• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.555-559
• /
• 2001

Feed and spindle motor currents are used toi monitor the cutting process practically. The sensitivity of spindle drive system is lower than that of feed drive system, but the cutting torque is represented well by the spindle motor current. During multi-axis cutting, it is difficult to calculate the resultant cutting force using feed motor currents, because each feed force is reflected by each axis feed motor current with different time delay. It is also difficult to compensate the frictional torque using the feed motor current, because the magnitude of the frictional torque is dependent of the feedrate, table position, and cutting direction. On the other hand, cutting torque can be estimated well using spindle motor current which is independent of the cutting direction.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.4
• /
• pp.93-100
• /
• 2002

The current from the feed motor of a machine tool contains substantial information about the machining state. There have been many researches that investigated the current as a measure for the cutting farces. However it has been reported that this indirect measurement of the cutting farces from the feed motor current is only feasible in low frequency. In this research, it was presented that the bandwidth of the current monitoring can be expanded to 130 Hz. And the unusual behavior of the current was examined in this bandwidth. The cross-feed directional cutting force influences the machined surface of the workpiece, which makes it necessary to estimate this force to control the roughness of the machined sulfate. The current exists in the stationary feed motor, and it can give the useful information on the quality of the machined surface. But the unpredictable behavior of the current prevents applying the current to prediction of the cutting state. Empirical approach was conducted to resolve the problem. As a result, the current was shown to be related to the accumulation of the accumulation of the infinitesimal rotation of the motor. rotation of the motor. Subsequently the relationship between the current and the cutting force was identified.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.30 no.2
• /
• pp.26-30
• /
• 2016

This paper presented an optimum design of a perpendicular PMDSLSM (Permanent Magnet Double-sided Linear Synchronous Motor) to minimize the detent force. As an optimum method, the response surface method was used and 3D finite element method for the calculation. The design variables of the machine were the primary core width and thickness, and magnet width, thickness and length. Object functions were to minimize the detent force and maximize the thrust of the basic model. The results showed that the thrust force of the optimum design increased from 82.1N to 90.2N and detent force decreased from 15.2N to 2.8N, respectively, compared to the basic model.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.722-726
• /
• 2007

In this paper we deal with a design of the integral sliding mode controller to suppress the disturbance force acting on the suspension system of the magnetically levitated train system. One of the important factors that cause the disturbance force acting on the suspension system comes from the low propulsion speed of linear induction motor. In this paper integral sliding mode controller is employed to reject the disturbance force produced by the propulsion system of the linear induction motor. In order to show the effectiveness of the designed controller a dynamic simulation is utilized and the sliding mode controller without integral compensator is compared with the proposed integral sliding mode controller to suppress the disturbance force.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.4
• /
• pp.1667-1673
• /
• 2015

The vibration and noise caused by the dynamic interaction between electromagnetic suspension and the linear synchronous motor stator beneath a flexible guideway remain problems in designing attractive Maglev trains. One possible method to reduce the sources of vibration is to minimize the detent force in the linear synchronous motor that creates variations in both lift force and thrust. This paper proposes lowering detent force by using separated core instead of single united core. The magnet is designed to adapt to the deflected guideway at a speed of 550km/h. This study will analyze the electromagnetic field and control performance, and how they relate to lift forces and dynamic responses.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.65.6-65
• /
• 2002

In teleoperation robotic system such as hydraulically actuated robotic excavator for dangerous area, the maneuverability and convenience is the most important part. Particularly the force information is important in dealing with digging and leveling operation in the tole-operated excavator. Excavators are also subject to a wide variation of soil-tool interaction forces. This paper proposes a new force reflecting joystick using pneumatic motor and a new algorithm for selecting force-reflecting gain in a velocity-force type bi lateral teleoperation system. The master system is electrical joystick with the same structure of that of real excavator. Particularly Pneumatic motor is used newly in...

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.11
• /
• pp.1733-1740
• /
• 2004

In the transverse flux linear induction motor(TFLIM) with the general secondary composed of conductor and back-yoke, there exists a magnetized force into the normal direction or the air-gap direction of the thrust motion as well as the thrust force. Therefore, the various methodologies have been tried to use the normal force by the two independent control variables of the multi-phase input. But, as the force depends inevitably and strongly on the thrust force, it is essential to decouple both forces for two control index. In this paper, we suggest a novel approach capable of compensating the couple between both forces and the control index by using the DC-biased multi-phase input, and then realizing the independent control of TFLIM.

• Journal of Power Electronics
• /
• v.9 no.6
• /
• pp.845-853
• /
• 2009

This paper presents a novel hybrid pole BLSRM (Bearingless Switched Reluctance Motor) and its radial force control scheme. The proposed hybrid pole BLSRM has separated radial force poles and rotating torque poles. According to the FEM analysis, the proposed BLSRM has an excellent linear characteristic of radial force and controllability that is independent from the torque current. The radial force can be produced by the radial force winding which is wound at the separated radial force poles. The rotating torque is produced by the excitation current of the torque windings which are wound at the torque pole. The proposed radial force control scheme is independent of the phase torque winding current. A simple PID controller and look-up table are used to maintain a constant rotor air-gap. The proposed BLSRM and its radial force control scheme are verified by FEM analysis and experimental tests.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05b
• /
• pp.3-7
• /
• 2003

Usually, the thrust is calculated by magnetic equivalent circuit modelling method for thrust capacity and accuracy progress of position control about a Linear Pulse Motor of which position precision is good and open-loop control is possible within Linear Motors. Analytical thrust deviation exists to calculating magnetic flux density by using Permeance Modelling Method, Finite Element Method, and Velocity Electric Motive Force Method. For calculating accuracy thrust by using these every method, the thrust is calculated and compared by Lorentz Force Method, Magnetic Coenergy Method, and Maxwell correspondence force Method. And that becomes important factor at the comparison of each capacity and parameter of Motor. So this study wants to compare and analyze measurement data and calculating data of the static force of Linear Pulse Motor. and then we can get more accuracy method, calculating the static thrust of Linear Pulse Motor(LPM).

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.4
• /
• pp.385-391
• /
• 2008

To effectively cope with a complexity of kinematic metrology due to workspace enlargement of the planar stage, the linear induction motor is suggested as its new driving source. Especially, the linear induction motor under uniform plate type of secondary doesn't inherently have a periodical force ripple which is generally shown in the brushless DC motor. But, it presents a poor transient characteristic at zero or low speed zone owing to time delay of flux settling, resulting in slow response. To improve the servo property of linear induction motor and apply successfully it to the precision stage, this paper discusses a modified vector control methodology. The controller has a novel input form, fixed d-axis current, q-axis current and forward-fed DC current, to control thrust force and normal force of the linear induction motor independently. Influence of the newly introduced input and the feasibility of controller are validated experimentally.