• Journal of Korea Foundry Society
• /
• v.21 no.3
• /
• pp.163-178
• /
• 2001

The squeeze infiltration process is potentially of considerable industrial importance. The performance enhancements resulting from incorporation of short alumina fiber into aluminum are well documented. These are particularly significant for certain automobile components. Aluminum matrix composite automotive parts, such as diesel engine pistons or engine blocks are produced using squeeze casting apparatus or pressure die-casting apparatus. But the solidification process gets complicated with manufacturing parameters and the factors for porosity formation have not fully understood yet. In this study the formation of porosity during squeeze infiltration has been studied experimentally to achieve an improved understanding of the squeeze infiltration process for manufacture of short-fiber-reinforced components, particularly the mechanism of porosity formation. Al-based MMCs produced under a range of conditions were examined metallographically and the porosity characterised;a kind of matrix, an initial temperature of melt, and a volume fraction of reinforcement. The densimetry and the microscopic image analysis were done to measure the amount of porosity. A correlation between manufacturing parameters and defects was investigated through these.

• Journal of Korea Foundry Society
• /
• v.34 no.3
• /
• pp.107-111
• /
• 2014

Permeability is the ability of a material to transmit fluid/gases. It is an important material property and it depends on mould parameters such as grain fineness number, clay, moisture, mulling time, and hardness. Modeling the relationships among these variable and interactions by mathematical models is complex. Hence a biologically inspired artificial neural-network technique with a back-propagation-learning algorithm was developed to estimate the permeability of green sand. The developed model was used to perform a sensitivity analysis to estimate permeability. The individual as well as the combined influence of mould parameters on permeability were simulated. The model was able to describe the complex relationships in the system. The optimum process window for maximum permeability was obtained as 8.75-10.5% clay and 3.9-9.5% moisture. The developed model is very useful in understanding various interactions between inputs and their effects on permeability.

• Journal of Korea Foundry Society
• /
• v.28 no.5
• /
• pp.231-236
• /
• 2008

H-NCM(Hong-Nanocast Method)has several benefits such as a lower porosity defect and high quality casting comparing to conventional die casting. Influence of casting parameters of hybrid-lower arm in rheocasting process on the slurry flow and the amount of porosity defect was investigated using experimental and simulation methods. In the present study, the Carreau model was adopted to simulate the pattern of rheological flow. Optimal casting paremeters such as injection speed and stroke variations were established. Sound products with integral microstructure and sound shape of joinning different materials of Al and steel pipe without deforming the steel pipe were obtained by the H-NCM slurry and X-ray analysis also showed integral condition throughout the entire parts.

• Journal of Korea Foundry Society
• /
• v.29 no.4
• /
• pp.181-186
• /
• 2009

The interrelationship between new parameter ${\sigma}$ and maximum diameter $D_{max}$ is elaborated and discussed in comparison with four other glass forming ability (GFA) parameters, i.e. (1) super-cooled liquid region ${\Delta}T_x (=T_x - T_g)$, (2) reduced glass transition temperature $T_{rg} (=T_g/T_l)$, (3) K parameter $K (=[T_x-T_g]/[T_l -T_x])$, and (4) gamma parameter ${\gamma}(=[T_x]/[T_l+T_g])$ in Ca-based bulk metallic glass (BMG) systems. The ${\sigma}$ parameter, defined as ${\Delta}T^*{\times}P^'$, has a far better correlation with $D_{max}$ than the GFA parameters suggested so far, clearly indicating that the liquid phase stability and atomic size mismatch dominantly affect the GFA of Ca-based BMGs. Thus, it can be understood that the GFA of BMGs can be properly described by considering structural aspects for glass formation as well as thermodynamic and kinetic aspects for glass formation.

• Journal of Korea Foundry Society
• /
• v.42 no.1
• /
• pp.3-11
• /
• 2022

In this study, the parameters on the shrinkage defect of HR3C alloy was secured through computer simulation research, and the ingot mold with greater than 85% of sound area was designed and manufactured. Moreover, the optimized coagulation was proposed at design stage through computer simulation and test was performed upon ingot manufactured. After the test, the defect pattern was analyzed through cutting and non-destructive inspection to verify the parameter and ingot mold design. Based on the verification results, shrinkage defect parameters such as Niyama, Feed Efficiency, and Hot Tear Intensity of HR3C Alloys were obtained. In addition, through the secured parameters, a plan for designing ingot mold with a Non-defect area of 85% or more was secured.

• Journal of Korea Foundry Society
• /
• v.15 no.2
• /
• pp.184-193
• /
• 1995

Effects of process parameters during thixocasting, such as solid volume fraction, mold temperature and extrusion ratio, on the mold filling behaviour and fluidity of Mg alloy(AZ91D) have been investigated. The semi-solid ingot held for 60 minutes at the semi-solid temperature range did not contain the equilibrium volume fraction of solid as expected from the phase diagram. Therefore, in order to obtain the desired solid fractions, and to suppress the exaggerated grain growth during heating, it was required to heat the ingot rapidly up to the temperature $10^{\circ}C$ higher than the semi-solid temperature suggested from the phase diagram for a specific volume fraction of solid. The experimental results show that mold filling behaviour and fluidity can be improved with the use of the higher mold temperature and the lower volume fraction of solid, but remain nearly unaffected by the change of extrusion ratio.

• Journal of Korea Foundry Society
• /
• v.24 no.4
• /
• pp.238-248
• /
• 2004

고압 다이캐스팅에서 요구되고 있는 고품질의 주조를 위해, 비교적 간단한 개선 방안으로 용탕 주입 방법의 개선이 실험적으로 시도 되었으며, 그로 인해 많은 경우에 긍정적인 결과가 관찰 되었다. 특히, 냉가압 다이캐스트에서, 금형내 용탕의 예충전을 유도하는 용탕 주입의 속도 및 플렌저의 위치제어를 통해 기공율의 저하 및 그로 인한 기계적 강도의 개선 효과를 확인 할 수 있었다. 본 논문은, 그 원인과 결과 대한 연구를 위해, 상용 해석 도구인 Flow3D를 이용, 금형내 용탕의 흐름을 모델링을 통해 가시화하여 용탕의 주입속도 및 위치의 변화가 주물의 품질에 미치는 영향을 조사하였다. 용탕 주입을 위한 플런저의 속도 및 위치 제어의 변수로, 1) 금형내에 용탕의 예충전 유도를 위한 용탕 고속 주입 지연 정도, 2) 플런저의 저속운행에서 고속으로의 가속도, 3) 용탕의 예충전 동안의 플런저 속도를 선택, 그로 인한 영향을 연구 분석 하였고, 그 결과로 플런저의 속도 및 위치 조절을 통하여 금형내 갇힌 공기의 양이 줄어 들 수 있음을 알 수 있었다.

• Journal of Korea Foundry Society
• /
• v.17 no.6
• /
• pp.598-607
• /
• 1997

Fractional melting process involves heating an alloy within its liquid-solid region simultaneously ejecting liquid from the solid-liquid mixture. The extent of the purification obtained is comparable to that obtained in multi-pass zone refining. The new fractional melting process in which centrifugal force was used for separating the liquid from the mixture has been developed and applied to the purification of the metallic grade. Refining ratio depends on partition ratio, cake wetness and diffusion in the solid, and it was controlled by various processing parameters such as rotating speed and heating rate. The new parameter called "refining partition coefficient" has been suggested to estimate the effects of processing variables on the refining ratio. Because major impurities in MG-silicon such as Fe, Al, Ni have a low segregation coefficient, good purification effect is expected. The results of refining MG-silicon(98%) showed that 3N-Si was obtained in refined solid of 50% of the original sample.

• Journal of Korea Foundry Society
• /
• v.9 no.1
• /
• pp.67-72
• /
• 1989

Solidification analysis was conducted on large steel castings and ingots by a modified finite difference method. Auto-mesh generation system was developed for improving the application of the computer analysis system to casting disign. Combined use of the prediction parameters, solidification time and temperature gradient, and an auxiliary parameter, shrinkage potential, were used to predict the formation of shrinkage defects. Several examples on the prediction of shrinkage cavity by this method were campared with the experimental reslts. It was found that a quantitative design of large steel castings and ingots can be made by the computer aided analysis of solidification process.

• Journal of Korea Foundry Society
• /
• v.15 no.4
• /
• pp.408-415
• /
• 1995

Polycrystalline Al-Cu ribbons were produced by planar flow casting(PFC). Solidification behavior and microstructual changes of the ribbons have been investigated as a function of ribbon thickness and processing parameters. The solidification front velocity, V varies within the ribbon, decreasing with increasing the distance, S from the wheel-contact surface, as $V=17.6S^{-1}$. In Al-4.5wt%Cu alloy, rapid decrease in solidification velocity toward the free surface causes a change in solidification morphology from planar to cellular, and finally, to dendritic. The length and inclination of columnar grains solidified with planar front were related to the wheel velocity. The transition from particulate degenerate eutectic structure to regular lamellar eutectic structure was observed to be caused by a difference of the relative growth velocites of ${\alpha}-Al$ and ${\theta}$ during solidification in the Al-Cu eutectic alloy.