• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.7
• /
• pp.22-29
• /
• 2004

As a result of high integration of semiconductor device, the global planarization of multi-layer structures is necessary. So the chemical mechanical polishing(CMP) is widely applied to manufacturing the dielectric layer and metal line in the semiconductor device. CMP process is under influence of polisher, pad, slurry, and process itself, etc. In comparison with the general CMP which uses the slurry including abrasives, fixed abrasive pad takes advantage of planarity, resulting from decreasing pattern selectivity and defects such as dishing & erosion due to the reduction of abrasive concentration especially. This paper introduces the manufacturing technique of fixed abrasive pad using hydrophilic polymers with swelling characteristic in water and explains the self-conditioning phenomenon. And the tungsten CMP using fixed abrasive pad achieved the good conclusion in terms of the removal rate, non-uniformity, surface roughness, material selectivity, micro-scratch free contemporary with the pad life-time.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.2 no.4
• /
• pp.17-24
• /
• 2003

Chemical mechanical polishing(CMP) has been applied for planarization of topography after patterning process in semiconductor fabrication process. Tungsten CMP is necessary to build up interconnects of semiconductor device. But the tungsten dishing and the oxide erosion defects appear at end-point during tungsten CMP. It has been known that the generation of dishing and erosion is based on the over-polishing time, which is determined by pattern selectivity. Fixed abrasive pad takes advantage of decreasing the defects resulting flam reducing pattern selectivity because of the lower abrasive concentration. The manufacturing technique of fixed abrasive pad using hydrophilic polymers is introduced in this paper. For application to tungsten CMP, chemicals composed of oxidizer, catalyst, and acid were developed. In comparison of the general pad and slurry for tungsten CMP, the fixed abrasive pad and the chemicals resulted in appropriate performance in point of removal rate, uniformity, material selectivity and roughness.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1296-1301
• /
• 2003

The chemical mechanical polishing(CMP) is necessarily applied to manufacturing the dielectric layer and metal line in the semiconductor device. The conditioning of polishing pad in CMP process additionally operates for maintaining the removal rate, within wafer non-uniformity, and wafer to wafer non-uniformity. But the fixed abrasive pad(FAP) using the hydrophilic polymer with abrasive that has the swelling characteristic by water owns the self-conditioning advantage as compared with the general CMP. FAP also takes advantage of planarity, resulting from decreasing pattern selectivity and defects such as dishing due to the reduction of abrasive concentration. This paper introduces the manufacturing technique of FAP. And the tungsten CMP using FAP achieved the good conclusion in point of the removal rate, non-uniformity, surface roughness, material selectivity, micro-scratch free contemporary with the pad life-time.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.78-81
• /
• 2003

Polishing Processes are widely used in the glass, optical, die and semiconductor industry and are conventionally carried out using abrasive slurry and a polishing pad. But abrasive slurry process has a weak point that is high cost of handling of used slurry and hard controllability of slurry. Recently, some researches have attempted to solve these problems and one method is the development of a fixed abrasive pad. FAP has a couple of advantages including clean environment, lower CoC, easy controllability and higher form accuracy. But FAP also has a weak point that is need of dressing because of glazing and loading. The paper introduces the basic concept and fabrication technique of FAP using hydrophilic polymers with swelling characteristics in water and explains the self-conditioning phenomenon. Experimental results demonstrate to achieve nano surface roughness of soda lime glass for optical application

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.206-209
• /
• 2002

The fixed abrasive pad(FAP) has been introduced in chemical mechanical polishing(CMP) field recently. In comparison with the general CMP which uses the slurry including abrasives, FAP takes advantage of planarity. resulting from decreasing pattern selectivity and defects such as dishing due to the reduction of abrasive concentration especially. This paper introduces the manufacturing technique of $Al_2$O$_3$-FAP using hydrophilic polymers with swelling characteristic in water and explains the self.texturing phenomenon. It also focuses on the chemical effects on tungsten film and the FAP is evaluated on the removal rate as a function of chemicals such as oxidizer, catalyst, and acid. The removal rate is achieved up to 1000A1min as about 70 percents of the general one. In the future. the research has a plan of the advanced FAP and chemicals in tungsten CMP considering micro-scratch, life-time, and within wafer non-uniformity.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.10
• /
• pp.212-220
• /
• 2002

The finishing process for die and mold manufacturing is very important because it influences the final quality of products. Injection molds need higher quality surface than general purpose dies and molds. Conventional polishing can not make mold surface down to nanometer roughness efficiently because of their loading and glazing. This paper focused on the development of fixed abrasive pad using water swelling mechanism of polymer binder network. Self-conditioning was recognized as the long term polishing stabilization tool without any loading or glazing because water makes fixed abrasives free by swelling of the pad. Consequently, stable nano-polishing process has been applied on the injection mold, from the experimental results with polished surface roughness of Ra 15.1nm on STD-11 die steel.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.4
• /
• pp.321-326
• /
• 2005

Chemical mechanical polishing(CMP) process is essential technology to be applied to manufacturing the dielectric layer and metal line in semiconductor devices. It has been known that overpolishing in CMP depends on pattern selectivity as a function of density and pitch, and use of fixed abrasive pad(FAP) is one method which can improve the pattern selectivity. Thus, dishing & erosion defects can be reduced. This paper introduces the manufacturing technique of FAP using hydrophilic polymers with swelling characteristic in water and explains the self-conditioning phenomenon. When applied to tungsten blanket wafers, the FAP resulted in appropriate performance in point of uniformity, material selectivity and roughness. Especially, reduced dishing and erosion was observed in CMP of tungsten pattern wafer with the proposed FAP.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.140-143
• /
• 2004

Chemical mechanical polishing(CMP) is essential technology to secure the depth of focus through the global planarization of wafer. But a variety of defects such as contamination, scratch, dishing, erosion and corrosion are occurred during CMP. Especially, dishing and erosion defects increase the resistance because they decrease the interconnect section area, and ultimately reduce the life time of the semiconductor. Due to this dishing and erosion must be prohibited. The pattern density and size in chip have a significant influence on dishing and erosion occurred over-polishing. Decreasing of abrasive concentration results in advanced pattern selectivity which can lead the uniform removal in chip and decrease of over-polishing. The fixed abrasive pad was applied and tested to reduce dishing and erosion in this paper. Consequently, reduced dishing and erosion was observed in CMP of tungsten pattern wafer with proposed fixed abrasive pad and chemicals.

• Tribology and Lubricants
• /
• v.34 no.6
• /
• pp.279-283
• /
• 2018

In this study, we investigate the behavior of abrasive particles and change of the stick-slip pattern according to chemical mechanical polishing (CMP) process parameters when a large number of abrasive particles are fixed on a pad. The CMP process is simulated using the finite element method. In the simulation, the abrasive grains are composed of those used in the actual CMP process. Considering the cohesion of the abrasive grains with the start of the CMP process, abrasive particles with various sizes are fixed onto the pad at different intervals so that stick-slip could occur. In this analysis, we determine that when the abrasive particle size is relatively large, the stick-slip period does not change as the pressure increases while the moving speed is constant. However, if the size of the abrasive grains is relatively small, the amount of deformation of the grains increases due to the elasticity of the pad. Therefore, the stick-slip pattern may not be observed. As the number of abrasive particles increases, the stick-slip period and displacement decrease. This is consistent with the decrease in the von Mises yield stress value on the surface of the wafer as the number of abrasive grains increases. We determine that when the number of the abrasive grains increases, the polishing rate, and characteristics are improved, and scratches are reduced. Moreover, we establish that the period of stick-slip increases and the change of the stick-slip size was not large when the abrasive particle size was relatively small.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.2
• /
• pp.38-45
• /
• 2005

Chemical mechanical polishing(CMP) has been widely accepted for the planarization of multi-layer structures in semiconductor fabrication. But a variety of defects such as abrasive contamination, scratch, dishing, erosion and corrosion are occurred during CMP. Especially, dishing and erosion defects increase the metal resistance because they decrease the interconnect section area, and ultimately reduce the lift time of the semiconductor. Due to this reason dishing and erosion must be prohibited. The pattern density and size in chip have a significant influence on dishing and erosion occurred by over-polishing. The fixed abrasive pad(FAP) was applied and tested to reduce dishing and erosion in this paper. The abrasive concentration decrease of FAP results in advanced pattern selectivity which can lead the uniform removal in chip and declining over-polishing. Consequently, reduced dishing and erosion was observed in CMP of tungsten pattern wafer with proposed FAP and chemicals.