• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1994년도 춘계학술대회 논문집
• /
• pp.92-100
• /
• 1994

Forming limit diagrams for three different galvanized deep drawing quality steel sheets have been measured by hemispherical punch stretching. The experimental forming limit diagrams have been compared with results calculated using the shear instability criterion and the M-K model which takes into account a strain gradient effect resulting from bending (curvature) of a flat sheet by punch stretching. The measured data were in good agreement with the results calculated using exponent M value of 8 in Hosford's yield criterion for the M-K model and M= 6 for the shear instability model.

• Journal of Mechanical Science and Technology
• /
• 제15권2호
• /
• pp.210-216
• /
• 2001

This paper presents an analytical study that can predict the path-dependent forming limit of anisotropic sheet materials that experience various combinations of strain paths. To predict the forming limit diagrams(FLD), the proposed analytical procedure is performed within the framework of the Marciniak and Kuczynski(M-K) approach by using the Barlat and Lians non-quadratic anisotropic yield criterion and introducing the effect of the existence of a strain gradient over a stretching punch. The predicted path-dependent forming limit of an anisotropic sheet has been compared with the published experimental results. It has been found that the predicted path-dependent forming limits are in good agreement with the experimental data.

• 소성∙가공
• /
• 제33권2호
• /
• pp.87-95
• /
• 2024

The current study aims to prove that high-speed forming has better formability than conventional low-speed forming. Experimentally, the quasi-static forming limit diagram was obtained by Nakajima test, and the dynamic forming limit diagram was measured by electrohydraulic forming. For the experiments, the LS-DYNA was used to create the optimal specimen for electrohydraulic forming. The strain measurement was performed using the ARGUS, and comparison of the forming limit diagrams confirmed that EHF showed better formability than quasi-static forming. Theoretically, the Marciniak-Kuczynski model was used to calculate the theoretical forming limit. Swift hardening function and Cowper Symonds model were applied to predict the forming limits in quasi-static and dynamic status numerically.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 춘계학술대회논문집
• /
• pp.222-225
• /
• 1997

This paper describes experimental investigation on the forming limit for mash-seam welded sheets. The uniaxial tensile test was conducted to evaluate the mechanical properties of weld bead. Experimental forming limit diagrams were investigated for the different thicknesses and properties of welded sheets.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 추계학술대회 논문집
• /
• pp.109-112
• /
• 2000

This paper presents an analytical study that can predict the path-dependent forming limits for bilinear strain paths. To predict the forming limit diagrams(FLD), the analytical procedure was performed within the framework of Marciniak and Kuczynski approach by introducing the effect of the existence of strain gradient over the stretching punch. The predicted path-dependent forming limits of an anisotropic sheet were compared with the published experimental results. It was found that the predicted path-dependent forming limits were in good agreement with the experimental data.

• 소성∙가공
• /
• 제6권4호
• /
• pp.300-310
• /
• 1997

A finite element inverse method is introduced for direct prediction of blank shapes, strain distributions, and reliable intermediate shapes from desired final shapes in axisymmetric multi-step deep drawing processes. This mothod enables the determination of process disign. The approach deals with the Hencky's deformation theory. Hill's second order yield criterion, simplified boundary conditions, and minimization of plastic work with constraints. The algorithm developed is applied to motor case forming, and cylindrical cup drawing with the large limit drawing ratio so that it confirms its validity by demonstrating resonably accurate numerical results of each problem. Numerical examples reveal the reason of difficulties in motor case forming with corresponding limit diagrams.

• 소성∙가공
• /
• 제7권1호
• /
• pp.81-93
• /
• 1998

Identification of forming limits of sheet metals is an important task to be done before the sheet metal forming processes. The information of the forming limit is indispensable for design of deformed shapes and related forming processes. This procedure becomes more important than ever as the auto-body becomes complicated and the number of auto-body parts is reduced for lower production cost. To identify the forming limit of sheet metals stretching with a hemispherical punch has gained popularity because of the convenient experimental procedure. The stretching experiment however has localized deformation or the shear band is originated from the non-unifrom deformation in the critical circum-stance instead of the absolute criterion. More accurate information of the forming limit therefore could be obtained by a more appropriate experiment to the real process. In this papaer an experiment program is devised to practivally identify the forming limits of sheet metals for auto-body parts. The experiment program contains not only stretching but deep-drawing Both forming experiments use the same hemispherical punch while they use different specimens. Deep-drawing experiments use speci-mens cut out in circular arc on both sides of circular blank to make it torn during the deep-drawing They also use speciments cut out straight in one side of a circular blank to make it deformed unevenly which causes local deformation during the deep-drawing. The experimental result demonstrates that the forming limit diagrams in the two cases show difference in their effective magnitude. The forming limit curve from deep-drawing is located lower than that from stretching. It is noted from the result that the deep-drawing process causes acceleration of localized deformation in comparison with the stretching process. From the experimental result the maximum value of forming limit could be pre-dicted for safe design.

• 소성∙가공
• /
• 제23권6호
• /
• pp.351-356
• /
• 2014

The current study aims to predict the forming limits considering the deformation characteristics of tailor rolled blank(TRB) during hot stamping. The formability of TRB is affected by the TRB line orientation because elongations change due to the intrinsic geometry within the sheet. To evaluate the forming limits, Nakazima tests were conducted at elevated temperatures with different TRB line orientations. Forming limit diagrams(FLD) of TRB can be predicted by an interpolating equation based on the Nakazima test. Predicted FLDs were used in FE-simulations of a rectangular drawing. The predicted limit drawing height was compared with experimental results. The simulation results show good agreement with the experimental ones with an error range of 3%.

• 소성∙가공
• /
• 제23권4호
• /
• pp.199-205
• /
• 2014

The current study examines the effect of the analytical parameter values on the theoretical forming limit diagram (FLD) based on the Marciniak-Kuczynski model (M-K model). Tensile tests were performed to obtain stress-strain curves and determine the anisotropic properties in the rolling, transverse and diagonal direction of SPCC sheet materials. The experimental forming limit curve for SPCC sheet material was obtained by limiting dome stretching tests. To predict the theoretical FLD based on the M-K model, the Hosford 79 yield function was employed. The effects of three analytical parameters - the exponent of the yield function, the initial imperfection parameter and the fracture criterion parameter - on the M-K model, were examined and the results of the theoretical FLD were compared to the experimentally measured FLD. It was found that the various analytical parameters should be carefully considered to reasonably predict the theoretical FLD. The comparison of the acceptable forming limit area between the theoretical and experimental FLD is used to compare the two diagrams.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1994년도 박판성형기술의 진보
• /
• pp.173-184
• /
• 1994

A method of obtaining deformation severity of axisymmetric shape deep-drawn products was developed. Strain states of products produced by single or multi-stage drawing were predicted by using finite element analysis. This method used minimization of potential energy between the known shape of final product and the unknown in initial blank. And that was done numerically by nonlinear finite element method. Deformation theory of plasticity was used for practical purposes. From predicted strain states of drawn parts, deformation severity was found by using forming limit diagrams.