• 소성∙가공
• /
• 제27권3호
• /
• pp.160-164
• /
• 2018

The success of warm forming of Mg alloy sheets is very dependent on its frictional behavior at elevated temperatures. The effects of contact pressure and sliding length on the frictional characteristics of AZ31B Mg alloy sheet were investigated at elevated temperature and at room temperature. The contact pressure range for the friction test was determined through FE analysis of the roof panel which is a candidate for Mg alloy application. According to the experimental results, the frictional behavior of the Mg alloy sheet is equally highly influenced by both sliding length and contact pressure at room temperature. At elevated temperatures, however, the sliding length has a more dominant influence on the frictional characteristics of the Mg alloy sheet than the contact pressure, if the contact pressure is lower than a certain level.

• ALGAE
• /
• 제18권4호
• /
• pp.295-299
• /
• 2003

The population dynamics of Ecklonia stolonifera was investigated at Tongyeong coastal area in the South Sea of Korea. The blade length and width, stipe length and diameter, mean total length and mean weight were measured from randomly collected fifty individuals in every month. The plants in Tongyeong population were relatively bigger than those of Busan Korea and Aomori Japan in terms of their blade length and width. The population biomass was low in winter and high in spring and summer. The sporangial sori were found from August to December but prominent in September and October. About 90 % of the Tongyeong population was consisted of one- and two-year old plants and the zoosporangial sori were observed mostly in two-year old plants. It was different from the results of Busan and Aomori population in which the zoosporangial sori were observed from the plants older than three years. The new populations were developed from the zoospores of two-year old plants and their generation time was relatively shorter than those of Busan and Aomori.

• 반도체디스플레이기술학회지
• /
• 제8권2호
• /
• pp.43-47
• /
• 2009

Glass forming technology is used to form channels of external electrode flat fluorescent lamps (FFL). The efficiency of FFL depends on the number and the length of the channels. Five FFLs with same size ($300\;mm{\times}80\;mm$), different channel number, and different channel length were fabricated. The electrical and optical characteristics of 5 FFLs were evaluated. It was found that the FFL with one channel with its channel length of 1,110 mm and channel width of 7 mm corner width was shown to have the highest efficiency at room temperature operation.

• 건축역사연구
• /
• 제26권4호
• /
• pp.35-44
• /
• 2017

The purpose of this study is to classify three-Kan hipped and gable-roofed Buddhist temples with the construction of their eave curve of part chunyeo and examine the characteristics and causes. The conclusions have been drawn as follows: First, there are largely three ways to secure symmetry in eave curve of part chunyeo. One is to obtain symmetry in eave curve of part chunyeo by making the size of eaves curves on well sides the same and forming symmetric curves in the front section along with the side roof and then forming the straight line in the central part (hereinafter referred to as the long straight line section method). The second is a method to enlarge eaves curves in the front and form eaves curves on the roof section to be symmetric (hereinafter referred to as the front is larger than side eaves curves method). The third is the method to make eaves curves in the roof section to be symmetric by adjusting the roof length and making difference between the front and side roof's length minimum (hereinafter referred to as the roof length-controlling method). Second, there are 16 cases applying two or more methods, and they are the mainstream. Third, there are 12 cases applying the front is larger than side eaves curve method and roof length-controlling method both, which seems to be the most universal. To sum up, they secured symmetry in roof edges considering the construction of seonjayeon and pyeongyeon according to the size of the structure, recognition on the directions of entrance into the area of the building, forms of planes, harmony with structures around, recognition on roof curves in accordance with the size, and also structural faults in the chunyeo part.

• Progress in Superconductivity
• /
• 제7권2호
• /
• pp.174-178
• /
• 2006

For the practical application on SCFCL, Bi2212 tubes were fabricated by Centrifugal Forming Process (CFP) in terms of many different processing parameters. Typical sizes of tubes were 60, 150 mm in length and 2.5, 3.5, 4.8 mm in thickness. Initially powder was melted by induction heating. The optimum range of melting temperatures and preheating temperature were $1100^{\circ}C$ and $500^{\circ}C$ for 30min respectively. The nominal mold rotating speed was around 1000 RPM. A tube was annealed at $840^{\circ}C$ for 80 hours in oxygen atmosphere. The tube of 50mm x 70mm x 2.5mm, rotated with 1000 RPM showed $I_c=890\;A\;and\;T_c=80$. It was found that the tube processed with faster rate of mold rotation speed, thinner tube thickness and shorter tube length shows better electric characteristics as compared with the tube normally processed. In order to study the uniformity heat and fluid flow analysis tool was adopted along tube.

• Journal of the Korean Wood Science and Technology
• /
• 제13권3호
• /
• pp.3-26
• /
• 1985

The object of this study was to investigate the effects on physical and mechanical properties of wood particle and sawdust board combined with wire net. Conventional forming, press-lam, and veneer comply boards combining one to four wire net sheets were made from wood particle and sawdust with different spacings (8, 10, 12, and 18 Mok) and different wire diameters (0.35, 0.50, and 0.80mm) composing wire net. They were compared and analyzed statistically with specific gravity, thickness swelling, length swelling, bending properties (modulus of rupture, modulus of elasticity, work to proportional limit, and total work), internal bonding strength, and screw holding strength between wood particle and sawdust boards. The results obtained at this study as cording to the discussions might be concluded as follows; 1. In specific gravity, both particle and sawdust boards by press-lam method were higher than by conventional forming and veneer comply method, and the boards containing more wire net sheets also showed higher value. But the wire net spacings(Mok) had no influence on specific gravity. In general, particle board showed higher specific gravity than sawdust board. Veneer comply board showed lowest specific gravity values. 2. Both particle and sawdust boards by press-lam method was slightly lower than by conventional forming and veneer comply method in thickness swelling. The sawdust board containing 8, 12. and 18 Mok wire net showed lower thickness swelling than the corresponding particle board, but both sawdust and particle boards containing the T8 and 10 Mok wire net showed higher and similar thickness swelling. 3. Both particle and sawdust boards containing wire net showed no difference in MOR and MOE of bending. Comply board was the highest and particle board showed slightly higher than sawdust board in MOR and MOE values. 4. In work to proportional limit and total work in bending, both particle and sawdust boards containing thicker wire diameter and more wire net sheets showed higher value. From these facts, it is conceivable that boards with thicker wire diameter and more wire net sheets show increasing resistance against external force. But there was no significant difference between particle and sawdust borads. 5. In resistance against delamination (internal bonding strength), both sawdust and particle boards containing wire net showed lower value than control, and also showed decreasing tendency with more number of wire net sheet composed. Particle board showed higher resistance against delamination than sawdust board. 6. In screw holding strength, sawdust board containing thicker wire diameter and more wire net sheets showed higher value, but particle board by press-lam method was higher than by conventional forming and veneer comply method. Screw holding strength of particle board was higher than that of sawdust board.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.347-350
• /
• 2004

In this paper, the acceleration is studied for the rigid-plastic FEM of metal forming simulation. In the FEM, the direct iteration and Newton-Raphson iteration are applied to obtain the initial solution and accurate solution respectively. In general, the acceleration scheme for the direct iteration is not used. In this paper, an Aitken accelerator is applied to the direct iteration. In the modified Newton-Raphson iteration, the step length or the deceleration coefficient is used for the fast and robust convergence. The step length can be determined by using the accelerator. The numerical experiments have been performed for the comparisons. The faster convergence is obtained with the acceleration in the direct and Newton-Raphson iterations.

• Journal of Mechanical Science and Technology
• /
• 제20권5호
• /
• pp.621-633
• /
• 2006

To reflect the size effect of material $(1\sim15{\mu}m)$ during plastic deformation of polycrystalline copper, a constitutive equation which includes the strain gradient plasticity theory and intrinsic material length model is coupled with the finite element analysis and applied to plane strain deformation problem. The method of least square has been used to calculate the strain gradient at each element during deformation and the effect of distributed force on the strain gradient is investigated as well. It shows when material size is less than the intrinsic material length $(1.54{\mu}m)$, its deformation behavior is quite different compared with that computed from the conventional plasticity. The generation of strain gradient is greatly suppressed, but it appears again as the material size increases. Results also reveal that the strain gradient leads to deformation hardening. The distributed force plays a role to amplify the strain gradient distribution.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.1
• /
• pp.527-530
• /
• 2004

High-temperature Superconductor(HTS) tubes were fabricated in term of different diameter, length and thickness by centrigugal forming method. For powder melting by induction the optimum range of melting temperatures and preheating temperature were $1050^{\circ}C{\sim}1100^{\circ}C\;amd\;550^{\circ}C$ for 30min, respectively. The mould renting speed was 1000rpm. A tube was annealed at $840^{\circ}C$ for 72hours in oxygen atmosphere. The plate-like grains were well developed along the renting direction and typical grain size was about more than $40{\mu}m$. It was found that Ic values increased with increasing the tube diameter while the Ic decreased with increasing tube thickness. Also Ic decreased with increasing the tube length. The measured Ic in $50mm{\times}70mm{\times}25mm$ tube was about 896Amp.

• 한국산학기술학회논문지
• /
• 제10권11호
• /
• pp.3137-3143
• /
• 2009

본 논문에서는 한팔 나선 안테나(single arm spiral antenna)의 편파(polarization) 및 빔 틸트(beam tilt) 특성에 대하여 분석하였다. 한팔 나선 안테나는 나선 둘레 길이(spiral circumference length)가 한 파장 길이 이상 길어지면, 안테나의 최대방사 빔 방향이 안테나로부터 수직인 축빔(axial beam)으로부터 틸트되는 특성을 가지고 있다. 이때 나선 안테나의 급전위치(내부, 외부)에 따라 원형편파 (RHCP, LHCP)가 변화 하며, 안테나의 길이 변화에 따른 빔 틸트시 원형편파 특성에 따라 최대 방사 빔 방향이 서로 상이한 방향으로 틸트 됨을 검증하였다. 이러한 한팔 나선 안테나의 전기적인 특징을 이용하여, 단일 안테나로 이중 편파를 갖는 빔 포밍, 다이버시티, 또는 MIMO어플리케이션에 대한 적용 가능성을 확인하였다.