• Journal of Korean Society of Water and Wastewater
• /
• v.31 no.2
• /
• pp.177-186
• /
• 2017

This study concerned the analysis on the efficiency of the conversion of water tank type supply system to direct water supply system to examine the feasibility of the conversion, as well as the calculation of optimal conversion range that enables the supply of safe, high-quality water at stable pressure in accordance with the standards of water supply facility. The results of this research showed that when converting water supply system from water tank type supply system to direct water supply system, more nodal points could be properly converted and more reduction of electricity usage was expected in case water pressure rather than residence time was fixed. This means that higher efficacy can be obtained by fixing water pressure when converting water supply system. However, since the number of the locations that received on-spot inspection was small and the electricity usage measured was not exclusively by water supply facility, it is difficult to judge that such reduction of electricity usage accurately represents reduced electricity usage by water supply facility alone. therefore, after having secured on-spot information about a larger number of locations in apartment complexes that have converted water supply system, and utilizing information about electricity usage exclusively by water supply facility, the proposed method of this research could be applied to accurately deducing expected reduction of electricity usage by water supply facilities of various other apartment complexes. It is also considered possible to deduce an effective operation method of water supply system by finding out an area that shows low pressure or low residual chlorine concentration in the optimal conversion range of water supply, followed by estimating the proper location of pumping station or the proper chlorine dosage at the power purification plant that supply water to the target area.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.4
• /
• pp.53-61
• /
• 2017

Turbocharger is a device for increasing the power of a vehicle engine. The control plate is the main component for fixing the vane of the turbocharger. Now, the control plate is made of austenite steel cutting after the casting process. It has excellent corrosion, heat resistance and mechanical characteristics of material. However, present the process is made by cutting after casting. when cutting is processed after casting, so materials, processing time, and processing energy are lost. Therefore, this study proposes a process to powder compact use of stainless steel Deklak2 and to minimize amount of cutting through net shape process. The mechanical properties of Deklak2 were verified by tensile test, hardness test and relative density measurement, and the governed equation was defined. Also, the curvature radius 1, 2 and the density, affects the shape, were selected as the design parameters, and the best process conditions was proposed through the Taguchi method and the evaluation of SN ratio. And then prototype molds were fabricated and compared with the results of the finite element analysis for the verification, and it was found that the tendency of relative density and dimension was coincided. Therefore, it was found that the amount of cutting can be minimized by only the net shape process after the sintering process and it can be applied to mass production.

• Transactions of Materials Processing
• /
• v.17 no.2
• /
• pp.124-129
• /
• 2008

Net shape forging technologies give many effects into the costs and qualities for the finished products. So, the studies to reduce the additional machining amount are very important in forging industry. Specially, there are two main topics in cold forging industry, such as, tool life and precision forging. In this study, new forging technique was proposed to eliminate the machining process for fixing up the length and improve the lead accuracy of gear. The luck-up hub is manufactured through many processes, such as upsetting, piercing and direct extrusion. The gear is formed in direct extrusion process; however, lead accuracy of the gear is over allowance limit. Therefore, the additional sizing process must be added. In this study, process design for closed-die forging of a lock-up hub used for a component of automobile transmission was made using three-dimensional finite element simulations, and the strain distributions and velocity distributions are investigated through the post processor. The rigid-plastic finite-element method for back pressure forging has been used in order to reduce development time and die cost. Using the FEM simulation, we found the optimum value of back pressure. The prototypes of lock-up hub parts were forged into the net-shape. In the experiment, lead precision of tooth are measured by the CCMM(Contact Coordinate Measuring Machine). The dimensional accuracy of forged part was improved up to the 40% when back press was applied.

• Journal of the Korean BIBLIA Society for library and Information Science
• /
• v.12 no.1
• /
• pp.43-64
• /
• 2001

The purpose of this study was to measure performance of university libraries, especially investigating the components of service quality and their relationship to the customer satisfaction. The result of the statistical analyses is summarized as follows： The result of 5 point scale study shows the following degree of satisfaction in 55 components： timeliness of circulation, processing of fine. location of library, usefulness of retrieval system, library user education, speed of retrieval. number of terminals, and cleaning. On the other hand, shows the following degree of dissatisfaction in 55 components： speed of civil petitions, hour for program use, result of civil petitions, fixing of library user education, speed of retrieval, method of public relation, waiting time for Internet use, and use of the other library materials. Also. customers’matters of weight and importance was availability. learning facilities, suitable collections, circulation, and system of retrieval.

• Journal of Microbiology and Biotechnology
• /
• v.23 no.4
• /
• pp.572-578
• /
• 2013

Azotobacter vinelandii, a strict aerobic nitrogen-fixing bacterium, has been extensively studied with regard to the ability of $N_2$-fixation due to its high expression of nitrogenase and fast growth. Because nitrogenase can also reduce cyanide to ammonia and methane, cyanide degradation by A. vinelandii has been studied for the application in the bioremediation of cyanide-contaminated wastewater. Cyanide degradation by A. vinelandii in NFS (nitrogen-free sucrose) medium was examined in terms of cell growth and cyanide reduction, and the results were applied for cyanide-contaminated cassava mill wastewater. From the NFS medium study in the 300 ml flask, it was found that A. vinelandii in the early stationary growth phase could reduce cyanide more rapidly than the cells in the exponential growth phase, and 84.4% of cyanide was degraded in 66 h incubation upon addition of 3.0 mM of NaCN. The resting cells of A. vinelandii could also reduce cyanide concentration by 90.4% with 3.0 mM of NaCN in the large-scale (3 L) fermentation with the same incubation time. Finally, the optimized conditions were applied to the cassava mill wastewater bioremediation, and A. vinelandii was able to reduce the cyanide concentration by 69.7% after 66 h in the cassava mill wastewater containing 4.0 mM of NaCN in the 3 L fermenter. Related to cyanide degradation in the cassava mill wastewater, nitrogenase was the responsible enzyme, which was confirmed by methane production. These findings would be helpful to design a practical bioremediation system for the treatment of cyanide-contaminated wastewater.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.8
• /
• pp.1068-1075
• /
• 2018

In this paper, a novel PLL has been proposed that reduces the size of the loop filter while suppressing spur by using a VCO with two inputs. Through the stability analysis according to the operating status, the PLL is designed to operate stably after the phase fixing. The capacitor of loop filter usually occupies larger area of PLL. It is a VCO that can reduce the size of the loop filter by increasing the effective capacitance of the capacitor through the simultaneous charge and discharge operation by two charge pumps and has two signals operating in opposite phases. The settling time of set to $80{\mu}s$ approximately by using a LSI(Locking Status Indicator) indicating the phase locking status. The proposed PLL is designed using a supply voltage of 1.8V and a $0.18{\mu}m$ CMOS process.

• Journal of Practical Engineering Education
• /
• v.7 no.2
• /
• pp.119-123
• /
• 2015

ABS material is easy to process, impact resistance and heat resistance is strong. ABS material is often used as a substitute for the interior and exterior metal material for an automobile. As the demand of ABS increases, fabricating education using ABS has also been increasing its importance. As part of its education, ABS material is used in the mold fabricating part of the regional and national skills competition. At this time, the force of the vise for fixing the ABS material in the processing using the ABS material can affect the final shape after machining. However, it has not been an accurate description of the notes and instructions of working in education. Therefore, in this study, we study the impact the force of vise affect structural shape in the fabricating education using ABS material and during fabricating education of ABS material, trying to present the notes of the appropriate it.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.682-685
• /
• 2017

An experimental study was carried out to investigate the injection characteristics of non-circular effervescent type twin-fluid nozzles. For this purpose, two types of non-circular nozzles (E1, E2) and one kind of circular nozzle (C) were used. At this time, the Aerorator mounted on the nozzle used three different diameters to match the aspect ratio with the nozzle exit area. Therefore, experiments were performed according to three aspect ratios for each nozzle, and a total experiments were conducted. Experiments were carried out by controlling the amount of air flowing after fixing the flow rate of the liquid, and the nozzle internal pressure and SMD were measured, and the jet image was taken from the nozzle. The discharge coefficients of the three kinds of nozzles were compared with the conventional equation and the Jedelsky's equation, and the Jedelsky's equation was found to be about 4 times larger. The droplet size (SMD) injected from the nozzle was found to be smaller in the non-circular shape than in the circular shape, which is expected to be caused by the difference of the discharge coefficient values.

• The Journal of the Society of Korean Medicine Diagnostics
• /
• v.13 no.2
• /
• pp.14-23
• /
• 2009

In the Ki-Gu(氣口) pulse and the Yin-Yeong(人迎) pulse are the arterial pulsation position of the Lung Channel of Hand-Taeuem(手太陰) and the Stomach Channel of Foot-Yangmyeong(足陽明). At the pulses we can examine the circulation of Ki-Hyeol(氣血), the balance of Uem-Yang(陰陽), the deficiency and excess of the diseases, whether the disease is in Uem-Channel(陰經) or Yang-Channel (陽經), whether the disease is internel injury or externel injury. In the Ki-Gu(氣口) pulse and the Yin-Yeong(人迎) pulse are in front of the Right-Kwan(右關) and the Left-Kwan(左關) the distance of 1 Pun(分) because of completion of the Chon-Ku-Pulse-Taking(寸口脈診). The purpose of examnation is same to . In the Kwan-Pulse(關脈) doesn't have the position. It has only the role of a gateway of the circulation of Ki-Hyeol(氣血), the balance of Uem-Yang(陰陽). And it is same to role of the Ki-Gu(氣口) pulse and the Yin-Yeong(人迎) pulse in . So we can think that the Kwan-Pulse(關脈) in and the Ki-Gu(氣口) pulse and the Yin-Yeong(人迎) pulse in are the same thing. And we must have the different standard when examine the condition of Sam-Cho(三焦) and the circulation of Ki-Hyeol(氣血), the balance of Uem-Yang(陰陽) because the position of the Kwan-Pulse(關脈) came out after the time of .

• Design & Manufacturing
• /
• v.11 no.3
• /
• pp.19-24
• /
• 2017

In these days, increase requirement of TEM (Transmission Electro Microscope) in not only scientific field but also industrial field. Because TEM can measure inner-structure of specimen a variety of materials like metal, bio. etc. When use TEM, specimen should be thin about 50nm. So making for thin specimen, use Ion milling device that include specimen holder. The holder generally made of Aluminium Aluminium holder is worn away easily. For this reason, using time of ion milling with aluminum holder is too short. To solve the problem, we replace aluminium holer to molybdenum alloy holder. In this paper, we design molybdenum alloy holer for CAM and modify CAD modeling for effective machining process. So we array a specimen 3 by 4 and setup orientation for one-shot machining process. Next we make a CAM program for machining. we making a decision two machining strategy that chose condition of tool-path method, step-down, step-over. etc. And then conduct machining using CNC milling machining center. To make clear difference between case.1 and case.2, we fixed machining conditions like feed-rate, main spindle rpm, etc. After machining, we confirm the condition of workpiece and analysis the problems case by case. Finally, case.2 work piece that superior than case.1 cutting with WEDM because that method can not ant mechanical effect on workpiece.