• Steel and Composite Structures
• /
• 제20권3호
• /
• pp.487-500
• /
• 2016

In order to investigate the flexural bearing capacity of panel zone of diaphragm-through joint between concrete filled square steel tubular column and steel beam, four specimens were tested under static tension loads to study the mechanical properties and bearing capacity of diaphragm-through joints with a failure mode of panel zone. Finite element models of these specimens were developed to simulate the test and compare the predicted failure modes, load-displacement curves and bearing capacities with the experimentally observed. It was found that the tensile load from the steel beam flange is mainly shared by the square steel tube and the diaphragm. The diaphragm plastic zone appears along the cross-section lines enclosed by the square steel tube and the influence of steel beam web on the plastic zone of the steel tube is significant and cannot be neglected. Computational models of yield lines on square steel tube and diaphragm are established based on the distribution pattern of the plastic zone, and an analytical method for the evaluation of the bearing capacity of the joint is proposed. The theoretical results and the experimental data are compared and found in good agreement.

• 한국구조물진단유지관리공학회 논문집
• /
• 제10권6호
• /
• pp.183-190
• /
• 2006

본 연구는 철근콘크리트 보에 대해 선가력 후 보강재료별로 보강 효과를 파악하기 위하여 휨 실험한 결과, 다음과 같은 결론을 얻었다. 실험결과, CB 보강 실험체가 콘크리트 내부에 매입되어 일체 거동함으로써 휨내력 향상 및 연성능력 면에서 가장 우수한 것으로 나타났으며, 섬유계 보강재인 CFS와 GFS 보강 실험체 또한 우수한 내력을 가지는 것으로 나타났다. GSP 보강실험체의 경우 다른 보강 실험체에 비해 보강재 자체의 내력은 큰데 반해 콘크리트와 부착성이 떨어져 상대적으로 낮은 보강효과를 보였으며 실제 구조체에서는 콘크리트와 부착성이 개선 되어 보다 큰 보강효과를 발휘할 것으로 사료된다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제22권2호
• /
• pp.133-140
• /
• 2018

본 연구에서는 중공형의 PHC말뚝과 강관말뚝을 합성한 중공형 콘크리트 충전 강관(HCFT)말뚝의 거동분석을 위한 수치해석 모델을 개발하였고 휨강도시험에 적용하여 모델의 타당성을 검증하였다. 개발된 비선형 유한요소해석 모델의 적정성을 파악하기 위해 실물 시험 결과와 비교하였고 이를 활용하여 HCFT말뚝에 적합한 접촉조건, PC강봉의 제원에 따른 효과, 콘크리트 두께에 따른 효과 등을 분석하였다. 소성응력분배법을 적용하여 HCFT말뚝의 휨강도 산정식을 제안하였고 시험 및 해석결과와 비교하여 활용성을 검증하였다. 본 연구의 결과는 HCFT말뚝의 최적설계 및 거동분석에 기초자료로 활용될 수 있을 것으로 판단된다.

• Steel and Composite Structures
• /
• 제42권4호
• /
• pp.447-458
• /
• 2022

Cold-formed steel (CFS) sections are thin-walled, therefore, more susceptible to different types of geometric imperfections. Global type of geometric imperfections has a significant impact on the load-carrying capacity of flexural members. This paper reports an experimental study that discusses the influence of global imperfections on the flexural response of CFS built-up I-beams composed of two lipped channels, with simply supported ends, under four-point loading. Global imperfections of magnitude over eight times the maximum permissible ones were induced in the specimens, leading to their distress. Using various simple stiffening schemes, the capacity and stiffness of the distressed specimens were improvised. The performance comparisons were made based on the maximum loads resisted, flexural stiffnesses offered, and failure modes experienced by the specimens. As experimental data on such distressed specimens are currently lacking in the literature, the test results of the present study will provide the necessary data needed by future researchers to numerically extend this study further, which will help in the development of necessary design guidelines for the same. The stiffening schemes significantly improved the structural efficiency of distressed specimens in terms of strength and stiffness, by over 60%. As a result, an effective and time-saving solution to such realistic structural engineering problems is given.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 봄 학술논문 발표대회
• /
• pp.189-190
• /
• 2023

Environmental pollution problems are occurring in Jeju Island due to negative treatment of basalt waste. Measures for various approaches and utilization measures are needed to solve the problem of waste stones that occur during basalt processing. In this study, the Properties of permeable blocks with basalt were identified and the applicability and functionality as building materials were reviewed. This experiment is basic data for evaluating the functionality of the permeable block by manufacturing permeable blocks using basalt waste stones and analyzing flexural strength and compressive strength. The higher the basalt waste stone replacement rate, the lower the flexural strength and compressive strength, but it was judged that 20% of basalt waste stone replacement rate that satisfies the minimum flexural strength (4.0MPa) stipulated in KS F 4419 was appropriate. In addition, additional permeability coefficient and absorption rate experiments tended to increase as the basalt lung stone replacement rate increased. Therefore, it is judged that the permeable block using basalt waste stone is superior to the existing permeable block.

• 한국구조물진단유지관리공학회 논문집
• /
• 제20권1호
• /
• pp.64-71
• /
• 2016

본 논문에서는 UHPC 바닥판과 강재 거더를 이용하여 합성보를 구성할 때, UHPC 바닥판의 높은 강도와 강성으로 인하여 합성보 구성 시에 강재 거더의 상부 플랜지를 없앤 역T형 거더를 적용하고자 하였다. 그러나 현재까지 강재 복부에 설치되는 전단연결재에 대한 거동, 역T형 강거더 합성보의 휨거동 특성 등은 실험 및 이론적으로 평가된 적이 거의 없는 실정이다. 이를 위하여 UHPC 압축강도, 전단연결재 간격 및 바닥판 두께 등을 변수로 하는 역T형 거더와 UHPC바닥판 합성보 16개의 휨거동 실험결과를 근간으로 하여 실험결과와 UHPC의 인장연화 거동을 고려한 재료모델 해석결과를 비교하였다. 역해석에 의한 인장연화곡선에서 UHPC의 인장강도는 6.57 MPa(120MPa의 경우) 및 9.57 MPa(150MPa의 경우)를 나타내고 있으며, 전단연결재 간격이 좁을수록 실험결과와 해석결과가 명확하게 근접하는 겻으로 나타났으며, 바닥판 두께가 두꺼우며 UHPC 압축강도가 작을수록 동일한 경향이나, 이 영향은 다소 작은 것으로 나타났다. 따라서 실험결과와 해석결과를 종합적으로 비교하면, UHPC 합성보의 실험결과와 해석결과는 비교적 잘 일치하고 있으므로 재료 실험으로부터 산정된 인장연화곡선은 UHPC의 실제 거동을 합리적으로 반영한다고 판단된다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
• /
• pp.601-604
• /
• 1999

The objective of this study is to investigate the flexural behavior of reinforced concrete columns confined by lateral ties. This test was carried on the twelve reinforced concrete columns, 200$\times$200$\times$800mm size. objected to flexure and constant axial loads. The main variables are concrete strength, the configuration of lateral ties and the amount of lateral ties. Test results indicated that steel configuration plays an important role in column behavior, and a proper configuration of lateral ties can be more ductile than the reduce of the space of lateral ties. By this experiment, the ductility of high-strength concrete columns designed on A.C.I Code is not adequate, and are concluded that the design of high-strength concrete column is executed by more lateral ties under high axial loads.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 춘계학술발표대회 논문집
• /
• pp.167-170
• /
• 2000

The flexural vibration of a sandwich beam with partially inserted viscoelastic layer has been studied using the finite element analysis in combination with an experiment. Effects of length and thickness of partial viscoelastic layers on system loss factor(${\eta}_s$) and resonant frequency(${\omega}_r$) were considerably large. The thicker the viscoelastic layer in a sandwich beam, the larger the system loss factor in Mode 1 as compared with that in Mode 2. The loss factor increased almost linearly with increasing the length of partial viscoelastic layer. Effects of thickness of beams were also considered.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 춘계학술발표대회 논문집
• /
• pp.130-133
• /
• 2001

Recent days composite bridge deck is gaining attraction due to many advantages such as light weight, high strength, corrosion resistance, and high durability. In this study, composite sandwich deck models of hat, box, and triangular section type were fabricated by VARTM process. For those models, three point flexural test was carried out both in strong and weak axis. The experimental results are compared with each other to determine efficient section type. Also finite element analysis was performed to verify analysis model. It is demonstrated that the results of numerical analysis agree well with experimental results.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2002년도 학술.기술논문발표회
• /
• pp.77-86
• /
• 2002

In this study we intended to investigate properties of cement mortar with recycled PET fiber, PE fiber, and PP fiber such as slump flow, compressive strength, tensile strength, and flexural strength. As results of experiment, several properties of specimen with recycled PET fiber were little low comparing those of specimen with PE fiber and PP fiber. But if we see from point of economy and recycle of industrial wastes, it has enough reason to be used. Compressive strength of specimen with recycled PET fiber at 56 days was about 10% higher, but tensile strength and flexural strength were lower than that of no-fiber.