• 제목/요약/키워드: Flat sheet membrane

검색결과 61건 처리시간 0.02초

분리막 종류에 따른 하수의 생물학적 고도처리 효율 비교 연구 (Comparison of Biological Nutrient Removal Efficiencies on the Different Types of Membrane)

  • 박종부;신경숙;허형우;강호
    • 한국물환경학회지
    • /
    • 제27권3호
    • /
    • pp.322-328
    • /
    • 2011
  • This study was performed to investigate the characteristics of nutrient removal of municipal wastewater in the membrane bioreactor system with the different types of membrane. Membrane bioreactor consists of three reactors such as two intermittent anaerobic and the submerged membrane aerobic reactor with flat sheet and hollow fiber membrane, respectively. The removal efficiencies of $COD_{cr}$, BOD, SS, TN and TP on the flat sheet membrane bioreactor were 94.3%, 99.0%, 99.9%, 70.3% and 63.1%, respectively. In addition, The removal efficiencies of $COD_{cr}$, BOD, SS, TN and TP on the hollow fiber membrane bioreactor were 94.0%, 99.3%, 99.9%, 69.9% and 66.9%, respectively. The estimated true biomass yield, specific denitrification rate (SDNR), specific nitrification rate (SNR) and phosphorus removal content on the flat sheet membrane bioreactor were $0.33kgVSS/kgBOD{\cdot}d$, $0.043mgNO_3-N/mgVSS{\cdot}d$, $0.031mgNH_4-N/mgVSS{\cdot}d$, and 0.144 kgP/d, respectively. In addition, the estimated true biomass yield, specific denitrification rate (SDNR), specific nitrification rate (SNR) and phosphorus removal content on the hollow fiber membrane bioreactor were $0.30kgVSS/kgBOD{\cdot}d$, $0.067mgNO_3-N/mgVSS{\cdot}d$, $0.028mgNH_4-N/mgVSS{\cdot}d$, and 0.121 kgP/d, respectively. There was little difference between the flat sheet and hollow fiber on the nutrient removal efficiencies except SNR and SDNR. These differences between them were caused by the air demand to prevent the membrane fouling. The flux and oxygen demand for air scouring were $19.0L/m^2/hr$ and $2.28m^3/min$ for the flat sheet membrane, and $20.7L/m^2/hr$ and $1.77m^3/min$ for the hollow fiber membrane on an average.

실규모 flat sheet MBR 운영 효율과 Fouling 특성을 위한 미생물 군집 평가 (Performance and microbial community analysis for fouling characteristics in a full-scale flat sheet membrane bioreactor)

  • 김승원;최정동
    • 상하수도학회지
    • /
    • 제37권6호
    • /
    • pp.325-334
    • /
    • 2023
  • Membrane bioreactor (MBR) provides the benefits on high effluent quality and construction cost without the secondary clarification. Despite of these advantages, fouling, which clogs the pore in membrane modules, affects the membrane life span and effluent quality. Studies on the laboratory scale MBR were focused on the control of particulate fouling, organic fouling and inorganic fouling. However, less studies were focused on the control of biofouling and microbial aspect of membrane. In the full scale operation, most MBR produces high effluent quality to meet the national permit of discharge regulation. In this study, the performance and microbial community analysis were investigated in two MBRs. As the results, the performance of organic removal, nitrogen removal, and phosphorus removal was similar both MBRs. Microbial community analysis, however, showed that Azonexus sp. and Propionivibrio sp. contributed to indirect fouling to cause the chemical cleaning in the DX MBR.

Silicone Rubber Membrane Bioreactors for Bacterial Cellulose Production

  • Onodera, Masayuki;Harashima, Ikuro;Toda, Kiyoshi;Asakura, Tomoko
    • Biotechnology and Bioprocess Engineering:BBE
    • /
    • 제7권5호
    • /
    • pp.289-294
    • /
    • 2002
  • Cellulose production by Acetobacter pasteurianus was investigated in static culture using four bioreactors with silicone rubber membrane submerged in the medium. The shape of the membrane was flat sheet, flat sack, tube and cylindrical balloon. Production rate of cellulose as well as its yield on consumed glucose by the bacteria grown on the flat type membranes was approximately ten-fold greater than those on the non-flat ones in spite of the same membrane thickness. The membrane reactor using flat sacks of silicone rubber membrane as support of bacterial pellicle can supply greater ratio of surface to volume than a conventional liquid surface culture and is promising for industrial production of bacterial cellulose in large scale.

평막을 이용한 침지형 막여과시스템에서 고농도 분말활성탄 주입에 의한 수처리성능 개선 효과 (The Effects of PAC (Powdered Activated Carbon) on Water Treatment Performance of an Immersed Membrane System Using Flat-sheet Membrane Module)

  • 가이샹쥐안;김한승
    • 상하수도학회지
    • /
    • 제21권2호
    • /
    • pp.195-201
    • /
    • 2007
  • A submerged flat-sheet membrane separation system integrated with PAC (powdered activated carbon) was used in this research in order to investigate the effects of PAC on the efficiencies of operation and treatment and to evaluate the performance of the system. The experiments were carried out under operating conditions of a filtration rate of 0.38 m/d, water temperature of $20-28^{\circ}C$, and PAC dose of 0 g/L (Run-A) and 20 g/L (Run-B). The influent concentrations of TOC (total organic carbon), $NH_4{^+}-N$ (ammonia nitrogen) and $UV_{254}$ (UV absorbance at 254 nm) were 2.48 mg/L, 1.4 mg/L and 2.53 1/m, respectively. TOC removal of 43.2 and 73.6%, ammonia nitrogen removal of 4.9 and 15.9%, and $UV_{254}$ removal of 20.6 and 31.6% were obtained for Run-A and Run-B, respectively. During an experimental period of 33 days, no change was found in TMP (Run-B), but the TMP in Run-A increased by 5 kPa after 29 days. This research showed that the filtrate quality and the performance efficiency were enhanced when PAC was introduced into the filtration system.

Performance prediction of flat sheet commercial nanofiltration membrane using Donnan-Steric Pore Model

  • Qadir, Danial;Nasir, Rizwan;Mukhtar, Hilmi;Uddin, Fahim
    • Membrane and Water Treatment
    • /
    • 제12권2호
    • /
    • pp.59-64
    • /
    • 2021
  • The rejection of sodium chloride (NaCl) and calcium chloride (CaCl2) single salt solutions were carried out for commercial nanofiltration NFDK membrane. Results showed that the NFDK membrane had a negative surface charge and had a higher observed rejection of 93.65% for calcium (Ca2+) ion and 78.27% for sodium (Na+) ions. Prediction of rejection for aqueous solutions of both salts was made using Donnan Steric Pore Model based on Extended Nernst-Planck Equation in addition to concentration polarization film theory. A MATLAB program was developed to execute the model calculations. Absolute Average Relative Error (% AARE) was found below 5% for real rejection of the NFDK membrane. This research could be used successfully to assess the membrane characterization parameter using a proposed procedure which can reduce the number of experiments.

$ENVIS^{(R)}$ MEMBRANE SYSTEM (평판형 정밀여과막)의 침지식 수처리 공정 적용에 관한 연구 (Application of $ENVIS^{(R)}$ MEMBRANE SYSTEM (Sumerged flat Sheet MF Membrane))

  • 이영무;장재영
    • 멤브레인
    • /
    • 제15권3호
    • /
    • pp.241-246
    • /
    • 2005
  • 본 연구는 하수 및 오폐수 처리를 위해 침지식 수처리 공정 적용을 위한 평판형 MF막인 $ENVIS^{(R)}$을 이용한 MBR SYSTEM 적용에 관한 연구이다. (주)퓨어엔비텍에서 만든 장치를 이용하여 공장의 오수시설($10\;m^3$/일)과 폐수처리장($30\;m^3$/일) 현장에서 실험을 수행한 결과, 공장 오수처리에 있어 제거율은 각각 SS $99.7\%$, BOD $97.6\%$, COD $96.8\%$였으며, 폐수처리에 있어 제거율은 각각 SS $99.6\%$, BOD $95.6\%$, COD $80.3\%$였다.

Hydroxy Polyimide 막의 제조와 이산화탄소 투과 특성 (Prepration of Hydoxy Polyimde Membranes and Their Carbon Dioxide Permeation Property)

  • 우승문;최종진;남상용
    • 멤브레인
    • /
    • 제22권2호
    • /
    • pp.128-134
    • /
    • 2012
  • 본 연구에서는 hydroxy polyimide (HPI)로 용매 증발법에 의해 제조가 되었다. 비다공성막의 기체투과성능측정 결과로써, $CO_2$ 투과도는 약 85 Barrer이고, $CO_2/N_2$선택도는 23으로 측정되었다. 고분자, 용매, 비용매-첨가제의 3성분계 시스템을 도입하여 평막과 중공사막을 제조하였고, 모폴로지와 기체투과성능을 전계방출형전자주사현미경과 버블플로우메타로 측정하였다. 평막과 중공사막에서 $CO_2$투과도와 $CO_2/N_2$ 선택도는 각각 18.28 GPU, 70 GPU를 6.72, 8.63으로 나타남을 확인하였다. 중공사막이 평막보다 기체투과특성이 우수하다는 것을 확인하였다.

응고조와 도프조성에 따른 폴리술폰 평막의 모폴로지 및 수투과도 평가 (Evaluation of Morphology and Water Flux for Polysulfone Flat Sheet Membrane with Conditions of Coagulation Bath and Dope Solution)

  • 우승문;정연석;남상용
    • 멤브레인
    • /
    • 제22권4호
    • /
    • pp.258-264
    • /
    • 2012
  • 본 연구에서는 응고조와 도프조성에 따른 투과특성을 알아보기 위해 첨가제로 PEG, PVP를 사용하였고, 상전이법을 이용하여 PSf 평막을 제조하였다. 고분자의 농도, 첨가제의 농도 그리고 응고조의 조성을 달리하여 제막하였다. 평막의 모폴로지와 수투과도를 각각 FE-SEM과 수투과 테스트 장치를 이용하여 측정하였다. 가장 높은 수투과도(986 L/mh)는 PSf 15 wt%, PEG 25 wt% 그리고 응고조로 물이 사용되었을 경우 나타났다. PSf/PEG조성일때 응고조에 DMAc의 함량이 증가할수록 순수투과도는 급격히 감소하였다. 그러한 결과 첨가제의 함량과 응고조의 조성의 변화가 모폴로지와 수투과 특성에 영향을 미치는 것을 확인하였다.

롤투롤 공정을 활용한 평판형 분리막의 대면적 제조 연구 (Scale-up Fabrication of Flat Sheet Membrane by Using a Roll-to-Roll Process)

  • 백동혁;유영민;김인철;박유인;남승은;조영훈
    • 멤브레인
    • /
    • 제34권1호
    • /
    • pp.79-86
    • /
    • 2024
  • 고분자 분리막의 대표적인 형태 중 하나인 평판형 분리막은 제조가 용이하여 실험실에서 분리막 소재 연구에서부터 실제 상용 분리막 생산에 이르기까지 널리 활용되는 분리막의 형태이다. 정밀여과 및 한외여과 등에 사용되는 평판형의 다공성 고분자 분리막은 주로 상분리 공정을 통해 제조할 수 있으며, 여기에는 비용매 유도 및 증기 유도 상분리 공정이 활용된다. 그러나 상분리 공정 특성상 주변 환경과 실험자에 따라 샘플 간 편차가 쉽게 발생하여 재현성의 확보가 어려운 점이 있다. 따라서 개발된 제조기술을 스케일업 및 재현성 확보를 위해 제어된 환경에서 연속식 대면적 제조가 가능한 롤투롤 제조장치가 필요하며, 본 연구에서는 실험실 스케일의 제조기술을 나이프 및 슬롯다이 롤투롤 공정으로 스케일 업 했을 때 나타나는 제조 환경 차이에 따른 분리막의 특성 변화를 비교하였다. 최종적으로 연속식 제조공정 인자에 대한 최적화를 통해 대면적 제조 시 분리막의 균일성을 확보하였다.