• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.12
• /
• pp.2205-2215
• /
• 1992

The stability of the flexible rotor mounted on circumferentially grooved floating ring journal bearings was investigated theoretically and experimentally. The floating ring journal bearing was analyzed by using JFO reformation boundary condition. The flexible shaft was analyzed by the finite element method based on Rayleigh beam theory. It was found that the measured ring speed agrees well with the theoretical results. The instability of the system due to not only the outer film but also the inner film of the bearing could be predicted by the theory which allows negative vapor pressure. The tendency that reducing the supply pressure of lubricant stabilizes the system was observed both experimentally and theoretically.

• Journal of KSNVE
• /
• v.5 no.2
• /
• pp.235-246
• /
• 1995

Experiment on the modal balancing of a flexible rotor supported on two kinds of fluid film bearings is performed to verify the modal balancing theory. The fluid film bearings are a tilting pad bearing and a two axial grooved journal bearing. One is inherently stable, but the other is not. The experimental result shows that the modal balancing method is effective for balancing of a high speed flexible rotor system. Besides, the critical speeds and mode shapes measured experimentally are in good coincidence with the results of rotordynamic analysis. Oil whip, which is the instability phenomenon due to fluid film force, is also observed during the experiment.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.1
• /
• pp.175-181
• /
• 2012

This paper presents a novel dynamic vibration absorber (DVA) to suppress the unbalance response of flexible rotor-bearing systems. The DVA unit consists of two DVAs, an adapter to place the DVAs and an adapter frame to locate the adapter. The essential feature of the proposed DVA unit is to place itself on any desirable location of the shaft without disassembling the rotor-bearing system under consideration. A simulation with a 3D element based commercial rotor dynamic software is made to test the possibility of the proposed DVA on the suppression of unbalance response in rotor-bearing systems. Experiments are performed to validate the proposed DVA unit. The simulation and experiments show that the proposed DVA unit is very effective to suppress the unbalance response in rotor-bearing system at designated rotational speeds of interest.

• Tribology and Lubricants
• /
• v.16 no.1
• /
• pp.39-45
• /
• 2000

In this paper, the effects of shaft and bearing flexibilities are investigated for the accurate modeling of a shaft-bearing system supported by ball bearings. Generally, rolling bearings are modeled by simple rigid pin-joint in the mechanical design. However, they can no longer be modeled by ideal boundary conditions in the advanced applications because the rigid pin-joint model cannot satisfy the current trends of mechanical design decreasing mass and reducing volume. Consequently the flexible support model of ball bearing is investigated using the static analysis module developed by A .B. Jones and T. A. Harris. A simple two-bearing system, supported by two deep groove ball bearings and radially loaded on the shaft midway between the bearings, is utilized to validate the coupled model of shaft-bearing system. Numerical computations using the model indicate that the shaft span length, locating/floating bearing arrangements and applied bearing size are significant factors in determining the mechanical behaviors. The flexible support model of ball bearing can be escaped to over-estimate in the bearing fatigue life. The proposed simple design formulation obtained by numerical simulations can approximately predict a rate of bearing life reduction as a function of shaft span length/shaft diameter (L/d).

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2004.11a
• /
• pp.175-185
• /
• 2004

Rotating disks are used in various machines such as data storage device, gyroscope, circular saw, etc. Transverse vibration of a rotating disk is very important for the performance of these machines. This work proposes a method to suppress transverse vibration of a very flexible rotating disk in non-contacting manner. A system considered in this study is a very flexible rotating disk with a thrust bearing pad which is located underneath the rotating disk. The pressure force generated in the gap between the rotating disk and the thrust pad pushes the rotating disk in the direction of axis of rotation while the centrifugal force and the elastic recovery force push the rotating disk in reverse direction. The balance between these forces suppresses the transverse vibration of the rotating disk. A coupled disk-fluid system is analyzed numerically. The finite element method is used to compute the pressure distribution between the thrust pad and the rotating disk while the finite difference method is used to compute the transverse vibration of a rotating disk. Results show that the transverse vibration of the rotating disk can be suppressed effectively for certain combination of air bearing and operating parameters.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.11a
• /
• pp.129-137
• /
• 2001

As the rotational speed and the track density are increased, the vibration of disk/spindle system becomes critical issue. In this work, we propose a simple inclined air bearing(20mm${\times}$20mm) system which is positioned very near to the rotating disk especially compact disc(CD) as a flexible disk, and we investigate suppressing effect about disk mode (0,0) both experimentally and numerically. We find dynamic stiffness and damping coefficients of bearing and apply to the disk vibration. The results show about 10 percent errors comparing to the experimental results. Also we investigate experimentally the reduction of disk vibration and power consumption with two different kinds of inclined bearing for normal disk drive system, which has tray and cover. We find inclined air bearing can decrease about 30 percents of the original disk vibration amplitude.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.6
• /
• pp.167-174
• /
• 2013

High speed rotor systems with magnetic bearings have been the subject of much research in recent years due to the potential for active vibration control. In this thesis, optimal design was conducted for an 8-pole heteropolar magnetic bearing used in the flexible rotor of a turbo blower. In connection with bearing stiffness, this optimal design process was conducted using a genetic algorithm(GA), which is based on natural selection and genetics. The maximum stiffness of the magnetic bearing-rotor was found by considering the critical speeds of the flexible rotor. As a result, the magnetic bearings were optimized to have maximum stiffness.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.5
• /
• pp.2001-2008
• /
• 2015

This paper proposes the concept of FlexPCB(flexible Printed Circuit Board) conductive structure for electrodynamic bearings. It has three main advantages: easy “printing” of considerably thin conductive wires, resulting in potential reduction in stray eddy currents; realization of specific conductive configurations with high precision to optimize the eddy current flowing; simplicity in being wound to cylinders or hollow cylinders of different diameters. To verify this new concept, the FlexPCB conductive structure was manufactured, an axial electrodynamic bearing test rig was built and the conductive structure's induced voltage was measured along the axial displacements from 0mm to 56mm at three rotating speeds. The finite element method was used to calcuatlate the flux density of electrodynamic bearing and induced voltage of the FlexPCB conductive structure. The experimental results are compared with the results from the FEM calculation. It is concluded that the measured and calculated induced voltages have consistency in the middle part of the bearing.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.387-392
• /
• 2007

Turbomachinery such as turbines, pumps and compressors, which are installed in transportation systems such as warships, submarines and space vehicles, etc., often perform crucial missions and are exposed to potential dangerous impact environments such as base-transferred shock forces. To protect turbomachinery from excessive shock forces, it may be needed to accurately analyze transient responses of rotors, considering the dynamics of mount designs to be applied with. In this study a generalized FE transient response analysis model, introducing relative displacements, is firstly proposed to accurately predict transient responses of a flexible rotor-bearing system with mount systems to base-transferred shock forces. In the transient analyses the state-space Newmark method of a direct time integration scheme is utilized, which is based on the average velocity concept. Results show that for the identical mount systems considered, the proposed FE-based detailed flexible rotor model yields more reduced transient vibration responses to the same shocks than a conventional simple model or a Jeffcott rotor. Hence, in order to design a rotor-bearing system with a more compact light-weighted mount system, preparing against any potential excessive shock, the proposed FE transient response analysis model herein is recommended.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.12
• /
• pp.1208-1216
• /
• 2007

Turbomachinery such as turbines, pumps and compressors, which are installed in transportation systems, including aircrafts, ships, and space vehicles, etc., often perform crucial missions and are exposed to potential dangerous impact environments such as base-transferred shock forces. To protect turbomachinery from excessive shock forces, it may be needed to accurately analyze transient responses of their rotors, considering the dynamics of mount designs to be applied. In this study a generalized FE transient response analysis model, introducing relative displacements, is proposed to accurately predict transient responses of a flexible rotor-bearing system with mount systems to base-transferred shock forces. In the transient analyses the state-space Newmark method of a direct time integration scheme is utilized, which is based on the average velocity concept. Results show that for the identical mount systems considered, the proposed FE-based detailed flexible rotor model yields more reduced transient vibration responses to the same shocks than a conventional simple model, obtained by treating a rotor as concentrated lumped mass, equivalent spring and a damper or Jeffcott rotor model. Hence, in order to design a rotor-bearing system with a more compact light-weighted mount system, preparing against any potential excessive shock, the proposed FE transient response analysis model herein is recommended.