• 산업경영시스템학회지
• /
• 제23권61호
• /
• pp.13-22
• /
• 2000

To apply the queueing network theory in evaluating performances of flexible manufacturing systems, it is generally assumed that the processing times are distributed exponentially. However, in FMS, processing times are usually deterministic. In this study the performance measures of FMS are approximated under the assumption that processing times are usually deterministic. Multi-classes of parts and single server and multi-server stations are considered in the model. This study also that, in the numerical example, this approach yields better solutions than those obtained by the pure Linearizer algorithm, when the processing times are deterministic.

• 산업경영시스템학회지
• /
• 제24권67호
• /
• pp.19-26
• /
• 2001

A design issue for a flexible manufacturing system is to find the number of each resource type which assures a given production ratio with a minimal cost. The FMS is modeled as a closed queueing network with a local buffer of limited capacity. An efficient method to determine this optical configuration is presented. The proposed method consists of three steps : 1) determine a lower configuration, 2) derive a heuristic solution, 3) find the optimal solution. The derived heuristic solutions are close to the optical solution.

• 산업경영시스템학회지
• /
• 제18권33호
• /
• pp.79-86
• /
• 1995

This paper intends to develope the multi-objective loading model in a flexible manufacturing system (FMS) to support decision maker under fuzzy environment. To obtain the optimal solution, this paper uses interactive fuzzy multi-objective linear programing(IFMOLP) and describes the process of optimal solution. As a case study, numerical examples are demonstrated to show the effectiveness of the proposed model.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2008년도 International Meeting on Information Display
• /
• pp.1459-1462
• /
• 2008

In this paper we describe solutions to address critical challenges in direct fabrication of amorphous silicon thin film transistor (TFTs) arrays for active matrix flexible displays. For all flexible substrates a manufacturable handling protocol in automated display-scale equipment is required. For metal foil substrates the principal challenges are planarization and electrical isolation, and management of stress (CTE mismatch) during TFT fabrication. For plastic substrates the principal challenge is dimensional instability management.

• 산업경영시스템학회지
• /
• 제21권47호
• /
• pp.35-45
• /
• 1998

Scheduling problem in Flexible Manufacturing Systems(FMS) is complex because of various situation of Manufacturing Systems. Especially, in case of short-term scheduling demanding high efficiency, low cost at short-period, efficient scheduling is a serious problem. To solve this problem, many dispatching rules are developed. But, it leave much to be desired, because real situation in shop floor is complex and real-time scheduling is needed in real manufacturing shop floor. In this paper, search algorithm that allocate different dispatching rules to each machine is presented to complement lack of dispatching rule and develop practical real-time scheduling system. The search algorithm is described in detail. First, algorithm detect machine breakdown, evaluate each dispatching rule. dispatching rules for each machine meeting performance criteria are ranked. The algorithm selects new dispatching nile for bottleneck machine. The effectivenes and efficiency of the mixed dispatching rule and search algorithm is demonstrated.

• 한국공작기계학회논문집
• /
• 제10권3호
• /
• pp.83-89
• /
• 2001

In this paper, we discuss the vibration suppression control of spatial redundant flexible manipulators through pseudo-inversed of Jacobian. In order to verify our method, the experiments are performed for PTP(Point To Point) motion of spa-tial flexible manipulators(1) with no redundancy(2) with one redundant DOF(degree of freedom). Finally, a comparison between these results is presented to show the performance of out approach.

• 한국생산제조학회지
• /
• 제22권5호
• /
• pp.774-781
• /
• 2013

A structural analysis was carried out for a 60 N.m class flexible disk coupling. Flexible disk couplings are used to transmit power between two shafts. When a flexible coupling is used, some amount of misalignments such as angle of deviation and end play can be allowed in assembling the shafts. However, the maximum allowable misalignment should be decided to guarantee the fatigue life. In this study, the effect of the angle of deviation and end play on the maximum stress was investigated. From the analysis results, it was shown that the angle of deviation has a greater effect on the maximum stress than the end play. Furthermore, the dimensions of the disk plate were optimized to realize a better design. From the optimization, the maximum stress could be reduced by up to 5.2%.

• 한국기계가공학회지
• /
• 제12권6호
• /
• pp.30-36
• /
• 2013

An FFD(flexible fine die) is an embossed mold that consists of a thin plate ranging from 0.6 to 3 mm in thickness. FFDs are primarily used for cutting LCD films and F-PCB sheets. In the high-speed micro-milling process of flexible fine dies, the lubrication and cooling of the cutting edges is very important from the aspect of eco machining and cutting performance. In this paper, a comparative study of tool wear and surface roughness between cutting fluid and hybrid lubrication for eco-machining of FFD was conducted for processes of high-speed machining of highly hardened material (STC5, HRC52). Especially, the incorporated fluid method for eco machining, in which the cutting performances can be simultaneously measured, was introduced. The machining results show that hybrid lubrication, instead of conventional cutting fluid, leads to excellent tool wear and surface roughness and represents the proper conditions for eco micro-machining of flexible fine dies.

• 한국생산제조학회지
• /
• 제20권3호
• /
• pp.245-250
• /
• 2011

An UV/thermal hybrid nanoimprint lithography system was designed and implemented for the pattern transfer to flexible substrates. This system can utilize a plate stamp, roll stamp, and film stamp. For all cases of using those stamps, this system is also switchable an UV or thermal nanoimprint lithography mode. This paper shows how to design the heating and UV curing plates and proposes how to change them easily. Because the pressure condition and the speed of the press roller varies by the characteristics of the stamp and substrate, all the parameters related to the nanoimprint lithography have to adjustable. Some transferred patterns are shown in this paper to verify the performance of the hybrid nanoimprint lithography system. The flexible substrates with nano-scale patterns on them will be key components for next generation technologies such as flexible displays, bendable semi-conductors, and solar cells.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.I
• /
• pp.811-813
• /
• 2005

Purpose-built ink jet printheads are being recognized as useful tools in manufacturing where precision deposition is required. Ink jet technology is a non-contact, non-contaminating digital process compatible with clean rooms. New manufacturing applications are driving printhead designs to smaller drops, increased productivity. This paper describes Dimatix's new tools designed to facilitate development of manufacturing processes for both rigid and flexible substrates and development of new electronic fluids.