• 대한토목학회논문집
• /
• 제31권5A호
• /
• pp.389-397
• /
• 2011

본 논문에서는 이방향 휨인장강도 시험 시 시험체에 작용하는 등방성 휨인장거동의 구현여부를 실험적으로 증명하기 위해 시험체의 변형률 측정 실험과, 시험체에 등방성 휨인장응력이 작용할 수 있도록 시험법 개선을 위한 연구를 수행하였다. 또한, 개선된 시험법을 적용하여 이방향 휨인장강도와 4점 휨인장강도 시험에 의한 일방향 휨인장강도를 측정하여 비교하였다. 실험 결과, 시험체에 발생하는 등방성 휨인장응력은 시험체의 표면 조건과 뒤틀림 정도에 많은 영향을 받는 것으로 나타났으나, 시험법 개선으로 인해 시험체에 등방성 휨인장응력상태를 확보할 수 있었다. 개선된 이방향 휨인장강도 시험에 의한 이방향 휨인장강도가 일방향 휨인장강도 보다 32% 더 큰 것으로 나타났으며, 분산성은 동일한 것으로 나타났다.

• 대한치과기공학회지
• /
• 제31권2호
• /
• pp.9-14
• /
• 2009

In this study, to improve the flexure strength of Zirconia, on the Zirconia pellet surface measure the flexure strength to melt or permeate the Alumina (Vita Zahnfabrik, Bad Sachkingen, Germany) of private used In-Cream and observe by Scanning election microscope. In the control group(3Y-TZP group), the average of flexure strength was 1623.7MPa, and in the experimental group(Glass-infiltrated 3Y-TZP group) was 1800.2MPa. As a result of observing the interface between glass and zirconia with a scanning election microscope, it was showed that the glass dissolves to permeate into the surface of zirconia, so filled the zirconia with particles.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 추계학술발표대회 논문집
• /
• pp.119-122
• /
• 2003

This report describes the procedure of detailed design and structural test for the composite flexure which is a part of the hingeless hub system. First, stacking sequence design for composite flexure was done, and structural analysis by using NASTRAN was made to verify structural stability and safety. Using FPS installed at KIMM, composite flexure was laid up and cured using a autoclave. Before rotor ground test, the basic structural tests such as a bench test, tensile strength test and shear strength test, for flexure, were accomplished. Through replacing existing metal hub part with new fabricated composite flexure, improvement of aeroelastic stability and weight reduction were achieved. This result will be applied to composite rotor system design fur helicopter.

• 구강회복응용과학지
• /
• 제23권2호
• /
• pp.119-130
• /
• 2007

Purpose: This investigation was designed to estimate the flexure strength, density, and microstructure of the colored and uncolored zirconia oxide ceramics for fixed partial denture. Material and Methods: LAVATM All Ceramic(3M-ESPE, USA), Cercon Smart Ceramic(Dentsply, USA), and Z-match Ceramic(DentAim, Korea) were used for this study. All specimen was fabricated by ASTM C1161. After preparing $25{\times}2{\times}1.5mm$ of rectangular column and sitting rectangular column on universal test machine (UTM), external supporting point distance is 20.0 mm, internal supporting point distance is 10.0 mm. Specimen was loaded with 0.2 mm/min of cross head speed until fracture and at the time of broken of specimen, measuring loading value with PC software. Results: The results were obtained as follows: 1. Flexure strength of uncolored zirconia was higher than that of colored zirconia. 2. In uncolored zirconia, flexure strength of LAVATM Ceramic was more higher than the other ceramics, and it showed statistical difference between LAVATM Ceramic and Cercon Smart Ceramic (P<0.05). 3. In colored zirconia, flexure strength of LAVATM Ceramic was more higher than the other ceramics too, but they did not show statistical difference (p>0.05). 4. In Weibull analysis, Characterastic strength was showed highest value to uncolored LAVATM Ceramic and lowest value to Z-match ceramic, and Weibull modulus(m) of uncolored zirconia was higher than that of colored zirconia. 5. In XRD analysis, all group except Z-match showed high peak of t-ZrO2 but they did not show m-ZrO2. Colored zirconia group showed lower peak of t-ZrO2 than that of uncolored zirconia group.

• 대한치과보철학회지
• /
• 제37권5호
• /
• pp.597-606
• /
• 1999

This study was performed to evaluate the effect of aging and thermal cycling on the biaxial flexure strength of low commercially available veneering resin composites for crown(Dentacolor : DC, Artglass : AG, Esternia : ET and Targis : TG). Disc specimens were fabricated in a teflon mold giving 12mm in diameter and 1mm in thickness. All samples were divided into 4 groups. Group 1 was dried in a dessicator at $25^{\circ}C$ for 30 days. Group 2 was immersed in distilled water at $37^{\circ}C$ for 30 days. Group 3 was immersed in distilled water at $65^{\circ}C$ for 30 days. Group 4 was subjected to 10,000 thermal cycles between $5^{\circ}C\;and\;55^{\circ}C$, and the immersion time in each bath was 15 seconds per cycle. Biaxial flexure test was conducted using the ball-on-three-ball method at the cross head speed of 0.5mm/min and fracture surfaces were observed with scanning electoron microscope. The results obtained were summarized as follows; 1. Weibull modulus values, except for the AG group, decreased after thermal cycling treatment. 2. Biaxial flexure strength values of aging group at $37^{\circ}C$ were the lowest in all sample groups. Except for the DC group, strength values were significantly decreased for the drying group. 3. After thermal cycling test, the highest value of biaxial flexure strength of 188.8 MPa was observed in the ET group and the lowest value of 73.2 MPa was observed in the DC group. The strength values showed the significant differences in each group (p<0.05). 4. Observation of surfaces after thermal cycling test revealed the ditching in the part of surrounding large fillers.

• 대한치과보철학회지
• /
• 제41권1호
• /
• pp.71-80
• /
• 2003

Development of new ceramic and esthetic need of patient increased the use of ceramic restorations. The purpose of this study was to confirm the possibility of recycling for IPS Empress2 which has a lot of advantages in esthetics. 1st, 2nd and 3rd pressed disc-shaped($10{\times}1.5mm$) IPS Empress 2 specimens were made with IPS Empress ingot(shade 200, Ivoclar, Liechtenstein) and pressing furnace(IPS Empress EP 500, Ivoclar, Liechtenstein). Flexure strength was measured with universal testing machine(Zwick 145641, Zwick, Germany), and color change and staining resistance of specimens were evaluated with colorimeter (Model TC-6FX, Tokyo Denshoku Co., Japan). The followings were drawn from this study : 1. Flexure strength of the 1st, the 2nd, and the 3rd pressed specimens showed 236.78 MPa. 247.16MPa, and 220.72MPa, respectively. Flexure strength of the 2nd pressed specimens was higher than others, but there's no statistical difference between them. 2. The color difference between the 1st and the 2nd pressed specimens was 3.25, and that between the 1st and the 3rd pressed specimens was 3.63(P<0.05). 3. The color change after staining of the 1st, the 2nd. and the 3rd pressed specimens were 1.43, 2.64, and 1.45, respectively. In this study, reused IPS Empress 2 specimens showed insignificant change of flexure strength and stain resistance, but they showed some color change according to reuse. From this results, the limited possibility of reuse for IPS Empress 2 could be considered.

• Restorative Dentistry and Endodontics
• /
• 제31권1호
• /
• pp.58-65
• /
• 2006

이번 실험의 목적은 이축 굴곡 강도 시험의 복합레진에서의 적용가능성을 위해 기존의 3점 굴곡 강도 시험과 이축 굴곡 강도 시험을 이용하여 치과용 광중합형 레진의 강도를 측정하고, 이를 Weibull modulus를 이용하여 상대적 신뢰도를 비교하는 것이다. 이번 실험에 사용된 재료는 $MICRONEW^{TM},\;RENEW^{(R)}$ (Bisco, Schaumburg, USA)의 두 가지 광중합형 수복 재료이다. 이축 굴곡 강도 측정에는 International Organization for Standardization (ISO) 6872 규정에 따라 piston-on-3-ball test를 사용하였으며 검사 시편은 직경이 각각 12 mm (지지원의 반지름 3.75 mm), 16 mm (지지원의 반지름 5 mm), 두께가 각각 0.5 mm, 1 mm, 2 mm인 여섯 개의 군으로 나누어 제작하였으며 각 군당 시편을 20개씩 제작하였다. $MICRONEW^{TM}$와 $RENEW^{(R)}$의 실험 결과, 이축 굴곡 강도가 3점 굴곡 강도보다 높은 평균값을 나타내었고 이축 굴곡 강도의 모든 군이 3점 굴곡 강도보다 높은 Weibull modulus 값을 보여, 이축 굴곡 강도 시험이 상대적으로 실험적 오차의 영향을 적게 받는 방법으로 신뢰 할 수 있었다. 또한 이축 굴곡 강도 시험에서 시편의 두께가 2 mm일 때 가장 높은 Weibull modulus를 나타내었으며 이축 굴곡 강도시험군 중, $MICRONEW^{TM}$의 두께 2 mm군에서는 지지원의 반지름에 따른 굴곡 강도의 통계학적 유의차이가 없었고 (p>0.05), 이를 제외한 모든 군에서 시편의 두께와 지지원의 반지름에 따른 굴곡 강도의 통계학적 유의차이가 있었다 (p<0.05). 위의 결과로 미루어 볼 때 두께 2 mm군에서 이축 굴곡 강도는 기존의 3점 굴곡 강도 시험보다 우수한 것으로 추천할 수 있는 방법이다.

• Structural Engineering and Mechanics
• /
• 제12권1호
• /
• pp.71-84
• /
• 2001

The objective of this paper is to develop a simplified method that could predict the strength of concrete filled steel tube (CFT) columns applicable to high strength material under combined axial compression and flexure. The simplified method for determining the strength of CFT columns is based on the interaction curve of the section approached by a polygonal connection of the points. These points are determined by using symmetrical properties of the CFT section. For each point, a simple equation is proposed to determine the strength of the slender columns under compression and flexure. The simple equation was adjusted with results of elasto-plastic analysis results. Validation of the simplified method is undertaken by comparison with data from the test conducted at Kyushu University. These results confirm the fact that the simplified method could accurately and reliably predict the strength of CFT columns under combined axial compression and flexure.

• 구강회복응용과학지
• /
• 제17권3호
• /
• pp.199-204
• /
• 2001

This study was to investigate the reused possibility of zirconia reinforced glass-ceramic(IPS Empress Cosmo ceramic) with sprue button in the flexure strength and fracture toughness. 40 disk-shaped ceramic specimens (20 specimens: as-pressed material; 20 specimens: reused material) with approximately 1.7 mm thickness and 15 mm diameter were prepared by "lost wax" technique. The remnants(sprue buttons) were used for repressing. The surface treatments for the discs were gradually abraded with 320, 800, 1200, and 2000 grit SiC sandpaper. The specimens were evaluated their flexure strength with the biaxial flexure jig(ball-on-three balls) and their fracture toughness with Vickers Indentation-microfracture test. The Weibull moduli were calculated for biaxial flexural strength. The mean flexure strength and fracture toughness of each group were $122.2{\pm}18.3MPa$, $1.00{\pm}0.09MPa{\cdot}m^{0.5}$ (as-pressed ceramics), and $122.2{\pm}20.3MPa$, $1.01{\pm}0.10MPa{\cdot}m^{0.5}$ (reused ceramics). There were no significant differences in the strength and the fracture toughness between the as-pressed and the reused IPS Empress Cosmo ceramic (P>0.05). This implied zirconia reinforced glass-ceramic(IPS Empress Cosmo ceramic) could be used one more time by reusing of sprue button in the flexure strength and fracture toughness.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.137-142
• /
• 2001

In structural applications, brittle materials such as soda-lime glasses and ceramics are often subjected to multiaxial stress. Brittle materials with crack or damaged by foreign object impacts are abruptly fractured from cracks, because of their properities of very high strength and low fracture toughness. But in most cases, the residual strength has been derived from tests under uniaxial stress such as a 4-point bend test. The strengths under multiaxial stresses might be different from the strength. In comparable tests, the residual strength under biaxial stress state by the ball-on-ring test was greater than that under the uniaxial one by the 4-point bend test. In the case that crack having 90deg. to loading direction, the ratio of biaxial to uniaxial flexure strength was 1.12. At a different crack angle to loading direction when it was evaluated by the 4-point bend test, the residual strength was different and the ratio of 45deg. to 90deg. was 1.16.