• Proceedings of the KIEE Conference
• /
• 2004.11a
• /
• pp.215-219
• /
• 2004

Metal-chelate derivatives have been investigated intensively as an emitting layer and recognize to have excellent electroluminescence(EL) properties. We synthesized new luminescent material, 1,4-dihydoxy-5,8-naphtaquinone $Aiq_3$ complex($Al_2Nq_4$) and investigated the electrical optical properties. OLED has potential candidates for information display with merits of thickness, low power and high efficiency. Although the OLED show a lot of advantages for information display, it has the limit of inorganic(metal)/ organic interface. In this study, the two methods are used to study the interface of metal/organic in OLED. First, we treated $O_2$ plasma on an ITO thin film by using RIE system, and analyzed the ingredient of ITO thin film according to change of the processing conditions. We used the RDS and the XPS for the ingredient analysis of the surface and bulk. We measured electrical resistivity using Four-Point-Probe and calculated sheet resistance, and ITO surface roughness was measured by using AFM. We fabricated OLED using substrate that was treated optimum ITO surface. Second, we used the buffer layer of CuPc to improve the characteristics of the interface and the hole injection in OLED. The result of the study for electrical and optical properties by using I V L T System(Flat Panel Display Analysis System), we confirmed that the electrical properties and the luminance properties were improved.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.13 no.5
• /
• pp.38-50
• /
• 2010

Expressways are often upgraded by widening the lanes and/or by reshaping the roads to be more linear for faster travel time. However, during the process of improving the route of the expressways, the areas where the old expressways used to be are often unused and abandoned. When these neglected sites are left alone, they often become dump sites causing pollution and impacting the surrounding environment. Therefore, it is important to restore the abandoned expressway sites to its full natural beauty. In this study, the abandoned expressway at the Soksa interchange in Pyungchang county, located in Kangwon province was studied for establishing the model of ecological restoration project. Considering the characteristics of the site, the target flora species was chosen to be Quercus species and the target fauna species as amphibians. After the target species were carefully chosen, each species' habitat requirements were studied in order to figure out the appropriate methods toward habitat restoration specifically for these species. In addition, to determine the most efficient method toward restoration of abandoned expressways, the study utilized the planting hole techniques, the crack techniques, and the colonization techniques. In terms of the spatial organization, public education program is incorporated at the main entrance area and the programs for experimenting, and developing vegetation and habitat restoration techniques are placed in the vicinity. In the master plan-to provide natural ecosystem at the site-ASCON (asphalt concrete) was removed first, then plans for restoration including species' habitat restoration were established. Furthermore, the project included plans for improving water quality polluted through non-point source considering the surrounding nearby road and farm lands. Finally, the study established a planning process that will experimentally apply to the abandoned expressway restoration method. In the future, there will be a continuous monitoring of the methods applied to verify if the restoration methods are effective. Also, new restoration techniques should be available according to a variety of abandoned expressways' characteristics.

• Journal of Korean Medical classics
• /
• v.21 no.1
• /
• pp.27-42
• /
• 2008

It is generally called that the Donhwang Manuscript[敦煌本] "Sanghallon(傷寒論)" is all the series of documents relating to the "Sanghallon(傷寒論)", included in one of the testaments, which was, in 1900, originally found in the Janggyeong hole[藏經洞], Makgo cave[莫高庸], Donhwang(敦煌), Gamsuk province[甘肅省]. The consecutive numbers of the Manuscript are S 202 and P 3287, the former is called the "Sanghallon(傷寒論)" A-Manuscript[甲本] and the latter consists of the "Sanghallon(傷寒論)" B-Manuscript[乙本] and the "Sanghallon(傷寒論)" C-Manuscript[丙本]. The Donhwang Manuscript is a type of a hurt book, but not a complete form of a book. As the research conducted, it has been proven that the Donhwang Manuscript "Sanghallon(傷寒論)" has the academic values as mentioned below. First, it is highly valuable to inter-related study and revise the "Sanghallon(傷寒論)". Second, it is one of circumstantial evidences to have various kinds of versions of the "Sanghallon(傷寒論)". Third, its findings somehow wipes out arguments concerning with identifying authors of the "Sanghallon(傷寒論) Sanghanrye(傷寒例)" and the "Sanghallon(傷寒論) Byeonmaekbeop(辦脈法)". Fourth, it has turned out that the existing "Geumgweokhamgyeong" is not a forgery, but one of imparted versions of the "Sanghallon(傷寒論)" In conclusion, it could be acknowledged that the discovery of the Donhwang Manuscript "Sanghallon(傷寒論)" enables to arrange and revise the "Sanghallon(傷寒論)", and it has provided researchers with critical evidences about ascertaining many kinds of different versions of the "Sanghallon(傷寒論)". Moreover, we can also find the great contribution of this findings which could clarify various non-proven arguments within many experts and researchers.

• Journal of KIISE:Software and Applications
• /
• v.32 no.7
• /
• pp.625-635
• /
• 2005

In this paper, we propose a hybrid approach for segmenting the lungs efficiently and automatically in chest CT images. The proposed method consists of the following three steps. first, lungs and airways are extracted by two- and three-dimensional automatic seeded region growing and connected component labeling in low-resolution. Second, trachea and large airways are delineated from the lungs by two-dimensional morphological operations, and the left and right lungs are identified by connected component labeling in low-resolution. Third, smooth and accurate lung region borders are obtained by refinement based on image subtraction. In experiments, we evaluate our method in aspects of accuracy and efficiency using 10 chest CT images obtained from 5 patients. To evaluate the accuracy, we Present results comparing our automatic method to manually traced borders from radiologists. Experimental results show that proposed method which use connected component labeling in low-resolution reduce processing time by 31.4 seconds and maximum memory usage by 196.75 MB on average. Our method extracts lung surfaces efficiently and automatically without additional processing like hole-filling.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.3
• /
• pp.608-618
• /
• 2007

Image binarization is an important preprocessing to identify the object of interest by dividing pixels into the background and object. We proposes efficient binarization method and a stroke reconstruction method of the low quality character image for an effective character recognition. First, the character image is binarized by using the both advantages of local and global thresholding method and then the noise elimination around the character stroke and the hole filling on the stoke by the analysis of the binarized stroke image are performed to enhance the quality of the character stroke. Proposed binarization algorithm for character image achieved an efficiency of both processing speed and performance by the adaptive threshold selection. Moreover, We could get a high qualify binary image by a stroke reconstruction of the step-by-step denoising process.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.63-64
• /
• 2012

A pyrotechnic actuated device (PAD) is a component that delivers high power in remote environments by combustion of a self-contained energy source. Historically, the design of these devices has been largely empirical and considered to be an art. In this study, an overview for developing an analytical model is introduced that efficiently evaluates performance of PAD. The model is integrated by three parts of different disciplines that are coupled in sequence with each other. First is the solid explosive burning to form product gas within an actuator and transport to an expansion chamber. Second is the insertion of initially tapered piston into a small hole by gas pressure in the chamber. Third is the shear cutting of the diaphragm from the piston to enable gas flow into the conduit. Some results of preliminary study for each of three parts are introduced in the presentation.

• Smart Structures and Systems
• /
• v.2 no.2
• /
• pp.115-126
• /
• 2006

The Terra-Scope system is an affordable 4-D down-hole seismic monitoring system based on independent, microprocessor-controlled sensor Pods. The Pods are nominally 50 mm in diameter, and about 120 mm long. They are expected to cost approximately $6000 each. An internal 16-bit, extremely low power MCU controls all aspects of instrumentation, eight programmable gain amplifiers, and local signal storage. Each Pod measures 3-D acceleration, tilt, azimuth, temperature, and other parametric variables such as pore water pressure and pH. Each Pod communicates over a standard digital bus (RS-485) through a completely web-based GUI interface, and has a power consumption of less than 400 mW. Three-dimensional acceleration is measured by pure digital force-balance MEMS-based accelerometers. These accelerometers have a dynamic range of more than 115 dB and a frequency response from DC to 1000 Hz with a noise floor of less than $30ng_{rms}/{\surd}Hz$. Accelerations above 0.2 g are measured by a second set of MEMS-based accelerometers, giving a full 160 dB dynamic range. This paper describes the system design and the cooperative shared-time scheduler implemented for this project. Restraints accounted for include multiple data streams, integration of multiple free agents, interaction with the asynchronous world, and hardened time stamping of accelerometer data. The prototype of the device is currently undergoing evaluation. The first array will be installed in the spring of 2006.

• Journal of Gastric Cancer
• /
• v.21 no.2
• /
• pp.132-141
• /
• 2021

Purpose: Intracorporeal esophagojejunostomy during reduced-port gastrectomy for proximal gastric cancer is a technically challenging technique. No study has yet reported a robotic technique for anastomosis. Therefore, to address this gap, we describe our reduced-port technique and the short-term outcomes of intracorporeal esophagojejunostomy. Materials and Methods: We conducted a retrospective review of patients who underwent a totally robotic reduced-port total or proximal gastrectomy between August 2016 and March 2020. We used an infra-umbilical Single-Site^® port with two additional ports on both sides of the abdomen. To transect the esophagus, a 45-mm endolinear stapler was inserted via the right abdominal port. The common channel of the esophagojejunostomy was created between the apertures in the esophagus and proximal jejunum using a 45-mm linear stapler. The entry hole was closed with a 45-mm linear stapler or robot-sewn continuous suture. All anastomoses were performed without the aid of an assistant or placement of stay sutures. Results: Among the 40 patients, there were no conversions to open, laparoscopic, or conventional 5-port robotic surgery. The median operation time and blood loss were 254 min and 50 mL, respectively. The median number of retrieved lymph nodes was 40.5. The median time to first flatus, soft diet intake, and length of hospital stay were 3, 5, and 7 days, respectively. Three (7.5%) major complications, including two anastomosis-related complications and a case of small bowel obstruction, were treated with an endoscopic procedure and re-operation, respectively. No mortality occurred during the study period. Conclusions: Intracorporeal esophagojejunostomy during reduced-port gastrectomy can be safely performed and is feasible with acceptable surgical outcomes.

• Advances in concrete construction
• /
• v.14 no.5
• /
• pp.317-330
• /
• 2022

This paper investigated computationally and experimentally the interaction here between a notch as well as a micropore under uniaxial compression. Brazilian tensile strength, uniaxial tensile strength, as well as biaxial tensile strength are used to calibrate PFC2d at first. Then, uniaxial compression test was conducted which they included internal notch and micro pore. Experimental and numerical building of 9 models including notch and micro pore were conducted. Model dimensions of models are 10 cm × 10 cm × 5 cm. Joint length was 2 cm. Joints angles were 30°, 45° and 60°. The position of micro pore for all joint angles was 2cm upper than top of the joint, 2 cm upper than middle of joint and 2 cm upper than the joint lower tip, discreetly. The numerical model's dimensions were 5.4 cm × 10.8 cm. The fractures were 2 cm in length and had angularities of 30, 45, and 60 degrees. The pore had a diameter of 1 cm and was located at the top of the notch, 2 cm above the top, 2 cm above the middle, and 2 cm above the bottom tip of the joint. The uniaxial compression strength of the model material was 10 MPa. The local damping ratio was 0.7. At 0.016 mm per second, it loaded. The results show that failure pattern affects uniaxial compressive strength whereas notch orientation and pore condition impact failure pattern. From the notch tips, a two-wing fracture spreads almost parallel to the usual load until it unites with the sample edge. Additionally, two wing fractures start at the hole. Both of these cracks join the sample edge and one of them joins the notch. The number of wing cracks increased as the joint angle rose. There aren't many AE effects in the early phases of loading, but they quickly build up until the applied stress reaches its maximum. Each stress decrease was also followed by several AE effects. By raising the joint angularities from 30° to 60°, uniaxial strength was reduced. The failure strengths in both the numerical simulation and the actual test are quite similar.

• Restorative Dentistry and Endodontics
• /
• v.32 no.2
• /
• pp.111-120
• /
• 2007

The purpose of this study is to evaluate the effects of surface treatment and composition of reinforcement material on fracture strength of fiber reinforced composite inlay bridges. The materials used for this study were I-beam, U-beam TESCERA ATL system and ONE STEP(Bisco, IL, USA). Two kinds of surface treatments were used; the silane and the sandblast. The specimens were divided into 11 groups through the composition of reinforcing materials and the surface treatments. On the dentiform, supposing the missing of Maxillary second pre-molar and indirect composite inlay bridge cavities on adjacent first pre-molar disto-occlusal cavity, first molar mesio-occlusal cavity was prepared with conventional high-speed inlay bur. The reinforcing materials were placed on the proximal box space and build up the composite inlay bridge consequently. After the curing, specimen was set on the testing die with ZPC. Flexural force was applied with universal testing machine (EZ-tester; Shimadzu, Japan). at a cross-head speed of 1 mm/min until initial crack occurred. The data was analyzed using one-way ANOVA/Scheffes post-hoc test at 95% significance level. Groups using I-beam showed the highest fracture strengths (p<0.05) and there were no significant differences between each surface treatment (p>0.05) Most of the specimens in groups that used reinforcing material showed delamination. 1. The use of I-beam represented highest fracture strengths (p<0.05) 2. In groups only using silane as a surface treatment showed highest fracture strength, but there were no significant differences between other surface treatments (p>0.05). 3. The reinforcing materials affect the fracture strength and pattern of composites inlay bridge. 4 The holes at the U-beam did not increase the fracture strength of composites inlay bridge.