• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.1526-1531
• /
• 2008

The objective of this study is to evaluate the loading capacity of lattice girder according to loading position. 3-point flexible strength tests were performed on three types of lattice girder, such as LG-$50{\times}20{\times}30$, LG-$70{\times}20{\times}30$, and LG-$95{\times}22{\times}32$, mainly used in Korea. Two types of loading position for each flexible strength test were used to analyze the behavior of load-deformation. In 3-point flexible strength test, the difference of the average of maximum flexible strength according to loading position had the range from 10% to 33%.

• 한국터널지하공간학회 논문집
• /
• 제10권4호
• /
• pp.371-382
• /
• 2008

본 연구의 목적은 국내터널현장에서 강지보재로 주로 사용되어지고 격자지보재(Lattice Gilder)의 공학적인 성능을 보다 객관적으로 판단하기 위한 실내성능평가기법의 제안에 있다. 본 연구를 위하여 국내에서 격자지보재로 주로 사용되는 $LG-50{\times}20{\times}30$, $LG-70{\times}20{\times}30$, 및 $LG-95{\times}22{\times}32$를 사용하여 3-point 휨강도 실험 및 4-point 휨강도 실험을 수행하였다. 또한, 하중재하위치에 따른 격자지보재의 하중-변위거동을 분석하기 위하여 각각의 실험방법에서 두 가지 하중재하방식을 사용하여 실험을 수행하였다. 각 부재에 스트레인 게이지를 부착하여 각각의 실험방법에 따라 각 부재에 작용하는 하중분포를 분석하였다. 3-point 휨강도 실험에 적용한 두 가지 하중재하방식으로 측정된 평균 최대하중은 $10%{\sim}33%$까지 차이가 나타났으며, 4-point 휨강도 실험에 적용한 두 가지 하중재하방식에 의해 측정된 평균 최대하중은 거의 차이가 없었다. 4-point 휨강도 실험의 평균 최대하중은 3-point 휨강도 실험보다 $13.56%{\sim}31.55%$와 정도 크게 나타났다. 3-point 휨강도 실험은 주강봉에 주로 하중이 집중되는 반면 4-point 휨강도 실험은 각 부재로 비교적 골고루 하중이 작용하는 것으로 나타났다.

• 상하수도학회지
• /
• 제26권1호
• /
• pp.13-20
• /
• 2012

In this paper, we present the result of an investigation pertaining to the pipe stiffness of buried flexible pipes. Pipe stiffness (PS) formula for the parallel plate loading condition is derived based on the elasticity theory. Vertical and horizontal displacements are also derived. Vertical deflection is always larger than the horizontal deflection because some of energy due to overburden load is stored in the pipe but the difference is negligibly small. In the study, mechanical properties of the flexible pipes produced in the domestic manufacturer are tested and the results are reported in this paper. In addition, pipe stiffness is determined by the parallel plate loading tests and the finite element analysis. The difference between test and analysis is less than 14% although there are significant variations in the mechanical properties of the pipe material. Therefore, it was found that the finite element analysis can be used to predict the pipe stiffness instead of conducting parallel plate loading test.

• 한국재난정보학회 논문집
• /
• 제13권4호
• /
• pp.491-498
• /
• 2017

본 연구의 주 목적은 연성 도로포장의 소성변형 예측모델을 개발하는 것이다. 목적을 수행하기 위하여 다양한 실험실 시험이 수행되었다. 소성변형 량을 측정하기 위하여 측면 구속압을 제공하는 새로운 반복 일축압축시험이 채택되었으며 소성변형 예측모델은 층별-변형률 이론이 적용되었다. 예측모델의 소성계수는 아스팔트 콘크리트 재료의 소성변형시험을 통하여 결정되었다. 본 연구가 수행된 범위내에서 반복 일축압축시험을 통한 연성포장의 소성변형 예측모델이 제안되었다. 제안된 소성변형 예측모델은 연성포장 층 재료의 거동을 적절하게 모사하는 것으로 나타났다.

• 산업경영시스템학회지
• /
• 제22권50호
• /
• pp.127-137
• /
• 1999

This study is concerned with the loading problems in flexible manufacturing system(FMS). The loading problem in FMS is a complex one, when the number of machine and job is increased. It may be time-consuming and even impossible to achieve an optimal solution about this problem mathematically. Thus, a heuristic method is recommended in order to gain near-optimal solutions in a practically acceptable time. A new loading algorithm is developed with a multi-criterion objective of considering the workload unbalance, and maximizing the machine utilization, throughput for critical resources such as the number of tool slots and the number of working hours in a scheduling period and so on. The results of SAS analysis indicated that true average throughput of proposed heuristic loading statistically exceeds that of Shanker and Srinivasulus loading algorithm at the significance level of 0.1.

• 대한기계학회논문집B
• /
• 제31권2호
• /
• pp.151-158
• /
• 2007

The mechanism of power transmission from motor torque to stem thrust and the operation characteristic of each stroke position are analyzed using the diagnostic signal, and effects of differential pressure on the performance of motor operated flexible wedge gate valve are investigated. Test facility consists of 76 mm motor operated valve(flexible wedge type), pump and pipe system. Static and dynamic test are performed separately, and two differential pressure conditions are applied in the dynamic test. To evaluate the performance of valve, test signals for the torque, thrust, current, voltage and stroke length are acquired by using UDS which is diagnosis device for motor operated valve, and each diagnostic signal is analyzed and compared. The characteristic of valve performance factors such as stem factor, rate of loading, valve factor, are evaluated, and these factors are found to be severely influenced by the fluid differential pressure.

• Structural Engineering and Mechanics
• /
• 제6권7호
• /
• pp.817-826
• /
• 1998

A finite element model based on the incremental endochronic theory for flexible pavement materials was developed in this study. Three grid systems with eight-node cubic isoparametric elements, and different loading steps were used to perform the calculations for a specimen of circular cylinder. The uniaxial stress experimental results on an asphalt mixture at $60^{\circ}C$ in SHRP conducted by University of California at Berkeley were used to check the ability of the derived numerical model. Then, the numerical results showed isotropic response and deviatoric response on the specimen in a three dimensional manner, which provided a better understanding for a deformed flexible material under the specified loading conditions.

• 대한산업공학회지
• /
• 제21권1호
• /
• pp.119-135
• /
• 1995

We consider problems of tool loading and scheduling in a flexible manufacturing system (FMS) in which tool transportation constitutes the major portion of material flows. In this type of FMSs, parts are initially assigned to machines and released to the machines according to input sequencing rules. Operations for the parts released to the machines are performed by tools initially loaded onto the machines or provided by an automatic tool transport robot when needed. For an efficient operation of such systems, therefore, we may have to consider loading and scheduling problems for tools in addition to those for parts. In this paper, we consider three problems, part loading, tool loading, and tool scheduling problems with the overall objective of minimizing the makespan. The part loading problem is solved by a method similar to that for the bin packing problem and then a heuristic based on the frequency of tool usage is applied for tool loading. Also suggested are part input sequencing and tool scheduling rules. To show the effectiveness of the overall algorithm suggested here, we compare it with an existing algorithm through a series of computational tests on randomly generated test problems.

• 대한산업공학회지
• /
• 제19권4호
• /
• pp.41-48
• /
• 1993

Prime advantage of flexible manufacturing systems(FMS) is a flexibility. Flexibility is expected to prolong the service life of a manufacturing facility and enable it to respond quickly and economically to dynamic market change. The FMS loading decision is concerned with the allocation of operations and tools to machines subject to technological and capacity constraints of the system. Modern FMS loading problem has the multiple objectives such as processing cost, time and work load balance. We propose multi-objectives which could be used to formulate the loading/routeing problem and sequencing decision which should be adopted for each part type in order to maximize the machine flexibility by Hamming distance matrix based on Incidance matrix. Finally, a numerical example is provided to illustrate the proposed model.

• 대한산업공학회지
• /
• 제15권1호
• /
• pp.65-75
• /
• 1989

This study complements the previous studies on workload distribution problems in Flexible Manufacturing Systems. Specifically, we consider the problem in two perspectives, the long-range policy and the short and medium-term planning and control. The long-term loading policy focusses on identifying the optimal loading of the system characterized by either balanced loading or unique unbalanced loading for which a steepest ascent method is developed. These results are then applied to study the optimal medium and short-term planning and control problems, for which a truncated dynamic programming method is developed in order to obtain the optimal allocation of the given operation mix of part types to work stations.