• 폴리머
• /
• 제25권4호
• /
• pp.528-535
• /
• 2001

본 연구에서는 polyol, MDI, 실리콘 유화제, 물을 기본 폴리우레탄 조성으로 설정하였으며, 경질 폴리우레탄 폼에 있어서 sitff-chain 요소인 에틸렌 글리콜의 첨가에 의하여 가교밀도가 증가하며, 이에 따른 셀의 크기, 발포 배율, cream time, gel time, take free time의 변화, 최종 자유 발포체 높이, 반응 온도, 단열도 변화를 관찰하였다. 발포제는 시클로펜탄을 사용하여 경질 물리우레탄을 발포하였으며, 상온, 상압에서 hand mixing 으로 5000 rpm, 4sec의 범위 안에서 혼합시킨 뒤에, 에틸렌 글리콜의 양을 변화시켜 200 ${\times}$ 200 ${\times}$ 200 mm 내의 나무 금형 안에서 발포 실험하였다. 이소시아네이트 인덱스를 고정시켰을 경우 에틸렌글리콜의 양이 증가함에 따라 셀의 크기는 약 5.1%와 열전도는 약 14%가 감소하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.1712-1716
• /
• 2008

Performance of ground improvement project using prefabricated vertical drains of condition, in which approximately 10m dredged fill overlies original soft foundation layer in the coastal area has been conducted. From field monitoring results, excessive ground settlement compared to predicted settlement in design stage developed during the following one year. In order to predict the final consolidation behavior, recalculation of consolidation settlements and back analysis using observed settlements were conducted. Field monitoring results of surface settlements were evaluated, and then corrected because large shear deformation was occurred by construction events in the early stages of consolidation. To predict the consolidation behavior, material functions and in-situ conditions from laboratory consolidation test were re-analyzed. Using these results, height of additional embankment is estimated to satisfy residual settlement limit and maintain an adequate ground elevation. The recalculated time-settlement curve has been compared to field monitoring results after additional surcharge was applied.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 봄 학술발표회 논문집
• /
• pp.491-498
• /
• 2002

Dredged and reclaimed soft clays form slurry state which is very high water content and very low shear strength, experience large self-weight consolidation, nonlinear compressibility and permeability phenomenon would take place. In this case, a material functions which represent variety effective stress-void ratio-permeability relation (especially very low effective stress), are should be determined to predict nonlinear finite strain consolidation phenomenon forehand In this study, large slurry consolidometer with a 380mm diameter and a 1400mm height which is able to consolidation and permeability test, was developed to determine material function of very soft clay with a 500% initial water content clay, self-weight consolidation and low stress level consolidation (1Kpa, 3Kpa, 6Kpa, 12Kpa) was conducted and after each consolidation step permeability test also conducted. after final consolidation step, a constant rate of strain consolidation was conducted with undisturbed sample obtained from the large consolidometer. On the above result, material function was determined and laboratory test was modelled to evaluate its validity, numerical analysis on th field was compared to other method.

• 대한지역사회영양학회지
• /
• 제4권1호
• /
• pp.64-73
• /
• 1999

We performed a study to understand the dietary situation in North Korea and to compare the difference between the North and the South. Two hundred North Korean defectors from the North since 1990 participated in this survey. Information was collected from December, 1997 to February, 1998 by mailing pre-tested questionnaires, which had been confirmed by 10 previous interviewers. The final data from 157 defectors(107 male and 33 female with 17 unidentified gender) were analyzed. We found that (1) North Koreans are lower in height, weight and BMI than South Koreans, (2) The North Korean diet is very simple and monotonous. It is limited to their local and unprocessed foods and dishes, which is far from the trend of globalization and readiness. (3) On the other hand, in the North, the government control on foods diminished because food shortage leads to free market activity where housewives manage their own foodservices, and to accelate their eating-out behaviors. (4) Profound differences between the South and the North in dietary life are noticed by the defectors as English words and Korean words. Efforts to understand and learn about each other is necessary before not too late.

• 한국작물학회지
• /
• 제45권5호
• /
• pp.310-315
• /
• 2000

Alfalfa (Medicago sativa L.) plants have been reported to contain water-soluble substances that are autotoxic as well as allelopathic. Laboratory experiment through a petri-dish assay with imbibed seeds was conducted to evaluate both autotoxic and allelopathic effects of alfalfa leaf extracts on the germination and early seedling growth of alfalfa, red clover, crested wheatgrass, and Russian wildrye. Alfalfa seed germination was delayed dependent on extract concentration, with no difference in final germination at 72 hours. Root growth of alfalfa was stimulated up to 14% above control at very low concentrations of both leaf and stem extracts of alfalfa and was significantly reduced at extract concentration of more than 0.5g dry tissue/L (${gL}_{-1}$). Leaf extracts were generally more autotoxic for root growth than were stem extracts. Hypocotyl growth was not affected by all the concentrations of both leaf and stem extracts. Root length of legumes was more sensitive to the autotoxic chemicals from leaf extracts than was germination or shoot length. Hypocotyl growth of two legume plants and plant height of two grasses were not influenced by extracts. Seed germination and root growth of legumes were more inhibited by aqueous extracts of alfalfa leaf than were those of grasses. This result indicates autotoxic effect of alfalfa leaf extracts seems to be greater than allelopathic effect.

• 한국자동차공학회논문집
• /
• 제14권5호
• /
• pp.121-129
• /
• 2006

An Intake Port of SI engines plays a key role on improving engine performance by maximizing full load volumetric efficiency or by optimizing in-cylinder air motion. However, designing an intake port has been usually performed based on port experts' experience and know-how, which means that analytical analyses are relatively insufficient. In this paper, port design parameters which decide an overall port shape were defined in order to correlate them relevantly with flow test results accumulated so far. Test species were composed of all twenty eight SI engines which cover major engine displacements from 1,000cc to 4,000cc. First, they were tested on a steady state flow test rig to find out their flow coefficients. Secondly, those flow coefficients were analyzed based on the port design parameters measured from the engines. The most effective parameters were port height, valve head diameter, and the ratio of port size and cylinder bore diameter. The final correlation equation could predict flow coefficients within 2% deviation.

• 한국군사과학기술학회지
• /
• 제16권6호
• /
• pp.811-818
• /
• 2013

In this paper, we have designed the elliptical dual offset gregorian antenna which can use Ka band earth station antennas in the fixed-satellite service. The structure of antenna is increasing the antenna gain by decreasing blockage areas and decreasing wind effects by shortening height of the antenna. The corrugate horn antenna for this antenna has symmetric radiation patterns and low side lobe levels that can meet ITU-R envelope. The distribution of electric field on a aperture of main reflector is calculated by an ray-tracing method that use the radiation pattern of the feed horn. The final geometric of antena is decided by choosing the distribution that comply with antenna requirement. The FEKO analysed electrical performance of this antenna. The fabricated antenna has 45.0dBi(@30.0GHz)/41.7dBi(@20.2GHz), high efficiency and low side lobe level that meet ITU-R S. 580-6 envelope.

• 소성∙가공
• /
• 제23권3호
• /
• pp.171-177
• /
• 2014

The current collector for the molten carbonate fuel cell (MCFC) which has sheared protrusions is manufactured by the three-stage forming process that integrates slitting, preforming and final forming. Due to the repetition of sheared protrusions, an effective simulation method is required to predict the mechanical behavior. In the current study, a sheet with sheared protrusions was assumed to be an orthotropic plate, which has the same length, width and height. FEM simulations were conducted to evaluate the homogenized properties of the current collector, which has 4 (longitudinal direction) x 4 (transverse direction) sheared protrusions. The simulation model was constructed using hexahedral mesh coarsening. From the verification examples, it was found that the proposed simulation method was efficient within reasonable accuracy. The calculated homogenized properties can be applied to the design of a stack for molten carbonate fuel cells and the prediction of mechanical behavior for other applications.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.269-272
• /
• 2008

LGP is a key component of LCD back light unit because it determines the brightness and sharpness of display image. Usually, it has optical patterns fabricated on the bottom surface. In the present paper the LiGA-reflow method was applied to fabricate the LGP mold. Furthermore, the optical simulation considering the replication ratio of pattern height was applied to the pattern design. The optical simulation through systematic correction scheme helped find the optimum distribution of pattern density. Finally, the stamper fabricated by this method was installed in the mold and LGP was produced by injection molding. As a result of luminance measurement for the final product, the average luminance and luminance uniformity was measured 3,180 nit and 84%, respectively. Consequently, the mold fabrication method using the LiGA-reflow and optical simulation(CAE) can save the expense and time compared with the existing fabrication methods(laser ablation and chemical etching).

• 패션비즈니스
• /
• 제14권6호
• /
• pp.146-169
• /
• 2010

For the purpose to develop the pattern of a tailored jacket for the Chinese adult women, a drawing method for the pattern of a tailored jacket was selected with the style of 'on&on', a young and casual brand of Beaucre Merchandising Co., Ltd. that has been successful in the China market, and then the measures to be applied were set up by properly combining the body measures such as the mean, mode and median of the entire group from data measured from women of 18 to 24 years old in Shanghai, China in 2008 and the mean body measures of the body type A of 2008 classified by GB/T 1335.2-1997. The pattern of a tailored jacket developed was verified for feasibility based on a wearing test and then revised for the parts with low jacket ability in general including the bust circumference, waist circumference, hip circumference, shoulder, waist back length and back area. The final measures applied for the development of a tailored jacket were 160-165cm for the height, the bust circumference of 87.7cm, waist circumference of 69.6cm and hip circumference of 92.8cm for a jacket.