• 한국공작기계학회논문집
• /
• 제13권3호
• /
• pp.8-15
• /
• 2004

A significant error in the end milling processes is generated due to using slender tools of which the strengths are not sufficient. In order to obtain the desired machining accuracy, therefore, it is general that at first the rough cut is implemented, then the finish cut is followed. The rough cut eliminates large volume and the finish cut does the remained part. This remaining portion after the rough cut is called as the finish allowance. Larger finish allowances make it hard to get precise dimensions at a following finish cut. Smaller finish allowances are helpful for good dimension, but it sometimes is responsible for inferior surface qualities and over cuts. This study suggests a guidance for the optimum finish allowance for machining accuracy improvement, in which the rough cuts are regulated to remain the desired margins without any over cuts. Some experiments were carried out with various cutting conditions including the change of tool strengths and depth of cuts, and also extended to up millings as well as down millings.

• 한국공작기계학회논문집
• /
• 제15권6호
• /
• pp.38-43
• /
• 2006

A slot cut in end milling processes is one of the laborious works because the cutting force is likely to deflect the tools excessively, then to make large errors or to fracture the tool. This difficulty is owing to the poor stiffness of slender shaped end mills. Though, in most cases, additional finish cuts are followed after rough cuts, the accuracy of rough cuts is still important because it affects the final accuracy after finish cuts and productivity. The accuracy in slot cuts depends on the tool stiffness and the cutting conditions including depth of cut and feed. In order to meet the desired accuracy, diameter of end mill and cutting allowance have to be selected carefully. This study suggests several guidances for selecting the end mill diameter and the slot cut allowance to improve machining accuracy and productivity in slot end millings. Some experiments were done with the various cutting parameters of tool diameter, depth of cut and feed.

• 한국공작기계학회논문집
• /
• 제11권1호
• /
• pp.10-16
• /
• 2002

This study is to evaluate the tool performance in honing using diamond reamer and present grounds whether the localized products are sufficiently competitive comparing with the existing imported ones. The heads of the tool performance evaluation are roundness, roughness, tool life of the workpiece and so on. When evaluating the tool performance, cutting process is divided by three areas which are rough semi-finish and finish cut. cloning improves the accuracy such as boring and reaming after manufacturing the inside diameter, and finishing directly by honing is a recent trend. This honing is used greatly In hard cutting materials like cemented carbides and it is the CBN and diamond that is used in hard cutting materials. Both of them are expensive and most oi them are imported.

• 한국기계가공학회지
• /
• 제2권2호
• /
• pp.98-105
• /
• 2003

In the experimental study, wire EDM was conducted for cold die steel by changing the Wire electrode, peak discharge current and number of finish cut. From the micro structure analysis of SEM photographs, the size of irregular welded and added component on the EDMed surface is decreasing and size of EDMed plane surface is increasing as the decreasing peak current and increasing number of finish cut. From the analysis of coating effect, Zn component is highly contained in Br and Zn Wire EDMed surface and copper component is highly contained in Br and Al wire EDMed surface. Hardness values are Increasing as the increasing peak current and decreasing the number of finish cut The value of hardness is decreasing as Cu, Al, Zn and Br wire electrode because of the residual austenite effect of solid solution copper on solidification, and finally EDMed surface has the highest hardness values for every wire electrode. Yield strength values becomes larger and bending strength values become smaller due to the increasing the hardness. These results are increased as increasing brittleness with hardness.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2015년도 추계 학술논문 발표대회
• /
• pp.151-152
• /
• 2015

Concrete parking slab is often deteriorated severely after winter season because of concrete's freezing and thawing phenomenon. In this study, some methods to improve resistance against freezing-thawing is experimentally tested.: 1) concrete strength, 2) air content in concrete, 3) saw-cut effect and finish material. After experiment, in case of no finishes, 24MPa concrete with 4% air content is tested best result in terms of relative elastics modulus among testes ones. In case of concrete with finishes, all specimens are improved regardless of finishes compared to concrete with no finishes. Improvement degree compared to no finish is as follows : Polyurea > Resin-mortar > hardener and the number of improvement degree is 5, 4, 2% respectively. Further work is required considering construction site condition such as gaining water on surface and remicon in order to reflect site condition.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.64-70
• /
• 2001

This work deals with the electrical conductivity of dielectric and cobalt percentage on output parameters such as metal removal rate and surface roughness value of sintered carbides cut by wire-electrical discharge machining (W-EDM). To obtain a precise workpiece with good quality, some extra repetitive finish cuts along the rough cutting contour are necessary. Experimental results show that increases of cobalt amount in carbides affects the metal removal rate and worsens the surface quality as a greater quantity of solidified metal deposits on the eroded surface. Lower electrical conductivity of the dielectric results in a higher metal removal rate as the gap between wire electrode and workpiece reduced. Especially, the surface characteristics of rough-cut workpiece and wire electrode were analyzed too. To obtain a good surface equality without cracks, 4 finish-cuts were necessary by reducing the electrical energy and the offset value.

• 한국생산제조학회지
• /
• 제4권2호
• /
• pp.46-53
• /
• 1995

In this study, Wear of a ceramic cutting tool for hardened STD11 steel was investigated. Under the finish machining condition. DOC notch wear of a ceramic cutting tool was mostly occurred earlier than flank and crater wear were proceeded. The relations of DOC notch wear, which was characteristically produced at the beginning of cutting. to cutting speed, feed, depth of cut, and nose radius of a ceramic cutting tool were examined. Effective approach angle, which is a function of cutting conditions, and boundary area were suggested, and then the influence of those was investigated, The following conclusions were obtained: (1)as cutting speed was increasing. DOC notch wear was decreasing (2) the cutting condition that magnitude of slendermess ratio was made small, was favorable for DOC notch wear, (3) as depth of cut was smaller, the influence of feed on DOC notch wear was also smaller, (4) DOC notch wear was mainly influenced by effective approach angle, but by boundary area in the range of low feed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.956-959
• /
• 2001

In die and mould industry, major material such as cemented carbide is broadly used for increasing the life time and decreasing the cost. It is also required the development for the skills of wire-cut electrical discharge machining(WEDM), but the WEDMed surface was found to be worst due to the attached components of wire. Precision machining method like lapping is necessary for obtaining high quality surface. The lapping compound such as Al2O3 and SiC and cast iron lap can be used for lapping process. The components of Cu and Zn were found WEDMed surface of the specimen. As the result, the low quality of precision was obtained and the heat damage layer of the specimen was occurred. The value of surface hardness was deteriorated, and therefore finish process was required.

• Journal of Mechanical Science and Technology
• /
• 제15권12호
• /
• pp.1676-1682
• /
• 2001

This work deals with the electrical conductivity of dielectric and cobalts percentage on output parameters such as metal removal rate and surface roughness value of sintered carbides cut by wire-electrical discharge machining (WEDM). To obtain a precise workpiece with good quality, some extra repetitive finish cuts along the rough cutting contour are necessary, Experimental results show that increases of cobalt amount in carbides affects the metal removal rate and worsens the surface quality as a greater quantity of solidified metal deposits on the eroded surface. Lower electrical conductivity of the dielectric results in a higher metal removal rare as the gap between wire electrode and workpiece reduced. Especially, the surface characteristics of rough-cut workpiece and wire electrode were analyzed too. To obtain a good surface equality without crack, 4 finish-cuts were necessary reducing fille electrical energy and the offset value.

• 한국CDE학회논문집
• /
• 제3권4호
• /
• pp.236-242
• /
• 1998

This paper presents a development of computer aided cutting tool selection techniques for rough and finish turning operations. The developed system,. which is one of important activities for computer aided operation planning, firstly implements operation sequencing. Then, from relations of the size of machined area, recommended finishing allowance and maximum depth of cut, a main machining method is selected, a number of cut is calculated, cutting tools including toolholders and inserts are selected, and values for cutting parameters are determined. A cutting tool selection procedure is proposed for toolholders and inserts of ISO code in rough cutting, and some important parameters such as holder style, tool approach angle, tool function and its direction are described in detail. In order to demonstrate the validity of the system a case study is performed.