• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 1999년도 유체기계 연구개발 발표회 논문집
• /
• pp.252-256
• /
• 1999

In this research, the performance predictions of the submersible mixer were investigated. The variation of the performance characteristics by changing the impeller design parameters were discussed through the flow calculation results by using a commercial program, FLUENT. The performance of the submersible mixers is related to the velocity diffusion profiles downstream of the impeller and also the required input motor power to mix the fluid. In this study, the various design parameters such as the number of blade, the hub and tip diameters, the impeller blade profiles and revolution speed of the blades were taken for the fixed values. The blade sweep direction, the chord length distribution along with the radius of the blade and the inlet blade angle were changed to make different testing models. The flow calculation results show the effect of the changed design parameters on the performance of the submersible mixers and also give some helpful information for designing more efficient submersible mixers.

• 산업공학
• /
• 제14권2호
• /
• pp.140-147
• /
• 2001

In the turbine-blade manufacturing industry, turbine-blades are machined and then are assembled to form a circular roll of blades. The roll of blades should be balanced as much as possible, since otherwise the efficiency of the turbine generator might be damaged. A locking blade is a blade whose location is fixed and a non-locking blade is a blade whose location can be freely changed. In this paper, we study methods for balancing the weights of the rotating blades for a turbine where some blades are locking blades. The turbine-blade balancing problem is formulated into a mixed-integer programming problem, which turns out to be NP-hard. A heuristic method based on the number partitioning algorithm is developed and the computational experiments show very promising results.

• 소음진동
• /
• 제5권2호
• /
• pp.215-224
• /
• 1995

In this paper, the three-dimensional finite element model is established to investigate the structural dynamic characteristics of rotor blade using a finite element analysis. Six natural frequencies and mode shapes are calculated by computer simulation. The first three flapping modal frequencies, the first two lead-lag modal frequencies, and the first feathering modal frequency are validated through comparison with the modal test results of the fixed rotor blade. The computer simulation results are found in good agreement with experimentally measured natural frequencies. The important results are obtained as follows: (1) Natural frequencies are changed due to the variation of rotational speed and fiber angle of rotor blade, (2) Weak coupling between flapping mode shape and lead-lag mode shape are detected, (3) Centrifugal force has more effect on flapping modal frequency than lead-lag modal frequency.

• 대한치과의사협회지
• /
• 제19권11호통권150호
• /
• pp.975-979
• /
• 1981

In May 1981, the author placed Free Design Blade Implant into a 24-year old female patient with missing teeth of lower left molars, who did not want a removable partial denture. The bone available was good enough and in apparent general good health. The implant bridge was mad by four units, from 1st premolar to implant head, which is now in good esthetics and function.

• 대한기계학회논문집A
• /
• 제24권9호
• /
• pp.2259-2265
• /
• 2000

A dynamic modeling of a rotating pretwist blade which interacts with the fluid is proposed in this study. The hybrid deformation variable modeling method is employed to derive the equations of motion. The external force and moment induced by the fluid (with fixed configurations of the blade) are obtained by fluid flow analysis and tabulated in a database. This database is efficiently utilized to save the computational effort to calculate the dynamic response of the blade. The numerical results show that the fluid affects the transient response as well as frequency characteristics of the system.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.170-175
• /
• 2005

The focus of this paper is to observe the aerodynamic and vibration characteristics of the NACA0012 blade(AR=16.6) fixed on the lower surface of the wind tunnel, by changing air speed and the blade's angle of attack. After fixing a slit-typed vortex generator on the front of the blade, it could be observed that the vibrational characteristics caused by interactions between vortex and blade through the 5-hole pilot tubes. And, also, two different blades in stiffness had been prepared for observing those characteristics above in this experiment. The results were compared with the given stiffness of blade, as well. According to the results, it is clear to recognize that the vibration spectrum increases while air speed and angle of attack increase, and, also, less stiffness means bigger vibration spectrum.

• International Journal of Aeronautical and Space Sciences
• /
• 제9권2호
• /
• pp.18-33
• /
• 2008

This paper presents design optimization of a new Active Twist Rotor (ATR) blade and conducts its aeroelastic analysis in forward flight condition. In order to improve a twist actuation performance, the present ATR blade utilizes a single crystal piezoelectric fiber composite actuator and the blade cross-sectional layout is designed through an optimization procedure. The single crystal piezoelectric fiber composite actuator has excellent piezoelectric strain performance when compared with the previous piezoelectric fiber composites such as Active Fiber Composites (AFC) and Macro Fiber Composites (MFC). Further design optimization gives a cross-sectional layout that maximizes the static twist actuation while satisfying various blade design requirements. After the design optimization is completed successfully, an aeroelastic analysis of the present ATR blade in forward flight is conducted to confirm the efficiency in reducing the vibratory loads at both fixed- and rotating-systems. Numerical simulation shows that the present ATR blade utilizing single crystal piezoelectric fiber composites may reduce the vibratory loads significantly even with much lower input-voltage when compared with that used in the previous ATR blade. However, for an application of the present single crystal piezoelectric actuator to a full scaled rotor blade, several issues exist. Difficulty of manufacturing in a large size and severe brittleness in its material characteristics will need to be examined.

• 한국유체기계학회 논문집
• /
• 제3권2호
• /
• pp.31-35
• /
• 2000

In this research, the performance predictions of the submersible mixer were investigated. The variation of the performance characteristics by changing the impeller design parameters were discussed through the flow calculation results by using a commercial program, FLUENT. The performance of the submersible mixers is related to the velocity diffusion profiles downstream of the impeller and also the required input motor power to mix the fluid. In this study, the various design parameters such as the number of blade, the hub and tip diameters, the impeller blade profiles and revolution speed of the blades were taken for the fixed values. The blade sweep direction, the chord length distribution along with the radius of the blade and the inlet blade angle were changed to make different testing models. The flow calculation results show the effect of the changed design parameters on the performance of the submersible mixers and also give some helpful information for designing more efficient submersible mixers.

• Journal of Biosystems Engineering
• /
• 제28권5호
• /
• pp.421-428
• /
• 2003

This study was conducted to determine the optimum blade shape for peeling Altari radish. To figure out the required peeling force according to various angles of blade and rakes of peeling cutter, two peeling tests such as circumferential peeling and longitudinal peeling of Altari radish were carried out. Based on the pretest results, which performed to investigate the applicability of the optimum shape of cutter and to find out the cutting pattern according to the lapse of days after harvesting the radish, the peeling depth and width of the blade were fixed at 2 mm and 10 mm. From two methods of circumferential and longitudinal peeling test, the angles of rake and blade as cutter shape factors were affected on peeling force. But the peeling speed was not affected on it under the safety speed as 0.2 m/s, without blade vibrating on peeling operation. The rake angle was more effective factor than the blade angle, and the optimum angles of blade and rake were 10$^{\circ}$ and 55$^{\circ}$ respectively. The cutting surface by the longitudinal peeling was more smooth than that by the circumferential peeling. There was no problem in peeling work during 4 days after harvest because the freshness of the Altari radish was maintained.

• 항공우주시스템공학회지
• /
• 제4권2호
• /
• pp.21-25
• /
• 2010

Fatigue properties of composite materials are extremely important to design durable and reliable helicopter rotor blades. However, it is very difficult to apply conventional fatigue test loads in short period. Therefore, accelerating test speed and facilitating spectrum load realization are required. In this study, we have developed a fatigue testing method that uses a resonance of simply supported beam type blade specimen. This test consists in exciting the blade specimen with a frequency that corresponds to its natural frequency. In that case, the test specimen similar to a beam fixed between two pivot points starts vibrating and is significantly deformed. Resonant fatigue tests were performed by changing exciting vertical amplitude and frequency, and S-N curves of each composite materials were successfully obtained.