• 한국연소학회지
• /
• 제21권4호
• /
• pp.30-38
• /
• 2016

Flame structure of co-firing coal and palm kernel shell (PKS) was investigated in a pulverized coal swirl burner by particle image velocimetry (PIV). The pulverized coal swirl flame is operated with a PKS blending ratio of 10%, 20%, and 30%. For all operating conditions, flame structures such as internal recirculation zone (IRZ), outer recirculation zone (ORZ), and exhaust tube vortex (ETV) were observed. In the center of flame, the strong velocity gradient is occurred at the stagnation point where the volatile gas combustion actively takes place and the acceleration is increased with higher PKS blending ratio. OH radical shows the burned gas region at the stagnation point and shear layer between IRZ and ORZ. In addition, OH radical intensity increases for a co-firing condition because of high volatile matter from PKS. Because the volatile gas combustion takes place at lower temperature, co-firing condition (more than 20%) leads to oxygen deficiency and reduces the combustibility of coal particle near the burner. Therefore, increasing PKS blending ratio leads to higher OH radical intensity and lower temperature.

• 한국결정성장학회지
• /
• 제29권6호
• /
• pp.270-275
• /
• 2019

마이카 커패시터는 세라믹 커패시터에 비해 내고충격 특성이 우수하여 다양한 유도무기체계의 고전압 기폭장치에 적용된다. 본 연구에서는 국산화된 마이카 고전압 커패시터의 고전압 기폭장치 적용을 위해 단자강도시험, 내습성시험, 열충격시험과 같은 환경시험과 함께 가속 수명 시험을 진행하였다. 마이카 고전압 커패시터의 고장모드는 절연저항 감소 및 이를 통한 절연 파괴이다. 가속수명모델의 중요 상수를 실험적으로 도출하였으며 전압계수 n 및 활성화 에너지 E_a는 각각 5.28 및 0.805 eV이었다. 가속모델식을 이용하여 도출한 가속계수는 496이었으며 가속수명시험을 통해 도출된 정상 사용 조건에서의 마이카 고전압 커패시터의 수명은 38.5년으로 기폭장치 적용에 문제가 없는 것으로 확인되었다.

• 한국소음진동공학회논문집
• /
• 제16권4호
• /
• pp.319-328
• /
• 2006

4-실린더 엔진의 작동 시 크랭크샤프트의 기계적 거동을 해석하는 방법에 관한 연구 논문이다 이 해석의 목적은 모드 해석을 단순화 하기위해 Pin 과 Arm을 일정하게 가정하고, 이를 통해 단순화된 크랭크샤프트의 특성을 연구하는 것이며, 해석을 통하여 얻어진 전달 함수에서의 고유진동수와 모드 형상을 실험을 통한 모드 해석과 비교하였다. 시뮬레이션을 통한 결과와 실험을 비교한 결과 해석치와 실험치의 값이 일치함을 확인할 수 있었고 이를 통하여 해석 모델을 검증하였다. 또한 검증된 모델을 통하여 엔진 작동 시 크랭크샤프트의 특성을 해석하고자 하였다. 초기 연소 조건에 기초하여 주파수 영역에서 크랭크샤프트의 동적 거동을 해석하기 위한 새로운 방법을 기술하였다. 새로운 기법은 엔진의 작동 조건에서 저널 베어링과 밸런서의 형상 변경을 통하여 얻어진 에너지 값을 계산하기 위해서 RMS값을 이용하였다.

• 한국세라믹학회지
• /
• 제44권10호
• /
• pp.548-553
• /
• 2007

Ceramic green sheets consisting Bi-based glass frit were fabricated for an application to PDP transparent dielectric front panel. The dispersion condition of the slurry for tape casting was pre-examined, and two kinds of hinder and plasticizer were used in the non-aqueous slurry system. In the fabrication process for the frit film, the properties such as dry and firing shrinkage, elongation, and transmittance were examined at the condition of various mixing ratio of plasticizers. In the mixing ratio of polyethylene glycol to dibutyl phthalate of 3:5wt%, a good adhesion, elongation and transmittance were observed at the firing temperature of $580^{\circ}C$. The photograph for the cross section of the interface was also showed a dense microstructure.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집B
• /
• pp.686-691
• /
• 2000

The flat flame made by swirling air has lots of the different characteristics according to the swirl numbers in the burner throat. Its combustion characteristics are also affected by them. In this study, the flow patterns in the flat flame burner which is no firing condition were investigated experimentally with using smoke in terms of each swirl number. Also the blow off, flame structure, temperature distribution and NO emission in the firing condition were measured at the atmosphere and combustion furnace.

• 한국컴퓨터산업학회논문지
• /
• 제10권5호
• /
• pp.193-200
• /
• 2009

본 논문에서는 IEEE 802.15.4 무선통신 표준으로 개발된 ZigBee 모듈과 다중센서를 이용하여 방범 방재 상황을 무선으로 Display하는 시스템을 구현하였다. 방범 시스템은 초음파, 적외선 센서를 이용하여 감지 시스템을 구현하였고, 메인칩으로는 PIC16F73을 사용하였다. 전등을 연결, 자동 전등 ON/OFF를 구현하였다. 방재 시스템은 온도센서를 이용하여 구현하였다. ATmega64를 사용한 무선통신모듈인 ZigBee 시스템과 다중센서를 연동하여 방범, 방재 시스템을 구현하여 감지된 데이터를 EndDevice에서 Coordinator로 전송하여 Coordinator에서 전송 받은 데이터를 PC에 Display 할 수 있도록 구현하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 C
• /
• pp.1644-1648
• /
• 2002

The relationships between MgO deposition conditions and firing voltage of AC PDP were investigated as a function of ambient temperature. Substrate temperature and growth rate were selected as the major parameters that can affect the properties of MgO most significantly. Firing voltages increase with increasing temperature regardless of deposition conditions of the MgO layer. However, the relative magnitude of the firing voltage variation decrease with increasing substrate temperature and decreasing deposition speed. It was also found that the sample obtained at the condition of lower deposition rate shows better dynamic margin characteristics.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 제5회 영호남 학술대회 논문집
• /
• pp.126-129
• /
• 2003

The electrical properties of a ZnO-based multilayered chip varistor (abbreviated as MLV) were studied as functions of firing condition and the degree of lamination. The fundamental varistor characteristics such as nonlinear coefficient and breakdown voltage were independent of the degree of lamination. As the number of the laminated ceramic sheets increased, however, not only the energy handling capability but also the capacitance and the leakage current which are relevant to delayed response to the voltage surge and the pre-breakdown energy loss, respectively, increased. With the increase of firing temperature between $950^{\circ}C$ and $1150^{\circ}C$, both the capacitance and the leakage current of the MLV increased due mainly to the grain growth of ZnO and the volatilization of $BiO_2O_3$. High performance MLVs with clear electrode pattern were obtained at the firing temperature range of $l000{\sim}1050^{\circ}C$ in this experiment.

• 한국세라믹학회지
• /
• 제17권2호
• /
• pp.69-74
• /
• 1980

This study deals with the wire content, wire diameter, aspect ratio , it's arrangement of steel, wire fiber and the sorts of castable which affected the character of steel wire fiber reinformced refractory castable. Two kinds of alumina based refractory castables, one is for 1650℃ and the other is for 1800℃, and stainless steel which is SUS 304 type 0.25, 0.34 , 0.37 and 0.50m/min diameter were used respectively. Aspect ratio was adjusted to 50, 75, 100 and steel fiber content was also adjusted to 1-4wt% each. The results of the experiment were as follows : 1. At firing temperature around 1,000℃, MOR is increased with increasing wire content and aspect ratio with decreasing firing temperature, which depends on the Romualdi's Fiber Spacing Theory. But for calculation of the fiber spacing, Swamy equation is more a aplicable to the extensive fiber mixing conditions. However, the condition differs from the above at firing temperature around 1,350℃ ,because of the degradation of wire and the progress of sintering of castable. 2. Linear change is getting larger corresponding to the increase of wire content, and the spaling resistivity is increasing corresponding to the increase of wire content and to aspect ratio, and with decreasing wire diameter. 3. Firing shrinkage under load is getting greater as higher wire content, and the shrinkage of the test pieces which fiber is vertically oriented is getting greater than the test pieces which fiber is randomly oriented.

• 한국전기전자재료학회논문지
• /
• 제22권9호
• /
• pp.776-780
• /
• 2009

In this study, the opto-electric properties of EL devices with PMN dielectric layer with variation of firing tempereature were investigated. For the PMN dielectric layer process, the paste was prepared by optimization of quantitative mixing of PMN powder, $BaTiO_3$, Glass Frit, $\alpha$-Terpineol and ethyl cellulose. The EL device stack consists of Alumina substrate ($Al_2O_3$), metallic electrode (Au), insulating layer (manufactured PMN paste), phosphor layer (ELPP- 030, ELK) and transparent electrode (ITO), which is well structure as a thick film EL device. The phase transformation properties of PMN dielectric with various firing temperatures of $150^{\circ}C$ to $850^{\circ}C$ was characterized by XRD. Also the opto-electric properties of EL devices with different firing temperature were investigated by LCR meter and spectrometer. We found the best opto-electric property was obtained at the condition of $550^{\circ}C$ firing which is 3432.96 $cd/m^2$ at 1948.3 pF Capacitance, 40 kHz Frequency, 40% Duty, Vth+330 V voltage.