• Geomechanics and Engineering
• /
• v.37 no.2
• /
• pp.179-187
• /
• 2024

In this paper, a unified time-dependent constitutive model of Darcy flow and non-Darcy flow is proposed. The influencing factors of flow velocity are discussed, which demonstrates that permeability coefficient is the most significant factor. Based on this, the dynamic evolution characteristics of water inrush during tunneling through fault fracture zone is analyzed under the constant permeability coefficient condition (CPCC). It indicates that the curves of flow velocity and hydrostatic pressure can be divided into typical three stages: approximate high-velocity zone inside the fault fracture zone, velocity-rising zone near the tunnel excavation face and attenuation-low velocity zone in the tunnel. Furthermore, given the variation of permeability coefficient of the fault fracture zone with depth and time, the dynamic evolution of water flow in the fault fracture zone under the variable permeability coefficient condition (VPCC) is also studied. The results show that the time-related factor (α) affects the dynamic evolution distribution of flow velocity with time, the depth-related factor (A) is the key factor to the dynamic evolution of hydrostatic pressure.

• Journal of Acupuncture Research
• /
• v.18 no.6
• /
• pp.53-58
• /
• 2001

Objective : The purpose of this study is to investigate the characteristics of patients with fracture admitted in oriental hospital. Methods : From october 1996 to october 2001, we retrospectively evaluated the simple radiographic proven 8441 patients with musculoskeletal pain in oriental hospital. The patients included 3899 men and 4542 women. All fractures were analyzed in terms of location, age and sex. Results : 1. The fracture rate of radiologic study was relatively high in foot, chest, upper extremity and hand. The frequent fractures were in spine (257 cases), foot (119 cases), upper extremity (83 cases). and chest (68 cases). 2. The male patients with fracture were significantly higher than female in 0-40 years group: in 0-20 years group(8.5 % vs 4.0 %, p<0.01), in 21-40 years group (4.1 % vs 2.6, p<0.05), while female patients with fracture were significantly higher than male patients in more than 60 years group( 10.1 % vs 15.4 %, p<0.01). 3. The incidence of fracture showed significant association with increased age except 0-20 years group(p<0.01). Spine and chest cage in mate, and upper extremity, pelvis, spine, ankle and chest cage in female were significantly higher on older age groups. Conclusion : The overall fracture rate of radiologic study was 6.6 % for patients with musculoskeletal problem admitted in oriental hospital. The distribution of fracture showed significant difference in terms of age, sex and site. So we believe the radiologic study is helpful to evaluate fracture in oriental hospital.

• Journal of the Korean Society of Safety
• /
• v.32 no.6
• /
• pp.9-15
• /
• 2017

Recently many researches were conducted on the interlaminar fracture that is a delamination between laminates by using ASTM standardized methods. However the experiment of the intralaminar a fracture is difficulty. In this study, four types of CFRP/GFRP composites with different layer structures were compared to evaluate an intralaminar fracture toughness under the mode I. Also the CNTs were added to the layer for the examination of the fracture toughness improvement. And the characteristics of the crack propagation behaviour was observed using a microscope. The obtained results can be useful for the evaluation of the intralaminar fracture toughness of the CNT reinforced CFRP/GFRP composites.

• Proceedings of the KSR Conference
• /
• 2004.06a
• /
• pp.865-871
• /
• 2004

The safety evaluations of railway wheel sets make use of the static fracture toughness obtained in ingot materials. The static fracture toughness of wheelset materials has been extensively studied by experiments, but the dynamic fracture toughness with respect to wheel set materials has not been studied enough yet. It is necessary to evaluate the characteristics of the fracture mechanics depending on each location for a full-scale wheel set for high-speed trains, because the load state for each location of the wheel set while running is different the contact load between the wheel and rail, cyclic stress in the wheel plate, etc. This paper deals with the fracture toughness depend on load rates. The fracture toughness depending on load rate data shows that once the downward curve from quasi-static values was reached, subsequent values showed a slow increase with respect to the impact velocity. This means that dynamic fracture toughness should be considered in the design code of the wheelset material.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.790-791
• /
• 2006

The fracture behavior and mechanical characteristics of sintered rare-earth magnets were investigated. It shows that the fracture behavior and bending strength of the magnets obviously exhibit anisotropy. Sm-Co magnets tend to cleavage fracture in the close-packed (0001) plane or in the ($10\bar{1}1$) plane. The fracture mechanism of $Nd_2Fe_{14}B$ magnet mainly appears to be intergranular fracture. The anisotropy of fracture behavior and mechanical strength of sintered rare-earth magnets is caused mainly by the strong crystal-structure anisotropy and the grain alignment texture. The effects of Nd content, and Pr, Dy substitution on the impact stability of $Nd_2Fe_{14}B$ magnets were also reported.

• Journal of the Korean GEO-environmental Society
• /
• v.2 no.1
• /
• pp.37-56
• /
• 2001

As a preliminary study to establish fracture network model in crystalline rocks, detail investigation on fracture characteristics were performed. Five fracture sets were determined on the basis of regional survey of geological structures and fractures on outcrops. Among the fracture sets, S1 set has the highest density and longest trace length of fractures which was identified on surface in the study area. S4 and S5 sets are composed of foliations and foliation parallel shear joints of gneisses, which are very important sets at the aspect of weighting of fracture length. For characterization of subsurface fractures, detail core logging was performed to identify fractures and fracture zones from five boreholes. Acoustic televiewer logging and borehole geophysical loggings produced images, orientations and geophysical properties of fractures which intersect with boreholes. According to the result of the investigations, subsurface fractures can be grouped as three preferred orientations(B1, B2 and B3), which correspond to S1, S2 and S4/S5 of surface fracture sets, respectively. Actually, B1 set is expected to be intensely developed at subsurface. However, it has low frequency of intersection with boreholes due to its parallel or sub-parallel direction to boreholes. According to the inference of conductive fractures, B1 and B3 sets have possibilities of water flow and their intersection lines are also thought to consist of important conduits of groundwater flow. In particular, faults which are parallel to foliations control major groundwater flow in the study area.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.790-799
• /
• 2010

The Upper Devonian Grossmont Formation in Alberta, Canada reserves an estimated 50 billion cubic meters of bitumen and possess about 1/6 of the total bitumen resources in northern Alberta. However, unlike the overlying Athabasca oil sands, non conventional bitumen resources has not been developed as yet. The carbonate rocks of Grosmont Formation have been subject to various stages of diagenesis, including dolomatization and karstification with a strong effect on the distribution of porosity and permeability, which resulted in highly heterogeneous reservoirs. An extensive fracture logging and mapping was performed on total of six boreholes located in the study area to explore the characteristics of fracture geometry system and the subsurface structures of carbonates reservoir that holds bitumen. Fractal dimension was used as a measure of the statistical homogeneity of the fractured rock masses. The applicability of random Cantor dust, Dc, as a fractal parameter was examined systematically. The statistical homogeneity of fractured carbonates rock masses was investigated in the study area. The structural domains of the rock masses were delineated depthwise according to estimated Dc. The major fracture orientation was dominated by horizontal beddings having dip of $0-20^{\circ}$. Also, fractures having high dip angles existed with relatively low frequency. Three dimensional fracture network modeling for each structural domain has been performed based on fracture orientation and intensity, and some representative conceptual models for carbonates reservoir in the study area has been proposed. The developed subsurface conceptual models will be used to capture the geomechanical characteristics of the carbonates reservoir.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.583-588
• /
• 2002

The purpose of the study is to evaluate fracture toughness on the Laser and the electron beam welded joints of high tensile steels (HT500, HT550, HT650) by using 3-point bend CTOD and Charpy impact test. WM (weld metal) CTOD tests have been carried out using two kinds of CTOD specimen, the Laser beam welding (108mm length, and 24mm width, and 12mm thickness) and the electron beam welding (l71mm length, and 38mm width, and 19mm thickness). WM Charpy impact specimen is a standard V-notch type, and the temperature of the experiment is changed from -45 to 20 degree of centigrade. FE-analysis is also performed in order to investigate the effect of stress-strain fields on fracture characteristics. Results of the standard V-notch Charpy test are influenced by strength mis-match effect and the absorbed energy vE depends on crack path, and The transition temperature of Laser beam welded joints is more higher than that of electron beam welded joints. Results of the 3-point bend test give low critical CTOD and the crack path is in the weld metal of al specimens. These results indicate fracture toughness characteristics of the welded joints and transition temperature of HT500 are similar both a Laser beam welded joint and an electron beam welded joint. But the fracture toughness and the transition temperature of the electron beam welded joints of HT550 and HT650 are higher than those o the Laser beam welded joints.

• Composites Research
• /
• v.34 no.5
• /
• pp.323-329
• /
• 2021

In this paper, the characteristics of fracture in mode I loading were analyzed for adhesively bonded joints with non-uniform adhesion. The Double Cantilever Beam test was performed and mode I fracture toughness was obtained. In the case of non-uniform adhesively bonded joints, the stable crack growth sections and unstable crack growth section were shown. The fracture characteristics of each section were observed through the load-displacement curve of the DCB test and the fracture surface of the specimen. Finite Element Analysis was performed at the section based on segmented section by crack length measured through the test and using the mode I fracture toughness of each section. Through DCB test results and finite element analysis results, it was confirmed that the fracture behavior of specimens with non-uniform adhesion can be simulated.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.26 no.4
• /
• pp.67-80
• /
• 1989

This Paper is concerned with the fracture behavoir of Unidirectional Laminate(UD) and the characteristic length of Multidirectional Laminate(MD) around hole under the Uniform Tensial Strain. Two fracture mechanical concepts of the Waddoups-Eisenman-Kaminski(WEK) model based on the Linear Elastic Fracture Mechanics(LEFM) and the Whitney-Nuismer Model based on Point and Average Stress Criteria were applied. The characteristic length of a laminate with a hole is then obtained using the coefficient of stress reduction and the experimental results, and it can be utilized in predicting the stress level at which the specimen will fracture. The results of the fracture characteristics and the strength of the specimens having a hole in the center can be used as the important experimental data in the research branch of the mechanical fastening of laminated structures. The Ultrasonic scanning and the Acoustic Emission(AE) method were utilized in order to find out the initial defects and the fracture behavior, respectively.