• 제목/요약/키워드: Fixed Density

검색결과 600건 처리시간 0.026초

LPS-SiC 세라믹스의 제조특성에 미치는 $SiQ_2$ 입자크기의 영향 (Effects of $SiO_2$ Particle-size on Fabrication Properties of LPS-SiC Ceramics)

  • 김성훈;윤한기;김부안
    • 한국해양공학회:학술대회논문집
    • /
    • 한국해양공학회 2006년 창립20주년기념 정기학술대회 및 국제워크샵
    • /
    • pp.162-165
    • /
    • 2006
  • In this study, Liquid Phase Sintered SiC (LPS-SiC) was fabricated by hot pressing method with $\beta$-SiC powder whose a particle size is 30nm and less on the average in argon condition at 1780 and $1800^{\circ}C$ under 20MPa. Alumina ($Al_2O_3$), yttria ($Y_2O_3$) and silica ($SiO_2$) were used for sintering additives. To investigate effects of particle-size and temperature on $SiO_2$, LPS-SiC was fixed $Al_2O_3$, $Y_2O_3$ and then particle-size of $SiO_2$ were changed as two kinds. The system of particle-size and temperature on sintering additives which affects a property of sintering os well os the influence depending on particle-size and temperature of sintering additives were investigated by measurement of sintering properties. Such as measurement of sintering density, vikers hardness and observing of microstructure were investigated to make sure of the optimum condition which is about matrix of $SiC_f/SiC$ composites. Base on the composition of sintering additives, microstructure and sintering property correlation, the effect of particle-size of sintering additives are discussed. An experimental method to investigate the dynamic characteristics of bums in extreme environmental condition is established.

  • PDF

비정질 InGaZnO4 박막의 전기적, 광학적 특성간의 상관관계 연구 (The Effect of Tail State on the Electrical and the Optical Properties in Amorphous IGZO)

  • 배성환;유일환;강석일;박찬
    • 한국세라믹학회지
    • /
    • 제47권4호
    • /
    • pp.329-332
    • /
    • 2010
  • In order to investigate the effect of tail state on the electrical and the optical properties in amorphous IGZO(a-IGZO), a-IGZO films were deposited at room temperature on fused silica substrats using pulsed laser deposition method. The laser pulse energy was used as the processing parameter. In-situ post annealing was carried out at $150^{\circ}C$ right after the film deposition. The $O_2$ partial pressure during the deposition and the post annealing was fixed to 10mTorr. The carrier mobility of the a-IGZO films had a range from 2 to $18\;cm^2/Vs$ at carrier concentrations greater than $10^{18}\;cm^{-3}$. As the laser energy density increased, the Hall mobility increased. And post annealing improved the Hall mobility, as well. The optical property was examined using the ultraviolet-visible spectroscopy. The a-IGZO films that have low Hall mobility exhibited stronger and broader absorption tails in >3.0 eV region. Post annealing reduced the intensity of the tail-like absorption. The absorption tail in a-IGZO films is an important factor which affects the electrical and the optical properties.

Treatment Effect of Mulberry Root-Bark (Mori radicis Cortex) Extract on Hypercholesterolemia in Rabbits

  • Kim Dong Kyu;Chai Hee-Youl;Kim Tae Myung;Lee Nam-Jin;Cho Jung-Hee;Park Jung-Hui;Kang Jong-Koo;Kim Yun-Bae;Hwang Seock-Yeon
    • 대한의생명과학회지
    • /
    • 제11권3호
    • /
    • pp.383-388
    • /
    • 2005
  • This study reports that the effect of Mori radicis cortex, Mulberry root-bark, on the lipid peroxidation products formation in the liver, blood serum and atherosclerosis of hypercholesterolemia rabbits fed Mulberry root-bark for eight weeks. The rabbits were permitted a fixed quantity to extract of Mulberry root-bark mixed hypercholesterol fodder. The lipid peroxidation products, malondialdehyde (MDA) was significantly diminished. Total cholesterol in serum worthily decreased. Also, triglyceride and high density lipoproteins (HDLs) increased after feeding Mori radicis cortex. Besides, thicky atheromatous plaque on the wall of aorta of rabbits fed on hypercholesterol diet were markedly attenuated by Mulberry root-bark extract. These results support and substantiate the extract of Mulberry root-bark as protection against lipid peroxidation in the liver, blood serum and atherosclerosis.

  • PDF

Study on Validity of 1-D Spherical Model on Aqua-plasma Power Estimation With Electrode Structure

  • 윤성영;장윤창;김곤호
    • 한국진공학회:학술대회논문집
    • /
    • 한국진공학회 2010년도 제39회 하계학술대회 초록집
    • /
    • pp.74-74
    • /
    • 2010
  • The aqua-plasma is the non-thermal plasma in electrical conductive electrolyte by generates the vapor film layer on the immersed metal electrode surface. This plasma can generate the hydroxyl radical by dissociate the water molecule with the plasma electron. To develop the plasma discharge device for high efficiency in the hydroxyl radical generation, proper model for estimation of plasma power is necessary. In this work, the 1-D spherical model was developed, considering temperature dependence material constants. The relation between the plasma power and hydroxyl generation was also studied by the comparison between the optical emission intensity from the hydroxyl radical using monochromator and estimated plasma power. First, the thickness of vapor layer thickness was estimated using the Navier-Stokes fluid equation in order to calculate the discharge E-field inside vapor layer. Using the E-field magnitude and power balance on the plasma generation, it was possible to estimate the plasma power. The plasma power was assumed to uniformly fill the vapor layer and the temperature of vapor layer was fixed in the boiling temperature of electrolyte, 375K. In the experiment, the aqua-plasma was discharged in the saline by applied the voltage on the bipolar electrode. The range of applied voltage was 234 to 280V-rms in the frequency of 380 kHz. Two type electrodes were produced with two ${\Phi}0.2$ tungsten. The plasma power was estimated from the V-I signal from the two high voltage probes and current probe. The estimated plasma power agreed with the profile of emission intensity when the plasma discharged between the metal electrode and vapor layer surface. However, when the plasma discharged between the metal electrodes, the increasing rate of emission intensity was lower than the increase of plasma power. It implies that the surface reaction is more sufficient rather than the volume reaction in the radical generation, due to the high density of water molecule in the liquid.

  • PDF

Unsteady Flow with Cavitation in Viscoelastic Pipes

  • Soares, Alexandre K.;Covas, Didia I.C.;Ramos, Helena M.;Reis, Luisa Fernanda R.
    • International Journal of Fluid Machinery and Systems
    • /
    • 제2권4호
    • /
    • pp.269-277
    • /
    • 2009
  • The current paper focuses on the analysis of transient cavitating flow in pressurised polyethylene pipes, which are characterized by viscoelastic rheological behaviour. A hydraulic transient solver that describes fluid transients in plastic pipes has been developed. This solver incorporates the description of dynamic effects related to the energy dissipation (unsteady friction), the rheological mechanical behaviour of the viscoelastic pipe and the cavitating pipe flow. The Discrete Vapour Cavity Model (DVCM) and the Discrete Gas Cavity Model (DGCM) have been used to describe transient cavitating flow. Such models assume that discrete air cavities are formed in fixed sections of the pipeline and consider a constant wave speed in pipe reaches between these cavities. The cavity dimension (and pressure) is allowed to grow and collapse according to the mass conservation principle. An extensive experimental programme has been carried out in an experimental set-up composed of high-density polyethylene (HDPE) pipes, assembled at Instituto Superior T$\acute{e}$cnico of Lisbon, Portugal. The experimental facility is composed of a single pipeline with a total length of 203 m and inner diameter of 44 mm. The creep function of HDPE pipes was determined by using an inverse model based on transient pressure data collected during experimental runs without cavitating flow. Transient tests were carried out by the fast closure of the ball valves located at downstream end of the pipeline for the non-cavitating flow and at upstream for the cavitating flow. Once the rheological behaviour of HDPE pipes were known, computational simulations have been run in order to describe the hydraulic behaviour of the system for the cavitating pipe flow. The calibrated transient solver is capable of accurately describing the attenuation, dispersion and shape of observed transient pressures. The effects related to the viscoelasticity of HDPE pipes and to the occurrence of vapour pressures during the transient event are discussed.

Triton WR-1339 복강주사로 유도된 생쥐의 고지혈증에 대한 참홑파래 추출물의 영향 (Effect of the Seaweed (Monostroma nitidum) Extract on Triton WR-1339 Induced Hyperlipidemia in Mouse)

  • 정영하;조용철;박인식;안상현;김진택;강용주;홍용기
    • 한국수산과학회지
    • /
    • 제30권5호
    • /
    • pp.850-858
    • /
    • 1997
  • An antihyperlipidemic effect was observed by intraperitoneal injection of the seaweed Monostroma nitidum extract. Hyperlipidemia was induced by intraperitoneal injection of Triton WR-1339 $(60\;{\mu}g/g-body\;weight)$ into a mouse. Maximum level of blood cholesterol was reached at 20 hours after Triton injection. By simultaneous injection of the M. nitidum extract $(30\;{\mu}g/g-body\;weight)$ with the Triton into each right and left sides of the peritoneal cavity, levels of total cholesterol and low density lipoprotein were decreased to $24\%\;and\;14\%$ compared to Triton injection only. For histochemical changes, hepatic tissues obtained at 40 hours after injection of the Triton and the M. nitidum extract were fixed in fromol-calcium solution. The meshlike cytoplasms disappeared and hapatic plates were recovered in mice injected with the M. nitidum extract. Numbers of lipid drops and cholesterol particles also decreased in the portal space of the hepatic cytoplasm. This indicates that the accumulation of lipid, including cholesterol, caused by Triton was prevented by the antihyperlipidemic effect of extract from the seaweed M. nitidum.

  • PDF

동축공기 수소확산 화염의 자기상사성에 대한 연구 (A Study on Self-Similarity in Turbulent Hydrogen Jet Flames with Coaxial Air)

  • 김문기;김승한;윤영빈
    • 한국항공우주학회지
    • /
    • 제30권5호
    • /
    • pp.71-78
    • /
    • 2002
  • 동축공기 수소확산 화염에서 세 가지 동축공기 조건과 화염의 유무에 따라 실험조건을 분류하고, 이에 대해 PIV를 이용하여 실험을 수행하였다. PIV를 통해 얻은 속도장을 이용하여 평균속도, 난류강도, Reynolds stress 등을 구하여 유동장을 분석하였다. 우선 단순제트에 대해 상사성을 살펴본 결과 이전의 다른 연구자의 실험결과와 일치하였다. 동축공기가 있는 경우 중심축 속도 감쇠는 $x^{-1}$에 비례하여 감소하는 것을 확인하였다. 축방향 길이를 유효밀도에 의해 정의된 유효 제트 지름으로 무차원화한 값으로 중심축 속도를 도시한 결과 하나의 선분에 떨어지는 것을 확인하였다. 평균속도 분포를 살펴보면 일정한 연료유량에 동축공기 유량을 증가시킨 경우 동축공기가 증가함에 따라 속도 분포의 형태가 바뀌게 되어 자기상사성이 유지되지 않는 것으로 보인다. 난류강도는 평균속도 분포의 경우보다 후류에서 자기상사성이 나타난다.

Numerical Analysis of the Wavelength Dependence in Low Level Laser Therapy (LLLT) Using a Finite Element Method

  • Yoon, Jin-Hee;Park, Ji-Won;Youn, Jong-In
    • The Journal of Korean Physical Therapy
    • /
    • 제22권6호
    • /
    • pp.77-83
    • /
    • 2010
  • Purpose: The aim of this study was to do numerical analysis of the wavelength dependence in low level laser therapy (LLLT) using a finite element method (FEM). Methods: Numerical analysis of heat transfer based on a Pennes' bioheat equation was performed to assess the wavelength dependence of effects of LLLT in a single layer and in multilayered tissue that consists of skin, fat and muscle. The three different wavelengths selected, 660 nm, 830 nm and 980 nm, were ones that are frequently used in clinic settings for the therapy of musculoskeletal disorders. Laser parameters were set to the power density of 35.7 W/$cm^2$, a spot diameter of 0.06 cm, and a laser exposure time of 50 seconds for all wavelengths. Results: Temperature changes in tissue based on a heat transfer equation using a finite element method were simulated and were dominantly dependent upon the absorption coefficient of each tissue layer. In the analysis of a single tissue layer, heat generation by fixed laser exposure at each wavelength had a similar pattern for increasing temperature in both skin and fat (980 nm > 660 nm > 830 nm), but in the muscle layer 660nm generated the most heat (660 nm ${\gg}$ 980 nm > 830 nm). The heat generation in multilayered tissue versus penetration depth was shown that the temperature of 660 nm wavelength was higher than those of 830 nm and 980 nm Conclusion: Numerical analysis of heat transfer versus penetration depth using a finite element method showed that the greatest amount of heat generation is seen in multilayered tissue at = 660 nm. Numerical analysis of heat transfer may help lend insight into thermal events occurring inside tissue layers during low level laser therapy.

광섬유 온도센서를 위한 InP의 광학적 특성 연구 (A study on optical properties of InP for implementation of fiber-optic temperature sensor)

  • 김영수;신건학;전병실
    • 센서학회지
    • /
    • 제3권3호
    • /
    • pp.36-44
    • /
    • 1994
  • Inp 소자를 이용하여 광섬유 온도 센서를 제작하고 InP센서의 기초 광흡수단의 이동특성을 조사하였다. 그 결과를 일반 반도체의 흡수계수에 적용하여 InP 소자의 광흡수 계수(${\Omega}$)를 유도하였다. 광흡수 계수와 InP 센서소자의 두께 파라미터를 전달특성에 대입하여 온도변화에 따른 기초 광흡수단 가장자리의 이동특성을 세점의 온도($249^{\circ}K$, $298^{\circ}K$, $369^{\circ}K$)에서 컴퓨터로 계산하고 실험 결과와 비교하였다. 그 결과 InP 소자의 기초 광흡수단이 온도에 비례하여 장파장 영역으로 이동하였으며 단위 온도 상승시 광흡수단의 이동거리는 약 0.42 nm / $^{\circ}K$ 였다. 또 반도체 소자의 두께가 증가할수록 광 파워 밀도 곡선이 낮은 온도로 이동하였다.

  • PDF

중.저준위 방사성폐기물 처분 부지 내 배경 단열의 통계적 특성 분석 (Analysis of the statistical properties for the background fractures in the LILW disposal site of Korea)

  • 지성훈;박경우;김경수;김천수
    • 방사성폐기물학회지
    • /
    • 제6권4호
    • /
    • pp.257-263
    • /
    • 2008
  • 중 저준위 방사성패기물 처분장 부지의 지하수 시스템을 개념화하기 위해 부지 내 유동성 배경 단열의 통계적 특성을 분석하였다. 이를 위해 부지 내 시추공에서 얻어진 시추공 로깅 자료의 배경 단열의 주향과 경사 자료를 분석하여 부지 내 배경 단열들을 4개의 단열군으로 분류하였다. 그리고 시추공에서의 수리 시험 결과로 얻어진 시추공 구간별 투수량계수 분포 자료로부터 배경 단열의 투수량계수 분포를 추정하였다. 각 단열군의 단열 크기 분포는 관찰된 단열 밀도와 지표지질조사 자료로부터 유추하였다. 이렇게 얻어진 배경 단열의 통계적 특성을 부지에서 관찰된 투수량계수 분포와 분석 된 통계적 특성을 이용하여 생성된 단열망 모형으로부터 계산된 투수량계수 분포를 비교하여 검증하였고, 검증 결과 관측치와 계산치가 비슷함을 확인하였다.

  • PDF