then used to propose an channel assignment technique considering fairness constraint. It is verified by computer simulation that the proposed channel assignment technique can improve the performance of BER(Bit Error Rate) in WMNs with compared to the conventional technique.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.1
• /
• pp.53-60
• /
• 2010

This paper dealt with the acoustic detection of partial discharge (PD) in insulation oil for insulation diagnostics of oil immersed transformers. Electrode systems such as needle to plane, plane to plane, and floating were fabricated to simulate some defects in transformers. A wide band acoustic emission(AE) sensor with the frequency ranges of 100 kHz~1 MHz and a narrow band AE sensor with the resonant frequency of 140 kHz were used in the experiment. Also, a decoupler and an amplifier were designed to detect and amplify the acoustic signal only. The decoupler separates acoustic signal from DC source without any distortion, and the amplifier has the gain of 40 dB in frequency ranges of 11 kHz~4 MHz. In the experiment, frequency components and propagation characteristics of acoustic signal were analyzed, and an algorithm of positioning of PD occurrence by the time difference of arrival was proposed. From the results, the frequency components of the acoustic signal exist from 50 kHz to 200 kHz and the positioning error of PD calculated by three AE sensors was within 1%.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.5
• /
• pp.1-14
• /
• 1997

We consider transmission beamforming techniques for frequency-division-duplex (FDD) wireless communication systems using adaptive arrays to improve the signal quality of the array transmission link. We develop a simple effective transmission beamforming technique based on an approximated frequency tranlsation (AFT) to derive the tranmsiion beamforming weights from the uplink channel vector. This technique exploits the invariance of the short-time averaged fast fading statistics to small frequency translations. A simple approximate relationship that relates the transmission channel vector to the reception channel vector is derived. We have developed its practical alternative in which the frequency translation of the channel vector is performed at the principal angle of arrival (AOA) of the u;link synthestic angular spectrum instead of the mean AOA. To analyze the performance of the proposed methods, we consider the power loss incurred by applying the estimated channel vector instead of the true downlink channel vector. The performance is analyzed as a function of the mean AOA, the angular spread, the number of elements, frequncy difference between the uplink and the downlink, and the angle distribution. Their performance is also compared with that of the direct weight reuse method and the AOA based methods.