• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.6
• /
• pp.466-468
• /
• 2009

The metal-insulator-silicon (MIS) capacitors with $SiO_2$ and high-k dielectrics ($HfO_2$, $Al_2O_3$) were fabricated, and the current-voltage characteristics were investigated. Especially, an effective barrier height between metal gate and dielectric was extracted by using Fowler-Nordheim (FN) plot and Direct Tunneling (DT) plot of quantum mechanical(QM) modeling. The calculated barrier heights of thermal $SiO_2$, ALD $SiO_2$, $HfO_2$ and $Al_2O_3$ are 3.35 eV, 0.6 eV, 1.75 eV, and 2.65 eV, respectively. Therefore, the performance of non-volatile memory devices can be improved by using engineered tunnel barrier which is considered effective barrier height of high-k materials.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1867-1869
• /
• 1999

Pulse electric field induced electron emission from ferroelectrics has been studied with Pb$(Zr_xTi_{1-x})O_3$ ceramics with varying Zr/Ti ratio from 35/65 to 65/35, Electron emission was proved to be concentrated on the electrode edge by emission profile test and emission capture photographs. The 65/35 composition showed largest emission charge in lowest field and lowest emission threshold field. The emission characteristics are closely dependent on their ferroelectric properties in hysteresis curve. Electron emission charge increases with the polarization charge and emission threshold voltage is dependent on coercive field regardless of their composition. But dielectric constant has little relation with emission property. Electron emission charge increases exponentially with pulse electric field irrespective of composition. On the assumption that the surface potential is linear with the pulse electric field, electron emission can be regarded as a field emission at the electrode edge using Fowler-Nordheim plot of ln$(Q_e/E_{fe})$ to $1/E_{fe}$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.576-576
• /
• 2012

High quality single crystalline strain controlled wurtzite ZnO nanowire arrays have been grown on conductive silicon and ITO substrates by a facile hydrothermal method. The diameter of the nanowires was found to be less than 90 nm approximately for both of the two kinds of substrates. The quality of the ZnO nanowire arrays is dramatically improved by hanging the substrate above from the bottom of the Teflon lined autoclave. The structural investigation indicates the preferential orientation of the nanowire along c-axis. In order to make the convincible comparison, the photoluminescence property of the nanowire arrays grown under different conditions are measured, the sharp near band edge emission from PL, low turn-on voltage ($1.9V/{\mu}m$) from field emission measurement and Fowler-Nordheim plot was investigated from ZnO nanowire arrays grown by proposed substrate hanging method.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.4
• /
• pp.231-237
• /
• 2018

In this study, two important requirements for the home production of a robot to detect and remove improvised explosive devices (IEDs) are presented in terms of the total cost for robot system development and the performance improvement of the mine detection technology. Firstly, cost analyses were performed in order to provide a reasonable solution following an engineering estimate method. As a result, the total cost for a mass production system without the mine detection system was estimated to be approximately 396 million won. For the case including the mine detection system, the total cost was estimated to be approximately 411 million won, in which labor costs and overhead charges were slightly increased and the material costs for the mine detection system were negligible. Secondly, a method for fabricating the carbon nanotube (CNT) based gas detection sensor was studied. The detection electrodes were formed by a photolithography process using a photosensitive CNT paste. As a result, this method was shown to be a scalable and expandable technology for producing excellent mine detection sensors. In particular, it was found that surface treatments by using adhesive taping or ion beam bombardment methods are effective for exposing the CNTs to the ambient air environment. Fowler-Nordheim (F-N) plots were obtained from the electron-emission characteristics of the surface treated CNT paste. The F-N plot suggests that sufficient electrons are available for transport between CNT surfaces and chemical molecules, which will make an effective chemiresistive sensor for the advanced IED detection system.