• Applied Chemistry for Engineering
• /
• v.9 no.2
• /
• pp.278-285
• /
• 1998

In a fixed bed reactor, adsorption capacity of $SO_2$ in simulated flue gases was investigated with NMO(natural manganese ore), composed of various metal oxides, iron ore and $CuO/{\gamma}-Al_2O_3$ as adsorbents. The experiment carried out in a fluidized bed reactor with variables such as gas velocity, temperature and particle size. Iron ore was excluded in the fluidized bed reactor experiment for the lower adsorption capacity. The adsorption of $SO_2$ in metal oxide is a typical chemisorption because the adsorption capacity of all adsorbents increased with temperature. The effect of particle size on the adsorption capacity was varied with the ratio, $U_o/U_{mf}$ and the difference of $U_o-U_{mf}$. $U_o$ is the gas velocity, $U_{mf}$ is the minimum fluidization gas velocity. $U_o/U_{mf}$ and $U_o-U_{mf}$ explain the behavior of the gas and solids in the fluidized bed reactor. From the performance equation of the fluidized bed reactor, kinetic reaction rate constants were obtained by the non-linear least square method. The adsorption capacity of NMO proved the potential use of $SO_2$ adsorbents.

• Journal of Environmental Health Sciences
• /
• v.22 no.1
• /
• pp.82-90
• /
• 1996

The objectives of this study were to examine the start-up method and characteristics of biomass attachment on the media in an anaerobic fluidized bed reactor(AFBR). The media adopted was the granular activated carbon which was successfully capable of adsorbing organics and biomass. The reactor was operated at 5 kg $COD/m^3\cdot day$ and 24hr of HRT. There were important problems in the AFBR's start-up, which has been reported very long and unstable. Therefore, this research was to solve the problem of the start-up and it was performed, comparing two start-up ways that were initial fluidized system and initial static-fluidized system. The results were summarized as follows: (1) On the whole initial static-fluidized system was superior to initial fluidized system in the aspects of biogas production rate, methane content and COD removal efficiency etc. (2) At the steady state methane production rate and recoverable bioenergy of initial static-fluidized system were $2.074 m^3CH_4/m^3\cdot day$, $0.488 m^3CH_4/kgCOD_{removed}\cdot day$, and 81.3kcal/day, respectively. (3) Thickness of biofilm was about $5.11 \mu m$, $\rho_{bw}$ and $\rho_{bd}$ were $1.022 g/cm^3, 0.0953g/cm^3$ respectively. (4) Biomass concentration of fluidized state was about 35 mg/g GAC. In conclusion the efficient method on the start-up of the AFBR using GAC as media was initial static-fluidized system and the period of static state needed to reach steady state was considered about twenty days.

• Journal of Environmental Science International
• /
• v.5 no.3
• /
• pp.361-367
• /
• 1996

An inverse fluidized-bed biofilm reactor (IFBBR) was used for the treatment of highly-emulsified oily wastewater. When the concentration of biomass which was cultivated in the synthetic wastewater reached to 6000 mg/1, the oily wastewater was employed to the reactor with a input COD concentration range of 50 mg/1 to 1900 mg/l. Virtually the IFBBR showed a high stability during the long operation period although soma fluctuation was observed. The COD removal efficiency was maintained over 9% under the condition that organic loading rate should be controlled under the value of 1.5 kgCOD/$m^3$/day, and F/M ratio is 1.0 kgCOD/kgVSS/day at $22{\circ}C$ and HRT of 12 hrs. As increasing organic loading rates, the biomass concentration was decreased steadily with decreasing of biofilm dry density rather than biofilm thickness. Based on the experimental jesuits, it was suggested that the decrease in biofilm dry density was caused by a loss of biomass inside the biofilm.

• Journal of Environmental Science International
• /
• v.4 no.3
• /
• pp.221-228
• /
• 1995

Stability of reactor and effect on biofilm characteristics were investigated by varying the hydraulic residence time in an inverse fluidized bed biofilm reactor(IFBBR). The SCOD removal efficiency was maintained above 90 % in the HRT range of 12hr to 2hr, but the TCOD removal efficiency was dropped down to 50% because of biomass detachment from overgrown bioparticles. The reactor was stably operated up to the conditions of HRT of 2hr and F/M ratio of 4.5kgCOD/$m^3$/day, but above the range there was an abrupt increase of filamentous microorganisms. The optimum biofilm thickness and the biofilm dry density in this experiment were shown as $200\mu\textrm{m}$ and $0.08 g/cm^3$, respectively. The substrate removal rate of this system was found as 1st order because the biofilm was maintained slightly thin by the increased hydraulic loading rate.

• Membrane Journal
• /
• v.28 no.4
• /
• pp.252-259
• /
• 2018

An acidic, real metal-plating wastewater was treated by a fluidized bed membrane reactor introduced with granular activated carbon (GAC) as fluidized media. With GAC fluidization, there was no increase in suction pressure with time at each flux set-point applied. At neutral solution pH, much less fouling rate was observed than acidic pH under GAC fluidization. Higher solution pH resulted in the increase in particle size in metal-finishing wastewater, thus producing a less dense cake structure on membrane. More than 95% of chemical oxygen demand was observed from the fluidized bed membrane reactor under GAC fluidization. Total suspended solid concentration in membrane permeate was near zero. At the raw wastewater pH, no removal of copper and chromium by the fluidized bed membrane reactor was observed. As the pH was increased to 7.0, removal efficiency of copper and chromium was increased considerably to 99 and 94%, respectively. Regardless of solution pH tested, more than 95% of cyanide was removed possibly due to the strong adsorption of organic-cyanide complex on GAC in fluidized bed membrane reactor.

• Journal of Environmental Health Sciences
• /
• v.24 no.2
• /
• pp.57-67
• /
• 1998

The characteristics of anaerobic degradation of phenol were studied in a fluidized bed reactor using a granular activated carbon as media. Increasing the phenol loading rate with variation of feed concentration was considered as an experimental variable. In the present anaerobic fluidized-bed reactor, the removal efficiency of phenol and COD was maintained about 93-99% and 91-96%, respectively, up to 3.6 kg-phenol/$m^3\cdot d$ of the phenol loading rate, but it was abruptly decreased under 5.0 kg-phenol/$m^3\cdot d$. The volumetric production of biogas per removed phenol was decreased linearly between 0.80-1.27 m$^3$ gas/kg-phenol (0.35-0.56 m$^3$-gas/kg-COD), increasing the phenol loading rate, and the methane content of biogas was 55-60% as similar to that estimated theoretically up to 3.6 kg-phenol/$m^3\cdot d$. But the production rate and methane content of biogas were suddenly decreased at the loading rate of 5.0 kg-phenol/$m^3\cdot d$. Therefore, the anaerobically biodegradable phenol loading rate of the present reactor was 3.6 kg-phenol/$m^3\cdot$ d in order to accomplish over 90% of the removal efficiency.

• Journal of the Korean Society of Combustion
• /
• v.13 no.2
• /
• pp.23-32
• /
• 2008

Gasification characteristics in the fluidized bed reactor are essential for the design of a gasification furnace to optimize the operation condition. Moisture content of the solid fuel is one of the important factors to influence directly the gasification characteristics. So it is necessary to investigate the effect of moisture content of solid fuel in partial oxidation condition. Gasification characteristics are investigated with results from thermogravimetric analyzer and lab-scale fluidized bed reactor for wood and RDF samples along with changing moisture contents. Additionally lab-scale fluidized bed reactor was run continuously and gas concentrations at the exit were measured. It is observed that the rate of reaction in partial oxidation condition is between the results from the combustion environment and from the inert condition. Moisture content in a particle slows down the heating rate of a particle. So, reaction is delayed by the moisture content. However, RDF samples those are easy to break-up don't show the effect of moisture content. The result of continuous operation condition shows that proper moisture content promotes gasification because steam from the particles helps gasification of the solid fuel. A simulation to predict the syn-gas composition was conducted by the Aspen Plus process simulator. The cold gas efficiency of the experiment was compared with results from the simulation.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.81-85
• /
• 2007

A fluidized bed reactor is made with quartz. The size of FBR is 0.055 m I.D. and 1.0 m in height. The FBR was employed for the thermocatalytic decomposition of propane to produce hydrogen without $CO_{2}$. The fluidized bed was proposed for the continuous withdraw of product carbons from the reactor. Carbon black DCC-N330 is used to decompose the propane gas. The propane decomposition reaction over carbon black catalyst in a fluidized bed reactor was carried out the temperature range of 600 ${\sim}$ 800 $^{\circ}C$, propane gas velocity of 1.0 ${\sim}$ 4.0$U_{mf}$($1U_{mf}$ = 0.61cm/s) and the catalyst loading of 100 ${\sim}$ 200g. Production of $H_{2}$ such as other reaction temperature, gas velocity, catalytic loading on the reaction rates was investigated. The carbon depositied on the catalyst surface was observed by FE-SEM. The particle size of the carbon black was observed by Particle size analyzer. Resulting production in the experiment was not only hydrogen but also several by-products such as methane, ethylene, ethane, and propylene.

• 한국연소학회:학술대회논문집
• /
• 2007.05a
• /
• pp.161-167
• /
• 2007

Gasification characteristics in the fluidized bed reactor are essential for the design of a gasification furnace to optimize the operation condition. Moisture content of the solid fuel is one of the important factors to influence directly the gasification characteristics. So it is necessary to investigate the effect of moisture content of solid fuel in gasification process. Gasification characteristics are investigated with results from thermogravimetric analyser and lab-scale fluidized bed reactor for wood and RDF samples along with changing moisture contents. Additionally lab-scale fluidized bed reactor was run continuously and gas concentrations at the exit were measured. It is observed that the rate of reaction in partial oxidation condition is in between the results from the combustion environment and from the inert condition. Moisture content in a particle slows down the heating rate of a particle. So, reaction time is delayed by the moisture content. However, RDF samples that are easy to break-up doesn't show the effect of moisture content. The results of continuous operation condition shows that proper moisture content promotes gasification because steam from the particles helps gasifcation of the sold fuel.

• Journal of the Korean Applied Science and Technology
• /
• v.21 no.3
• /
• pp.225-230
• /
• 2004

Synthesis gas is a high valued compound as a basic chemicals at various chemical processes. Synthesis gas is mainly produced commercially by a steam reforming process. However, the process is highly endothermic so that the process is very energy-consuming process. Thus, this study was carried out to produce synthesis gas by the partial oxidation of methane to decrease the energy cost. The effects of reaction temperature and flow rate of reactants on the methane conversion, product selectivity, product ratio, and carbon deposition were investigated with 13wt% Ni/MgO catalyst in a fluidized bed reactor. With the fluidized bed reactor, $CH_4$ conversion was 91%, and Hz and CO selectivities were both 98% at 850$^{\circ}C$ and total flow rate of 100 mL/min. These values were higher than those of fixed bed reactor. From this result, we found that with the use of the fluidized bed reactor it was possible to avoid the disadvantage of fixed bed reactor (explosion) and increase the productivity of synthesis gas.