• Journal of radiological science and technology
• /
• 제30권2호
• /
• pp.153-159
• /
• 2007

Digital medical image commenced with an introduction of PACS has become more popular today in the radiation diagnosis and radiation treatment and made great progress, in particular, for medical testing field, whereas it has made slow progress for radiation treatment field. In order to accommodate the current trend of digital from analog, a spherical mechanical check device(SMCD) that is the form of spherical differing from the existing form of flat or cube has been designed and tested its practicability to replace the part in mechanical check with digital image from QA operation. If the distance maintains constance between source(target) and image detector with constant distance to the center of spherical mechanical check device(SMCD), the size will be shown as a constant image at all times regardless of its direction exposed. For the test, two accurate hemispheres are made and put together which results in a sphere of the equilateral circle. It enables a variety of implementation of the existing mechanical check using digital image as follows: congruity level of radiation field and light field, size accuracy of radiation field and collimation field, gantry rotation isocenter check, collimation rotation isocenter check, room laser accuracy check, collimation rotation angle check, couch rotation angle check, and more. In addition, it has proved its practicability in checking isocenter congruity level as real time at the time of simultaneous rotation between gantry and couch that is applied to the non-coplanar field, which had been hard to apply as a device formed of existing flat or cube.

• Journal of Bio-Environment Control
• /
• 제20권1호
• /
• pp.45-49
• /
• 2011

This research was carried out to investigate frost damage of mulberry tree (Morus alba) according to topographic characteristics in Buan province. The first bud-break, leafing, blooming and harvest date of mulberry tree in 2010 were two, four, fourteen and eight days later than those in 2009, respectively. These results were that daily mean temperature during March and April in 2010 were lower than those in 2009 by $2.3^{\circ}C$ and $2.4^{\circ}C$. Frost damage of orchards at flat-bottomed valley, flat near hill and lake, and plain were 50.0%,12.0%, and 4.2%, respectively. Also, frost damage of branch of below 15 mm in diameter was serious than that of branch over 16 mm, but orchard at flat-bottomed valley was high as the range of 46.2~54.0%. These results in 2010 were caused by occurrence of below zero temperatures in leafing stage. Since then, many shoots came out at accessary bud on proximal and the top part of the branches. Therefore, frost damage of mulberry tree in Buan province in 2010 was caused by occurrence of below zero temperatures on April and topographic characteristics of orchard.

• Journal of the Korean Society of Costume
• /
• 제28권
• /
• pp.65-84
• /
• 1996

The purpose of this study is to analyze the relation between the beauty of human body and the fashion illustration in each period And I attained my object through the investigation of features and changes of illustration which is given a vivid description of the features and development of ideal humam body beauty. By various methods I studied this subject. Frist I refered to sundry records Secondly I investiated the fashion illustrations which are included in Vogue. On the basis of this data I grasped the ideal types of human body beauty which is founded during the social change in each 10 years. And I analyzed the relation be-tween the ideal type and fashion illustration which show the change of fashion. The summary of result is as follows. 1. In the early part of the 20th century the beauty of human body is represented with the figure of large-sized beauty which emphasize shoulder and bust. And fashion ikllustration show 9 life-size broad shoulder full bust lim waist and hourglass silhouette. 2, In the 1910s the swell of strength vanishes gradually and shoulder and sleeve are straight type. And fashion illustration show 7 life-size high waist line. And that is tublar sil-houette of high waist and streamline shape in which bust and hip are not emphasized. 3. In the 1920s the ideal type of human body beauty is straight type which shows flat bust and unexaggerate hip. And fashion illus-tration is about 8 life-size tublar silhouette of low waist and lunger and slimmer and young style in which bust and hip are not emph-asized. 4. In the 1930s the ideal is womamly slim and long style. Fashion illustration is about 8 life-size and slim & long silhouette in which waist line is emphasized and bust and hip line come out. 5. In the 1940s the ideal type is womamly style which has narrow shoulder rich bast and slim waist. And fashion illustration is about 7 life-size and hourglass silhouette which has unartificial shoulder slim waist and empha-sized bust. 6. In the 1950s the ideal type is that of ro-bust health which emphasize build and muscu-lar system. And fashion illustration is 8.5 life-size and show full bust and made waist slimmer. That is sheath silhouette. 7. In the child who has full face with large eyeball slender and long leg: narrow and immatured body comparatively big head. And fashion illus-tration is 7 life-size and show slim and long neck flat bust long and slim limbs and big head. That is H type silhouette. 8. In the 1970s the ideal type is high stat-ure flat breast small hip and wide shoulders. And fashion illustration is wide shoulders and slim waist as 11 life-size and straight sil-houete. 9. In the 1980s the ideal type is extremely emphasized breadth of shoulder because healthy body and muscle are recognized as the symbol of ideal attractiveness. And fashion il-lustration is about 8.5 life-size and show mus-cular slim type that is slim silhouette. 10 At the present time the ideal type is slim and tall type which is empasized healthy beauty. And fashion illustration is 12 life-size which has healthy body and skin So that is slim and long type.

• The Journal of Korean Society for Radiation Therapy
• /
• 제19권1호
• /
• pp.55-62
• /
• 2007

Purpose: Digital medical image commenced with an introduction of PACS has become more popular today in the radiation diagnosis and medical treatment and made great progress, in particular, for medical testing field, whereas it has made slow progress for radiation therapy area. In order to accommodate the current trend of digital from analog, a spherical type mechanical check device (SMCD) that is form of spherical differing from the existing form of flat or cube has been designed and tested its practicability to replace the part in mechanical check with digital image from QA operation. Materials and Methods: If the distance maintains constant between source(target) and image detector with constant distance to the center of spherical type mechanical check device(SMCD), the size will be shown as a constant image at all times regardless of its direction exposed. For the test, two accurate hemispheres are made and put together which results in a sphere of the equilateral circle. Results: It enables a variety of implementation of the existing mechanical check using digital image as follows: congruity level of radiation field and light field, size accuracy of radiation field and collimation field, gantry rotation isocenter check, collimation rotation isocenter check, room laser accuracy check, collimation rotation angle check, couch rotation angle check, and more. Conclusion: It has proved its practicability in checking isocenter congruity level as real time at the time of simultaneous rotation between gantry and couch that is applied to the non-coplanar field, which had been hard to apply as a device formed of existing flat or cube.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• 제35권2호
• /
• pp.145-152
• /
• 2011

The performance of flat-tube radiators with louvered fins was numerically investigated for different tube insertion lengths. The results of numerical analysis using CFX-11 were compared with experimental results. In this study, three types of flat-tube radiators with louvered fins were considered. An experiment was conducted to validate the numerical results. Flow rate ratio (FR) and Stotal were introduced to understand the uniformity of flow distribution easily. The results of numerical analysis revealed that the heat transfer rate and pressure drop increased as the mass flow rate increased. Further, the results showed that the heat transfer rate of sample 3 with h/D = 0.5 was higher than that of the other samples. The pressure drop increased as the insertion length toward the header part increased, and the pressure drop in the case of sample 3 appeared to be the highest. The factor Stotal showed that the uniformity of the flow distribution in the case of sample 1 with h/D = 0 was higher than that in the case of the other samples.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• 제43권6호
• /
• pp.723-734
• /
• 2010

To understand temporal variations in geochemical characteristics of intertidal surface sediments around Byeonsan Peninsula (in the middle of the western coast, Korea) after the construction of Saemanguem dyke, the sedimentation rate and various geochemical parameters, including mean grain size (Mz), water content (WC), ignition loss (IL), chemical oxygen demand (COD), and acid volatile sulfide (AVS), were measured along four transects (A.D lines) at monthly intervals from February 2008 to March 2009. The average monthly sedimentation rate ranged from -5.3 to 3.8 mm/month (mean $-0.8{\pm}2.7\;mm$/month), which showed an erosion-dominated environment in the lower part of the intertidal zone. In addition, surface sediments were eroded in summer and autumn, but were deposited in spring and winter. The Mz of surface sediments ranged from -0.8 to $3.4{\varnothing}$ (mean $2.8{\pm}0.5{\varnothing}$), indicating that the surface sediments consist of coarser sediments (sand and slightly gravelly sand). The Mz of surface sediments did not show large monthly and/or seasonal variations, although the sedimentation rates of surface sediment showed large seasonal variation. This may be due to lateral shifting and effective dispersion of surface sediments by wind, tide, and longshore current. The concentrations of IL and COD in the surface sediments ranged from 0.2 to 2.9% (mean $1.4{\pm}0.4%$) and from 0.2 to $18.5\;mgO_2$/g-dry (mean $3.9{\pm}3.4\;mgO_2$/g-dry), respectively, which were slightly higher in spring than in the other seasons. This may be related to spring blooms of phytoplankton in seawater and/or benthic microalgae in surface sediments. On the other hand, no AVS concentrations were detected in surface sediments at any of the sampling stations during the study period.

• Applied Chemistry for Engineering
• /
• 제25권4호
• /
• pp.401-408
• /
• 2014

In membrane bio-reactor (MBR), the aeration control is one of the important independent variables to decrease fouling and to save energy with shear stress change on the membrane surface. The paper was carried out for numerical simulation of 3-dimensional fluid flow phenomena of the cylindrical bioreactor with submerged flat membranes equipped in the center and supplied the air from the bottom by using the COMSOL program. The viscosity and temperature of solution were assumed to be constant, and the specific air demand based on permeate volume ($SAD_p$) defined as scouring air per permeate rates was used as a variable. The calculated CFD velocities were compared with those of the velocity meter measurement and video image analysis, respectively. The results were good agreement each other within 11% error. For fluid flow in the reactor the liquid velocity increased rapidly between the air diffuser and membrane module, but the velocity decreased during flowing of the membrane module. Also, the velocity increased as it was near from the reactor wall to the central axis. The calculated shear stress on the membrane surface showed the highest value at the center part of the module bottom side and increased as aeration rate increased. Especially, the wall shear stress increased dramatically as the aeration rate increased from 0.15 to 0.25 L/min.

• Trans-
• /
• 제2권
• /
• pp.161-190
• /
• 2017

As times progress, creative change is achieved by attempts to embrace different needs. These attempts are expressed as the form of an Object which pulls down the barriers of genre between art. There is now in fact difficult to find a work that doesn't contain the characteristic of an Object. The necessity of this study is that it tries to approach an Object with a holistic perspective and understand it as a single system. It also tries to analyze the roles that an Object's characteristic and expression and the research ways they influence the dance work by contemplating the aesthetic discussion process of an Object in the art field. Also, by researching the characteristics of expression and how Objects stimulate a dance work, this study will take an important part in developing the dance works. Based on this necessity, this research choose the works of William Forsythe, (2006), (2009), (2009) which clearly depicts the expression characteristics of an Object. It is noted that the usage of an Object maximized creativity and brought expansion of expressions in a dance performance by using diverse mediums, body actions and even nonmaterial components without losing the essence of a dance. As a result, this usage of an Object provides theories that bring the enlargement of expression and suggests various ways to overcome the limits of other existing dance works.

• Fire Science and Engineering
• /
• 제25권6호
• /
• pp.83-88
• /
• 2011

This study presented the structure and characteristics of vinyl cords used for wiring electric equipment and appliances and analyzed the photographs of damaged flat-type vinyl cords (VFF, $1.25mm^2$) and the metallic cross-sectional structure of melted conductors. Normal VFFs were made by twisting several strands together and the surface of the conductor was red brown. In addition, from the analysis of the metallic structure of the conductor, it was found that its grains had been elongated. The surface of a VFF damaged by normal flame showed no sheen with carbonized insulation material fused on the conductor surface. In addition, from the analysis of the cross-sectional structure of the melted area, it was found that voids of a certain shape were formed on it but that the cord's own elongation structure could not be checked. The cross-sectional analysis of the melted conductor damaged by the external flame applied to a VFF to which electric current was being applied showed no elongation structure for each cord, and revealed that irregular voids and a columnar structure had grown. The surface of the VFF damaged by overcurrent was uniformly carbonized and the cross-sectional structure analysis of the melted conductor revealed that the dendritic structure had grown. The analysis of the characteristics of the VFF melted by short-circuit showed that even though some part of the surface was contaminated, it showed little sheen and that the area rebounded by melting was round in shape. In addition, the cross-sectional structure analysis using a metallurgical microscope showed the boundary surface and columnar structure and revealed an amorphous structure like normal copper at areas other than the melted conductor.

• Animal Systematics, Evolution and Diversity
• /
• nspc2호
• /
• pp.233-241
• /
• 1988

The crab, Macrophthalmus (Mareotis ) japonicus , collected in 1983 from CHojijin tidal flat, southeastern part of Kangwha Island , Korea, was studied. Its caraace breadth, the carapace length , and body height were checked , and the measured raw data were analysed for the growth ratios by the mode subtraction method from the frequency distribution compared with the probability graphs. The growth rate of the crab rose more in summer than in fall and exceeded 10% during the same period on Chojijin tidal flat in Kangwha Island , Korea. Four size groups of the crab appeared in June, 1983 , but they were put together into only on emixed group by autumn. The rapid growth of the crab in summer in middle latitude comes from the seasonal bio-rhythm and the best conditions for food. But the physiological activities of the crab are reduced from autumn and the growth rate reaches the upper limits in many individuals on this tidal flat. The more the crabs grow, the more the breadth ratios to the carapac length become larger and the slopes of correlation curve get smaller. The measured values from the carapace breadth of the crab are more useful for morphological studies than those values from the carapace length or body height.