• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.11
• /
• pp.5200-5222
• /
• 2017

The separation of control plane and data plane in Software Defined Network (SDN) makes it flexible to control the network behavior, while also causes some inconveniences to the link failure recovery due to the delay between fail point and the controller. To avoid delay and packet loss, pre-defined backup paths are used to reroute the disrupted flows when failure occurs. However, it may introduce large overhead to build and maintain these backup paths and is hard to dynamically construct backup paths according to the network status so as to avoid congestion during rerouting process. In order to realize congestion aware fast link failure recovery, this paper proposes a novel method which installs multi backup paths for every link via source routing and per-hop-tags and spread flows into different paths at fail point to avoid congestion. We carry out experiments and simulations to evaluate the performance of the method and the results demonstrate that our method can achieve congestion aware fast link failure recovery in SDN with a very low overhead.

• Proceedings of the IEEK Conference
• /
• 2000.11a
• /
• pp.287-290
• /
• 2000

This paper analyze link-sharing mechanisms in packet networks based on the hierarchical class based queueing. The CBQ outlines a set of flexible, efficiently implemented gateway mechanisms that can meet a range of service and link-sharing requirements. We have analyzed the Class level(B, C, D) using the EWMA (Exponential Weighted Moving Average) weight value and EWMA average limit value.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.370-375
• /
• 1992

This paper deals with the scheduling and simulation for FMC(Flexible Manufacturing Cells). In order to achieve CIM, there is a critical need to link factory level and machine level. The primary functions performed by this link for all jobs issued to the shop floor and cell include short-term scheduling and dynamic operational scheduling. Here, hierarchical control structure is introduced to define these functions. And Intelligent scheduling through expert module is adopted for efficiency of FMC operation. Computer simulation reveals that expert scheduling method is better than heuristics in various performance index.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.04b
• /
• pp.175-180
• /
• 1993

The nonlinear integro-differential equations of motion of a two-link structurally flexible planar manipulator executing contact tasks are presented. The equations of motion are derived using the extended Hamilton's principle and the Galerkin criterion. Also, Models for the wrist-force sensor and impact that occurs when the manipulator's end point makes contact withthe environment are presented. The dynamic models presented can be used to studythe dynamics of the system and to design controllers.

• 제어로봇시스템학회:학술대회논문집
• /
• 1989.10a
• /
• pp.600-605
• /
• 1989

A theoretical study is presented for the end-point holding control of a one-link flexible arm, whose base is subjected to a lateral fluctuation. The arm is clamped on a rigid hub mounted directly on the shaft of d.c. servomoter. The tip position is measured by a gap sensor fixed in space isolated from the system vibration. The arm is controlled so as to make the end point stay precisely at its initial position even if the base is fluctuated.

• International Journal of Control, Automation, and Systems
• /
• v.4 no.4
• /
• pp.495-505
• /
• 2006

A class of robust control for flexible joint manipulators with nonlinearity mismatched uncertainty is designed based on Lyapunov approach. The uncertainties are unknown but their values are within certain prescribed sets. No statistic information of the uncertainties is imposed. The control which utilizes state transformation via virtual control is proposed. The resulting robust control guarantees practical stability for the transformed system and later the stability for the original system is proved. The designed robust control is implemented by experiments in a 2-link flexible joint manipulator.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.2
• /
• pp.385-392
• /
• 1993

This paper presents a new stable composite control law for the flexible joint robot manipulators, which incorporate an additional stabilizing control law with the sliding property. The singularly perturbated models in this paper include inertia moments which are functions or the deformations of actuators as well as link positions. The values of renewedly defined fast controller variables are computer from the corrected reduced-order model without additional computational loads. Proposed schemes are compared with the conventional one. The simulations for 2 DOF flexible joint manipulator show that the proposed schemes are more stable than the conventional scheme, and especially effective for the manipulator with high joint-flexibilities.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11a
• /
• pp.219-224
• /
• 2001

An accurate tip position control of a single-link flexible manipulator subjected to torque disturbance is achieved by utilizing so called sliding mode controller with disturbance estimation (SMCDE). After formulating the governing equation of motion in the state 1pace representation, a stable sliding surface is designed via the LQR method. The SMCDE is then synthesized by integrating equivalent sliding mode controller with the disturbance estimator which is featured by an integrated average value of the imposed disturbance over a certain sampling period. The regulating tip motion of the flexible manipulator is evaluated by employing the proposed SMCDE.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.04a
• /
• pp.185-189
• /
• 1992

This paper prsents an end-point control of a one-link flexible arm with a payload by using closed loop control. Tip position of arm is shifted by the base motion according to DC servomotor, whivh is driven by a feedback signal composed of the tip displacement and the estimated tip velocity. The shifting problem of the arm from initial position to desired position is considered by the variation of the displacement gain Gd and velocity agin Gv. Theoretical results are obtained by applying the method of the Laplace transform to the governing equations and the method of numerical inversion. This system is composed of a flexible arm with payload, DC servomotor, and a ballscrew mechanism. The flexible arm is mounted on a mobile stage driven by a servomotor and ballscrew. In controlling the tip displacement of flexible arm, the fundamental bode vibration is supressed more rapidly with an increase of the velocity feedback gain Gv and the feedback displacemenmt gain Gd. Theretical responses are approximately in good agreement with those obtained experimentally.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.04a
• /
• pp.369-373
• /
• 1992

Force control of a planar two-link structurally flexible robotic manipulator is considered in this study. The dynamic model is obtained by using the extended Hamilton's principle and the Galerkin criterion. A method is pressented toobtain the linearized equations of motion in Cartesian space for use in designing the control system. The approachto solving the control problem is to use feedforward and feedback control torques. The feedforward torques maneuver the flexible manipulatro along a nominal trajectory and the feedback torques minimize any deviations from the nominal trajectory. The linear quadratic Gaussian/loop transfer recovery (LQG/LTR) design methodology is explotied to design a robust feedback control system that can handle modeling errors and sensor noise, and operates on Cartesian space trajectory errors. The Lqg/LTR compenstaor together with a feedforward ollp is used to control the flexible manipulator. Simulated results are presented for a numerical example.