• Journal of the wind engineering institute of Korea
• /
• v.22 no.4
• /
• pp.163-169
• /
• 2018

In this study, wind loads exerted on the offshore wind turbine rotor in parked condition were predicted with variations of wind speeds, yaw angles, azimuth angle, pitch angles, and power of the atmospheric boundary layer profile. The calculated wind loads using blade element theorem were compared with those of estimated aerodynamic loads for the simplified blade shape. Wind loads for an NREL's 5 MW scaled offshore wind turbine rotor were also compared with those of NREL's FAST results for more verification. All of the 6-component wind loads including forces and moments along the three axis were represented on a non-rotating coordinate system fixed at the apex of rotor hub. The calculated wind loads are applicable for the dynamic analysis of the wind turbine system, or obtaining the over-turning moment at the foundation of support structure for wind turbine system.

• Journal of the Korea Society for Simulation
• /
• v.29 no.2
• /
• pp.119-127
• /
• 2020

This study numerically investigated a structural behavior subjected to consecutive explosions. To this end, a small scale one-way reinforced slab (RC) with fixed-fixed boundary condition was considered as the target structure, and a commercial software, LS-DYNA, was utilized for finite element (FE) analysis. Prior to performing FE analysis, preliminary tests were carried out to verification of a computational model for the one-way RC slab. In the numerical simulation, identical blast loads were consecutively applied to the structure, and cumulative damage assessment were carried out based on its maximum dynamic displacements. As a result of the numerical simulation, it was found that maximum displacements considering permanent deformation due to a prior explosion were almost linearly increased in every explosion until the hazardous damage threshold.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.419-419
• /
• 2016

High efficiency silicon solar cell requires the textured front surface to reduce reflectance and to improve the light trapping. In case of mono-crystalline silicon solar cell, wet etching with alkaline solution is widespread. However, the alkali texturing methods are ineffective in case of multi-crystalline silicon wafer due to grain boundary of random crystallographic orientation. The acid texturing method is generally used in multi-crystalline silicon wafer to reduce the surface reflectance. However the acid textured solar cell gives low short-circuit current due to high reflectivity while it improves the open-circuit voltage. To reduce the reflectivity of multi-crystalline silicon wafer, double texturing method with combination of acid and reactive ion etching is an attractive technical solution. In this paper, we have studied to optimize RIE experimental condition with change of RF power (100W, 150W, 200W, 250W, 300W). During experiment, the gas ratio of SF6 and O2 was fixed as 30:10.

• Journal of the Korean Vacuum Society
• /
• v.14 no.1
• /
• pp.7-16
• /
• 2005

Oil-Hydraulic pump consisting of swing twin-cylinder becomes to be used as a next generation of low vacuum pump. However, there is no enough flow-analysis for design improvement. It is essential to develope a numerical method for flow-analysis before manufacturing, in economic sense. Using a commercial code (Fluent), developed for flow-analysis, useful informations for design of pump were provided. Two-dimensional analysis has been performed to investigate the flow parameters such as pressure and velocity distributions between the swing twin-cylinder and the fixed cylinder. This numerical method will be used to design a better performance of pump consisting of swing twin-cylinder.

• Journal of Korea Water Resources Association
• /
• v.30 no.6
• /
• pp.761-768
• /
• 1997

A numerical model is developed to analyze the incompressible unsteady flow induced by the pump trip-out in the cooling water discharge culvert of thermal power plants. The numerical models has various features to deal concureently with the overall behavior of complicated unsteady flow due to the presence of cooling water internal system, seal well, air chamber, culvert, manholes, open channel and sea water. A leap-frog finite difference scheme is employed to solve governing equations, and the model is tested for a simple case of two tanks connected with a pipe. A fixed free surface boundary condition used earlier at the downstream end of culvert for large water body is investigated.

• 한국전산유체공학회:학술대회논문집
• /
• 2005.10a
• /
• pp.117-124
• /
• 2005

Splitting algorithms of the incompressible Navier-Stokes equations using P1P1/P2P1 finite element formulation are newly proposed. P1P1 formulation allocates velocity and pressure at the same nodes, while P2P1 formulation allocates pressure only at the vertex nodes and velocity at both the vertex and mid nodes. For comparison of the elapsed time and accuracy of the two methods, they have been applied to the well-known benchmark problems. The three cases chosen are the two-dimensional steady and unsteady flows around a fixed cylinder, decaying vortex, and impinging slot jet. It is shown that the proposed P2P1 semi-splitting method performs better than the conventional P1P1 splitting method in terms of both accuracy and computation time.

• Tribology and Lubricants
• /
• v.23 no.4
• /
• pp.170-174
• /
• 2007

Wear and scuffing tests were conducted using friction and wear measurement of piston rings and cylinder blocks in low friction diesel engine. The frictional forces, wear amounts and cycles to scuffing in boundary lubricated sliding condition were measured using the reciprocating wear tester. The cylinder blocks were used as reciprocating specimens, and the piston rings with several coatings were used as fixed pin. Several coatings were used such as DLC, TiN, Cr-ceramic and TiAlN in order to improve the tribological characteristics. From the tests wear volume of piston ring surfaces applied various coatings were compared. During the tests coefficients of friction were monitored. Test results showed that DLC coatings showed good tribological properties. TiN and Cr-ceramic coated rings showed good wear resistance properties but produced high friction.

• Proceedings of the KSRS Conference
• /
• v.1
• /
• pp.138-141
• /
• 2006

In developing algorithms to retrieve the sea surface temperature (SST) and sea surface wind speed from the Advanced Microwave Scanning Radiometer (AMSR) aboard the AQUA and the Advanced Earth Observation Satellite-II (ADEOS-II), data from the SeaWinds aboard ADEOS-II were helpful. Since features of the ocean microwave emission (Tb) related with ocean wind are not well understood, in case of using only AMSR data, combination of AMSR and SeaWinds revealed pronounced features about the ocean Tb. Two results from combinations of the two sensors were shown in this paper. One result was obtained at wind speeds over about 6m/s, in which the ocean Tb varies with the air-sea temperature difference, even though the SeaWinds wind speed is fixed at the same values. The ocean Tb increases as the air-sea temperature difference becomes negative, i.e., the boundary condition becomes unstable. This result indicates that the air temperature should be included in AMSR SST algorithm. The second result was obtained from comparison of two wind speeds between AMSR and SeaWinds. There is a small difference of two wind speeds, which might be related with several mechanisms, such as evaporation and plankton.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.676-679
• /
• 2008

Numerical simulations of fluid injection into particulate materials were conducted to observe cavity initiation and propagation using distinct element method. After generation of initial particles and wall elements, confining stress was applied by servo-control method. The fluid scheme solves the continuity and Navior-Stokes equations numerically, then derives pressure and velocity vectors for fixed grid by considering the existence of particles within the fluid cell. Fluid was injected as 7-step into the assembly in the x-direction from the inlet located at the center of the left boundary under confining stress condition, 0.1MPa and 0.5MPa, respectively. For each simulation, movement of particles, flow rate, fluid velocity, pressure history, wall stress including cavity initiation and propagation by interaction of flulid-paricles were analyzed.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.969-974
• /
• 2001

Circular cylindrical tubes are widely used in structures such as vehicles and aircraft structures, where light weight and high compressive/bending/torsional load carrying capacity are required. When axially compressed, relatively thick circular cylindrical tubes deform in a so-called ring mode. Each ring develops and completely collapses one by one until the entire length of the tube collapses. During the collapse process the tube absorbs a large amount of energy. Like honey-comb structures, circular cylindrical tubes are light weighted, are capable of high axial compressive load, and absorb a large amount of energy before being completely collapsed. In this report, the subject of axial plastic buckling of circular cylindrical tubes was reviewed first. Then, the axial collapse process of the tubes in a so-called ring mode was studied both experimentally and numerically. In the experiment, steel tubes were axially compressed slowly until they were completely collapsed. Fixed boundary condition was provided. Numerical study involves axisymmetric, elastic-plastic, large deflection, self-contact mechanisms. The measured and calculated results were presented and compared with each other. The purpose of the study was to evaluate the load carrying capacity and the energy absorbing capacity of the tube.