• The Journal of Advanced Prosthodontics
• /
• v.12 no.4
• /
• pp.197-203
• /
• 2020

PURPOSE. The aim of this study was to evaluate the effect of multiple firings on the bond strength between yttriatetragonal zirconia polycrystals (Y-TZP) and 2 types of resin cements. MATERIALS AND METHODS. Sixty 3Y-TZP specimens (LAVA Frame Multi) were divided into 3 groups depending on the following firing procedures: (1) 2-firing cycles, (2) 5-firing cycles, (3) 10-firing cycles. Two samples from each group were investigated by using SEM to determine the morphological changes. All specimens were treated with 125 ㎛ airborne-particle abrasion and the surface roughness of each specimen was measured. The specimens from each firing group were then further divided into 2 subgroups (n = 9) to apply 2 types of resin cement (MDP-free resin cement: RelyX Unicem-RU, and MDP containing resin cement: Panavia F 2.0-PA). The shear bond strength (SBS) test was performed and failure types of all the debonded specimens were classified by using a stereomicroscope as adhesive, cohesive, and mixed. The statistical analysis of surface roughness and SBS data were performed by using 1-way ANOVA and 2-way ANOVA followed by Tukey-HSD tests (α=.05). Failure modes were calculated as a percentage for each group. RESULTS. The bond strength of RU and PA to the specimens obtained with 2 firings were not statistically different from each other (P=.1). However, the SBS values of PA were found to be significantly higher than RU for the specimens obtained with 5 and 10 firing cycles (P=.001 and P=.02, respectively). Surface roughness analysis revealed no statistical difference between groups (P=.2). The SEM analysis of samples fired 5- and 10- times showed irregularities and boundary loss in zirconia grains, and empty spaces between zirconia grains. CONCLUSION. The bond strength of PA cement was higher than that of RU to the zirconia subjected to repeated firings (5 and 10 firing cycles). When zirconia is subjected to multiple firings, using MDP-containing resin cement can be recommended.

• The Journal of Korean Academy of Prosthodontics
• /
• v.19 no.1
• /
• pp.61-73
• /
• 1981

The effects of the opaque porcelain firing temperature, the bonding agent and the degassing prior to the opaque firing On the bond strength were investigated by means of the tensile shear stIe$. The diffusional behaviours at the interface of the porcelain and the alloy, and .the microstructures of the ceramic and metal composite were studied for understanding the bonding mechanism. The results obtained in this experiment were summarizd as follow; 1. With no application of bonding agent, the tensile shear strength of the specimen firing at $1840^{\circ}F$ was higher than that of the specimen firing at $1760^{\circ}F$. 2. The highest bond strength was obtained by application of bonding agent without degassing prior to the opaque firing. 3. Application of bonding agent after the degassing showed the lowest bond strength. 4. The greater number of pores were observed at the firing temperature of $1840^{\circ}F$ than that of $1760^{\circ}F$ in the porcelain and the interface respectively.

• Tunnel and Underground Space
• /
• v.27 no.5
• /
• pp.312-323
• /
• 2017

In this study, an influence of mixing ratio among firing oyster shell, non-firing oyster shell, magnetic separated converter steel slag and fly ash used as admixtures on strength properties of soil cement was evaluated by correlation analysis among compressive strength, deformation modulus and mixing ratio of admixtures. As a result, the strength of the specimens containing non-firing oyster shells was found to be larger than that of firing oyster shells, and it was confirmed that firing oyster shells could negatively affect the strength of soil cement specimens unlike previous studies. In addtion, there was a positive correlation between the ratio of magnetic separated converter slag and strength properties, so it is confirmed that it can be used as an admixture.

• Journal of Technologic Dentistry
• /
• v.35 no.4
• /
• pp.353-358
• /
• 2013

Purpose: This study was observation shear bonding strength by compositional change and firing step of a Ni-Cr alloy for porcelain fused metal crown. The aim of study was to suggest the material for firing step of Ni71-Cr14 alloy to development of alloy for porcelain fused to metal crown. Methods: The test was on the two kinds of Ni-Cr alloy specimens. The surfaces of two alloys were analyzed by EDX in order to observe oxide characteristic. And the shear test was performed by MTS. Results: The surface property and oxide characteristic analysis of oxide layer, weight percentage of Element O within $Ni_{71}Cr_{14}$ alloy measured 23.32wt%, and $Ni_{59}Cr_{24}$ alloy was measured 23.03wt%. And the maximum shear bonding strength was measured 58.02MPa between $Ni_{59}Cr_{24}$ alloy and vintage halo(H4 group). Conclusion: The surface property and oxide characteristic three kind of Ni-Cr alloy was similar. and shear bonding strength showed the highest bonding strength in H4 specimens.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.11a
• /
• pp.265-266
• /
• 2012

The purpose of this study was to investigate the compressive strength property into mortar using rice straw ash. In an effort to evaluate the effects of rice straw ash firing temperatures on compressive strength properties of mortar, a change in the components of rice straw ash was observed according to firing temperatures, and compressive strength of mortar and X.R.F was measured. As a results, As the mortar with a mixture ratio of rice straw ash up to 15% was found to have a compressive strength superior to that of plain mortar.

• Journal of the Korean Ceramic Society
• /
• v.31 no.4
• /
• pp.381-388
• /
• 1994

A new process which co-fires the low-firing-substrate and copper conductor was studied to achieve good bond strength and low sheet resistance of conductor. Cupric oxide is used as the precursor of conductive material in the new method and the firing atmosphere of the new process is changed sequently in air H2N2. The addition of cupric oxide and variations of firing atmosphere permited complete binder-burnout in comparison with the conventional method and contributed to the improvement of resistance and bonding behaviors. The potimum conditions of this experiment to obtain the satisfactory resistance and bond strength are as follows (binder-burnout temperature in air; 55$0^{\circ}C$, reducing temperature in H2; 40$0^{\circ}C$ for 30 min, ratio of copper and cupric oxide; 60:40~30:70 wt%). The bonding mechanism between the substrate and metal was explained by metal diffusion layer in the interface and the bond strength mainly depended on the stress caused by the difference of shrinkage and thermal expansion coefficient between the substrate and metal.

• Journal of the Korean Ceramic Society
• /
• v.32 no.8
• /
• pp.893-900
• /
• 1995

The porous wollastonite ceramics were fabricated after firing calcium silicates, obtained using natural resources and by-products of power plants by hydrothermal synthesis, without organic fibers or asbestos for reinforcement agent. A specimen from diatomite as a SiO2 staring raw material had the highest strength owing to normal grain growth and good densification from homogeneous sperhcial C-S-H hydrates. A specimen from SiO2 sol as a SiO2 starting raw material showed tobermolite, but fly ash and mixed system did xonotlite after hydrothermal synthesis. The specimen from fly ash showed the lowest firing shirikage and strength changes in the firing range from 50$0^{\circ}C$ to 120$0^{\circ}C$. The other phases in all specimens changed to wollastonite phase after firing at 100$0^{\circ}C$. Also the average pore size was distributed from 0.2${\mu}{\textrm}{m}$ to 2${\mu}{\textrm}{m}$.

• Journal of Technologic Dentistry
• /
• v.36 no.1
• /
• pp.9-15
• /
• 2014

Purpose: Generally dental technicians clinically decide the sintering temperature of zirconia artificial teeth to match the color of the teeth. However, the sintering temperature influence the microstructure and mechanical strength of ceramic body. In this study, to evaluate the free choice of sintering temperature which leads to color the problems in zirconia false teeth, the variation of microstructure, mechanical strength, and colortone of zirconia ceramics according to the change of sintering temperature was investigated. Methods: Bar type specimens were prepared from commercial zirconia blocks by cutting and polishing into $0.8cm(L){\times}1.0cm(W){\times}4.8cm(H)$. Specimens were fired from 1,400 to $1,700^{\circ}C$ at $50^{\circ}C$ intervals and held for 1hour at highest temperature. Apparent porosity, water absorption, firing shrinkage, bulk density, bend strength, whiteness were tested. Microstructures were observed by SEM. Results: When fired above $1450^{\circ}C$, all specimens showed 0% apparent porosity and water absorption, 20% firing shrinkage, and $6.1g/cm^3$ bulk density regardless of firing temperatures. SEM photomicrographs showed grain growth of zirconia occurred above $1,600^{\circ}C$. Whiteness was also largely changed above this temperature. Maximum bend strength of 1,05MPa was obtained at $1,550^{\circ}C$. Bend strength lowered slightly above this temperature and showed $950{\ss}\acute{A}$ at $1,700^{\circ}C$. Conclusion: In order to fit the colortone of zirconia artificial teeth, arbitrary choice of firing temperature higher than $1,500^{\circ}C$, up to $1,700^{\circ}C$ did not influence the mechanical strength.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.05a
• /
• pp.109-110
• /
• 2013

The purpose of this study was to investigate pozzolanic activity according to the firing temperature of the rice straw ash. In order to measure amount of SiO2 of rice straw ash, XRF(X-ray fluorescence) analysis was tested. Also to evaluate properties of mortars using rice straw ash, mortar flow, cement setting time, compressive strength was tested. As a results, as the mortar with a mixture ratio of rice straw ash up to 15% was found to have a compressive strength superior to that of plain mortar.

• Journal of the Korean Ceramic Society
• /
• v.32 no.5
• /
• pp.601-607
• /
• 1995

The bond strength between the low-firing-substrate and Cu conductor depended on the softening point and the amount of frit added to the metal paste. The addition of 3 wt% frit (softening point: 68$0^{\circ}C$) to the metal paste resulted in the improvement of bond strength, which was approximately 3 times higher (3kg/$\textrm{mm}^2$) than that of non frit condition. It was also found that fracture surface shifted to the ceramic substrate in the interface region. These phenomena were attributed to the frit migration into the metal-ceramic interface. It was thought that the migration of glass frit occurred extensively when the softening point of glass firt was 68$0^{\circ}C$. The sheet resistance of Cu conductor remained constant by the addition of 4 wt% frit regardless of softening point of frit. For all samples with more than 4 wt% frit, the sheet resistance increased abruptly.