• Journal of Korean Society for Atmospheric Environment
• /
• v.16 no.5
• /
• pp.445-451
• /
• 2000

To estimate dry deposition flux of 12 elements in aerosols, aerosol particles were sampled by a low-pressure impactor(LPI) and a dust jar. The concentrations of 12 elements in aerosol particle and dry deposition were analyzed by a PIXE analysis using as a 2.0 MeV-proton beam. The mean dry deposition velocities of 12 elements were estimated by ranges of 0.74∼2.62 cm/sec. The results showed that the highest value was 3.26 cm/sec for Ca and the lowest value 0.74 cm/sec for Fe. The dry deposition flux for elements was calculated as a function of particle size by 1-step method and 12-step method. In this work, dry deposition velocities were computed with the two existing models; the coarse-particle fraction(4∼30 mm diameter) using the dry deposition velocity model of the Noll and Fang(1998) and the fine-particle fraction (0.05∼4mm diameter) using the Shemel and Hodgson(1980) model. The ratios of the mean calculated/measured fluxes were 3.59 for 1-step method and 0.60 for 12-step method respectively.

• Journal of Korean Society for Atmospheric Environment
• /
• v.20 no.6
• /
• pp.833-838
• /
• 2004

The analysis of Pb in both PM$_{2.5}$ and PM$_{10}$ fraction of aerosols was made consecutively for every spring season during four year period of 2001 through 2004. To diagnose the impact of the Asian Dust (AD) on metal concentration levels, we compared our Pb measurement data after dividing the whole data sets into AD and NAD period. The results of our analysis indicated that the concentrations of coarse particles increased significantly during the AD period, whereas an increase in the fine counterpart was of moderate degree. However, when Pb concentrations between AD and NAD were compared, the patterns were quite different. From all particle fractions, the Pb concentrations of NAD were slightly or moderately higher than those of AD. The overall results of our study suggest that an increase in particle concentrations during the AD period can cause a rather slight reduction in Pb concentration levels; this can be explained by the dilution effect associated with the increase of Pb-depleted coarse particles.s.s.

• Journal of the Korean Ceramic Society
• /
• v.34 no.11
• /
• pp.1173-1181
• /
• 1997

Effects of particle size distribution of alumina ceramics on behaviors of tape casting were investigated with emphases on the rheological characteristic of slurry, green density, green sheet strength, and sintering density. For the control of particle size distribution of alumina, the commercial grade low soda alumina, which had different mean particle size of 3.58 ${\mu}{\textrm}{m}$ and 0.42 ${\mu}{\textrm}{m}$, were chosen and blended together. As results, the mixing of 80 wt% fine powder and 20 wt% coarse powder(designated to FC20) led to the increase of packing density and strength of green sheet, and made it easy to handle during processing without lowering of sintering density. Besides, the pseudoplastic behavior of slurry decreased with increase of the fraction of coarse alumina powder.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.2
• /
• pp.584-595
• /
• 1991

In the direct rolling processes for the mushy state alloy, a mushy state material which simultaneously contains liquid-solid phase is obtained from the exit port of stirring apparatus with a given solid fraction. This solid fraction is dependent on the temperature of within the solid-liquid range which shows to be controlled accurately by the experimental conditions for a given stirring apparatus. Rolling conditions for fabrication the fine surface strip were obtained from direct rolling experiment with mushy state alloys of Sn-75%Pb and aluminum alloy. Influence of solid fraction, rolling speed and initial roller gap on the state of strip surface and solidified structure was observed. We proposed theoretical model for prediction of rolling force, and we compared calculation result and experimental value measured with load cell.

• Particle and aerosol research
• /
• v.5 no.4
• /
• pp.179-188
• /
• 2009

The dry deposition fluxes of particulate polychlorinated biphenyls (PCBs) were measured along with their mass size distributions at Seoul and Incheon in fall in 1999. The dry deposition fluxes of PCBs were in the range of $16.7{\sim}62.2ng/m^2/day$. The ambient concentrations of particulate PCBs were in the range of 0.07 to $0.20ng/m^3$. Generally, the mass size distribution of particulate PCBs shows bi-modal distribution. The mass fraction of PCBs in the fine particle fraction ($D_p<2.1 {\mu}m$) was over than 55% of the total PCBs concentrations. It was found that Seoul and Incheon were not the major source of PCBs emissions in Korea. Based on the comparison with the measurement data in summer, 1999, it is likely that both the dry deposition fluxes and ambient particulate PCBs concentrations were not site-specific.

• Advances in concrete construction
• /
• v.16 no.3
• /
• pp.169-176
• /
• 2023

The aim of the study was to establish the influence of particle size, chemical and phase composition of fine microspherical high-calcium fly ash (HCFA), as well as superplasticizer content on the strength of cementless composite materials based on 100% HCFA and mixtures of HCFA with Portland cement (PC). For the initial HCFA fractions, the particle size distribution, chemical and quantitative phase composition were determined. The compressive strength of cured composite materials obtained at W/B 0.4 and 0.25 was determined at a curing time of 3-300 days. For cementless materials, it was found that a change in the particle size d90 from 30 ㎛ (fraction 3) to 10 ㎛ (fraction 4) leads to an increase in compressive strength by more than 2 times. Compressive strength increases by at least another 2.2 times with the addition of Melflux 5581F superplasticizer (0.12%) and at W/B 0.25. The HCFA-PC blends were investigated in the range of 60-90% HCFA and the maximum compressive strength was found at 80% HCFA. On the basis of 80% HCFA-20% PC blend, the samples of ultra-high strength (108 and 150 MPa at 28 and 100 days of hardening) were obtained with the addition of 0.3% Melflux 5581F and 5% silica fume. The quantitative phase composition was determined for composite materials with a curing age of 28 days. It has been established that in a sample with ultra-high strength, a more complete transformation of the initial phases of both HCFA and PC occurs as compared to their transformation separately.

• Journal of the Korean Applied Science and Technology
• /
• v.30 no.4
• /
• pp.602-611
• /
• 2013

We have investigated the influence of system composition and preparation conditions on the particle size of vitamin E acetate (VE)-loaded nanoemulsions prepared by PIC(phase inversion composition) emulsification. This method relies on the formation of very fine oil droplets when water is added to oil/surfactant mixture. The oil-to-emulsion ratio content was kept constant (5 wt.%) while the surfactant-to-oil ratio (%SOR) was varied from 50 to 200 %. Oil phase composition (vitamin E to medium chain ester ratio, %VOR) had an effect on particle size, with the smallest droplets being formed below 60 % of VOR. Food-grade non-ionic surfactants (Tween 80 and Span 80) were used as an emulsifier. The effect of f on the droplet size distribution has been studied. In our system, the droplet volume fraction, given by the oil volume fraction plus the surfactant volume fraction, was varied from 0.1 to 0.3. The droplet diameter remains less than 350 nm when O/S is fixed at 1:1. The droplet size increases gradually as the increasing the volume fraction. Particle size could also be reduced by increasing the temperature when water was added to oil/surfactant mixture. By optimizing system composition and homogenization conditions we were able to form VE-loaded nanoemulsions with small mean droplet diameters (d < 50 nm). The PIC emulsification method therefore has great potential for forming nanoemulsion-based delivery systems for food, personal care, and pharmaceutical applications.

• Journal of Korean Society for Atmospheric Environment
• /
• v.16 no.2
• /
• pp.113-120
• /
• 2000

Effects of sea-salts on the properties of aerosol collected in a coastal region were studied by applying a gas-particle equilibrium model SCAPE to the measurement data from Korea Cheju Island in summer 1994. It was found that the observed higher ammonium concentrations in fine particles (PM2.5) than in TSP were caused by forced evaporation of ammonium in coarse fraction of aerosol by sea-salts and the degree of evaporation was quantified through an application of SCAPE. By subtracting the sea-salt fraction from the measured concentra-tions the changes of aerosol property were also studied. The concentrations of nitrate at both TSP and PM2.5 decreased when alkaline sea-salt fraction was removed from the measured data. Estimates of aerosol acidity increased for most samples with sea salt loadings, However in some cases with high mass fractions of sea-salt components the aerosol acidity of PM2.5 decreased slightly. This is though to be related with the formation of solid salt with the removal of sea-salts.

• Korean Journal of Food Science and Technology
• /
• v.28 no.3
• /
• pp.506-513
• /
• 1996

Soybean hull was microparticulated at cut-off wheel speed of 9,000 rpm and air-classified into fine and coarse fraction at air classifying wheel speeds (ACWS) of 10.000, 15,000 and 20,000 rpm. respectively. Proximate analysis of the coarse and fine fractions of the microparticulated/air-classified soybean hull showed that ash, protein and lipid were enriched in the coarse fractions and carbohydrates in the fine fraction. Dietary fiber were enriched in coarse fractions and dietary fiber and dietary fiber content increased with decreasing ACWS. Mean particle size of fine fractions ranged from $3.1{\mu}m\;to\;5.5{\mu}m$ that of coarse fractions ranged from $9.9{\mu}m\;to\;20.0{\mu}m$ and both increased with decreasing ACWS. The particles were mostly oval-shaped regardless of the fractions. Generally the fraction of low ACWS showed higher viscosity. In water holding capacity, oil absorption and emulsion capacity, there was significant difference between coarse and fine fractions while there was no significant difference as a function of different ACWS. Oil absorption of flying batter was decreased significantly in the fraction of ACWS 15,000. when cakes and cooking were prepared partially substituted with soybean hull fraction, there was no significant changes on their physical and sensory properties up to 10% substitution.

• Journal of Environmental Science International
• /
• v.29 no.1
• /
• pp.79-93
• /
• 2020

To determine the size distributions of water-soluble inorganic ionic species (WSIS) in roadside aerosols, sampling experiments were carried out in the urban roadside area of Jeju City on August 2018 and January 2019 by using the eight-stage cascade impactor sampler. The mass of roadside aerosols were partitioned at 57% in fine fraction, 36-37% in coarse fraction, and 6-7% in giant fraction, regardless of summer and winter. The mass concentrations of WSIS except for Na+ and SO42- in roadside aerosols were higher in winter than in summer. The size distributions of Na⁺, Mg²⁺, Ca²⁺ and Cl^- were characterized by bimodal types with coarse particle mode peaking around 3.3-4.7 ㎛ and 5.8-9.0 ㎛. The size distributions of NO₃^- and K⁺ shifted from a single fine mode peaking around 0.7-1.1 ㎛ in winter to bimodal and/or trimodal types with peaks around coarse mode in summer. SO₄^2- and NH₄⁺ showed a single fine mode peaking around 0.7-1.1 ㎛. The MMAD of roadside aerosols was lower than that of Na⁺, Mg²⁺, Ca²⁺ and Cl-. Based on the marine enrichment factors and the ratio values of WSIS and the corresponding value for sea water, the composition of roadside aerosols in Jeju City may be practically affected by terrestrial sources rather than marine source.