• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2002년도 International Meeting on Information Display
• /
• pp.803-806
• /
• 2002

Flame spray pyrolysis was applied to improve the photoluminescence characteristics of blue-emitting $Sr_5(PO_4)_3Cl:Eu^{2+}$ phosphor particles with high brightness for the application to LED phosphor. $Sr_5(PO_4)_3Cl:Eu^{2+}$ prepared from conventional spray pyrolysis had poor PL intensity than that of commercial products under long-wavelength ultraviolet(UV). $Sr_5(PO_4)_3Cl:Eu^{2+}$ phosphor particles prepared by flame spray pyrolysis had PL intensity as same as that of commercial products under long-wavelength UV. Hollow morphology and porous structure of the particles prepared by the flame spray pyrolysis disappeared after posttreatment. Even though the $Sr_5(PO_4)_3Cl:Eu^{2+}$ phosphor particles prepared by the flame spray pyrolysis had irregular shape, the particles had dense structure and clear surface property.

• 한국재료학회지
• /
• 제14권8호
• /
• pp.600-606
• /
• 2004

$Zn_{2}SiO_{4}:Mn$ phosphor particles were prepared by a flame spray pyrolysis method. It has been generally known that the high-temperature flame enables fast drying and decomposition of droplets. In the present investigation, the morphology and luminescent property of $Zn_{2}SiO_{4}:Mn$ phosphor were controlled in a severe flame preparation condition. The particle formation in the flame spray pyrolysis process was achieved by the droplet-to-particle conversion without any evaporation of precursors, which made it possible to obtain spherical $Zn_{2}SiO_{4}:Mn$ particles of a pure phase from a droplet. Using colloidal solutions wherein dispersed nano-sized silica particles were adopted as a silicon precursor. $Zn_{2}SiO_{4}:Mn$ particles with spherical shape and filled morphology were prepared and the spherical morphology was maintained even after the high-temperature heat treatment, which is necessary to increase the photoluminescence intensity. The $Zn_{2}SiO_{4}:Mn$ particles with spherical shape, which were prepared by the flame spray pyrolysis and posttreated at $1150^{\circ}C$, showed good luminescent characteristics under vacuum ultraviolet (VUV) excitation.

• 한국세라믹학회지
• /
• 제41권3호
• /
• pp.242-246
• /
• 2004

화염분무열분해(FSP) 공정을 이용하여 결정질의 좁은 입도분포를 가지는 $\alpha$-알루미나 나노입자를 제조하였다. 초미분의 액적을 형성시키기 위해 전구체 용액으로서 연료인 등유를 연속상으로 하고 산화제인 알루미늄 질산염 수용액을 분산상으로 하는 유중수적(W/O)형의 마이크로에멀전을 제조하였다 0.5M 농도의 알루미늄 질산염 수용액을 10vol%, 등유 80vol%, 그리고 유용성 유화제 10vol%를 혼합하여 안정한 분산상태를 가지는 마이크로에멀전을 제조한 후, 이류체 노즐 분무기를 사용하여 0.03㎫의 공기 압력으로 분무하여 화염에 직접 노출시켰다. 제조된 생성물은 20에서 30 나노미터의 균일한 크기를 가지는 $\alpha$-알루미나 상으로 확인되었다.

• 자원리싸이클링
• /
• 제14권6호
• /
• pp.37-43
• /
• 2005

페리튬이온전지로부터 회수된 코발트와 리튬 침출액으로부터 화염분부열분해법에 의하여 $LiCoO_{2}$ 나노분말을 제조하였다. 리튬 및 코발트 성분을 함유하는 전극물질은 열처리 및 기계적 처리에 의해 그 농도를 증가 시켰다. 리튬이온전지 양극물질을 질산으로 용해한 다음 침출액중 Li과 Co의 당량비가 1.0 되도록 $LiNO_{3}$로 조절하여 화염분무열분해용 전구체를 제조하었다. 화염분무열분해법에 의해 제조된 $LiCoO_{2}$ 분말의 평균입자크기는 전구체의 몰 농도가 증가하면서 증가되었으며, 화염온도 역시 입자의 크기를 증가시켰다. 변수실험 결과 $11{\~}35nm$ 크기의 결정형 $LiCoO_{2}$ 나노분말을 제조할 수 있었다 또한 나노 $LiCoO_{2}$의 전극재료로서의 가능성을 확인하기 위하여 충방전 특성 평가와 같은 전기화학적 분석을 수행하였다.

• 한국재료학회지
• /
• 제18권2호
• /
• pp.77-83
• /
• 2008

Green-emitting $Ba_{1.468}Sr_{0.5}SiO_4\;:\;Eu_{0.012},\;Y_{0.02}$ phosphor powders under long-wavelength ultraviolet light were prepared via high-temperature flame spray pyrolysis from spray solutions with and without $NH_4Cl$ flux. The effects of the temperature of the diffusion flame and the $NH_4Cl$ flux on the morphologies, crystal structures and photoluminescence intensities of the $Ba_{1.468}Sr_{0.5}SiO_4\;:\;Eu_{0.012},\;Y_{0.02}$ phosphor powders were investigated. The phosphor powders obtained from the spray solution with the $NH_4Cl$ flux had higher photoluminescence intensities compared to phosphor powders obtained from the spray solution without the flux. The photoluminescence intensity of the phosphor powders obtained from the spray solution without the flux decreased as the flow rate of the fuel gas increased. On the other hand, the photoluminescence intensity of the phosphor powders obtained from the spray solution with the flux increased as the flow rate of the fuel gas increased. The difference of in the phase purity and morphology of the powders affected the photoluminescence intensities of the phosphor powders.

• 센서학회지
• /
• 제29권2호
• /
• pp.112-117
• /
• 2020

Xylene is a hazardous volatile organic compound that should be precisely measured to monitor indoor air quality. However, the selective and sensitive detection of ppm-level xylene using oxide-semiconductor gas sensors remains a challenge. In this study, pure and Cr-doped Co₃O₄ nanoparticles (NPs) were prepared using flame spray pyrolysis, and their gas-sensing characteristics to 5-ppm xylene at 250 ℃ were investigated. The 4 at% Cr-doped Co₃O₄ NPs exhibited a high gas response to 5-ppm xylene (resistance ratio to gas and air = 39.1) and negligible cross-responses to other representative and ubiquitous indoor pollutants such as ethanol, benzene, formaldehyde, carbon monoxide, and ammonia. In this paper, the enhancement of the gas response and selectivity of Co₃O₄ NPs to xylene by Cr doping was discussed in relation to the catalytic promotion of the gas-sensing reaction. This sensor can be used to monitor indoor xylene.

• 한국전기전자재료학회논문지
• /
• 제25권8호
• /
• pp.626-631
• /
• 2012

$SnO_2$ nanoparticles were synthesized by flame spray pyrolysis, which were directly deposited on Pt interdigitated substrates. Gas sensing performance was evaluated for various gases such as $H_2$, CO, $H_2S$, and $NH_3$, and it was compared with that of commercial $SnO_2$ nanopowder. The synthesis of $SnO_2$ nanoparticles was also conducted in various solvents. As a result, the primary particle size was changed with the solvent of precursor solution, and their $H_2$ sensing properties were significantly affected.

• 한국입자에어로졸학회지
• /
• 제5권1호
• /
• pp.1-7
• /
• 2009

Fe- and V-doped titanium dioxide nanoparticles consisting of spherical primary nanoparticles were synthesized from a mixed liquid precursor by using the flame spray pyrolysis. The effects of dopant concentration on the powder properties such as morphology, crystal structure, and light adsorption were analyzed by TEM, XRD, and UV-Vis spectrophotometer, respectively. As the V/Ti molar ratio increased, pure anatase particles were synthesized. On the contrary, rutile phase particles were synthesized as the Fe/Ti ratio increased. Photocatalytic property of as-prepared $TiO_2:Fe,V$ nanoparticles was investigated by measuring the removal efficiency for volatile organic compounds (VOCs) under the irradiation of visible light. After 2 hrs under visible light, the removal efficiencies of benzene, p-xylene, ethylbenzene, and toluene were reached to 21.9%, 21.4%, 19.8% and 17.6% respectively.

• 대한기계학회논문집B
• /
• 제33권2호
• /
• pp.116-123
• /
• 2009

Carbon black, activated carbon and carbon nanotube have been used as supporting materials for precious metal catalysts used in fuel cell electrodes. One-step flame synthesis method is used to coat 2-5nm Pt dots on flame-generated carbon particles. By adjusting flame temperature, gas flow rates and resident time of particles in flame, we can obtain Pt/C nano catalyst-support composite particles. Additional injection of hydrogen gas facilitates pyrolysis of Pt precursor in flame. The size of as-incepted Pt dots increases along the flame due to longer resident time and sintering in high temperature flame. Surface coverage and dispersion of the Pt dots is varied at different sampling heights and confirmed by Transmission electron microscopy (TEM), Energy-dispersive spectra (EDS) and X-ray diffraction (XRD). Crystalinity and surface bonding groups of carbon are investigated through X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy.

• 대한금속재료학회지
• /
• 제48권6호
• /
• pp.570-574
• /
• 2010

Silver conducting films were formed from nano-sized silver powders and glass frits prepared by flame spray pyrolysis. The mean sizes of the silver powders and glass frits were 73 and 63 nm, respectively. Nano-sized glass frits improved the adhesion strength of the silver conducting film to the glass substrate. The densities of the silver conducting films increased by increasing the glass contents of the films at firing temperatures of 400 and $500{^{\circ}C}$. The specific resistances of the silver conducting films with 5 wt.% glass of silver component were 7.8, 4.2 and 2.4 cm at firing temperatures of 400, 450 and $500{^{\circ}C}$.