• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.7 no.4
• /
• pp.135-141
• /
• 2008

Independent suspension axle and final reduction gear for special-purpose vehicles such as a armored vehicles are almost imported in Germany etc. so, developing them is necessary to save cost. In severe condition (open fields, water surface driving, obstacle pass), special-purpose vehicles must work well. Drop box, axle and final reduction gear performed static analysis. We know that is possible weight reduction. The purpose of this paper is to find out the optimal shape of final reduction gear's case by means of response surface methodology. The response surface method is the statistical method which can be applied to the non-sensitivity based optimization. The response surface which is constructed by the least square method contains only the polynomial terms so that the global maximum and minimum points are easily obtained.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.6 no.2
• /
• pp.67-75
• /
• 1997

The noise . vibration characteristics of Hypoid gears which were made from three seperate materials(SCM, TSCM, SNCM) under the identical process were investigated for the sake of durability improvement of differential gear compatible with low level noise gear set. For this study, we developed a rig experimental equipment which can perform close noise.vibration experiment of differential gear. Consequently, we could analyze the noise.vibration characteristics of final reduction gear by materials, and also we observed changes in both metallic structure and hardness according to the materials of pinion gear. In addition to this, the correlation between the vibration of the differential gear and the interior noise of the passenger vehicles was proved by analyzing the results of rig vibration experiment and field noise test.

• International Journal of Precision Engineering and Manufacturing
• /
• v.2 no.2
• /
• pp.65-72
• /
• 2001

The design of multi-stage gear drives is a time-consuming process, since on includes more complicated problems, which are not considered in the design of single-stage gear drives. The designer has th determine the number of reduction stages and the gear ratios of each reduction state. In addition, the design problems include not only the dimensional design but also the configuration design of gear drive elements. There is no definite rule and principle for these types of design problems. Thus the design practices largely depend on the sense and the experiences of the designer , and consequently result in undesirable design solution. We propose a new generalized design algorithm to support the designer at the preliminary design phase of multi-stage gear drives. The proposed design algorithm automates the design process by integrating the dimensional design and the configuration design process. The algorithm consists of four steps. In the first step, a designer determines the number of reduction stage. In the second step. gear ratios se chosen by using the random search method. In the third step, the values of basic design parameter are chosen by using the generate and test method. Then, the values of other dimension, such ad pitch diameter, outer diameter, and face width, are calculated for the configuration design in the final step. The strength and durability of a gear is guaranteed by the bending strength and the pitting resistance rating practices by using the AGMA rating formulas. In the final step, the configuration design is carried out b using the simulated annealing algorithm. The positions of gears and shafts are determined to minimize the geometrical volume(size) of a gearbox, while satisfying spatial constraints between them. These steps are carried out iteratively until a desirable solution is acquired. The propose design algorithm has been applied to the preliminary design of four-stage gear drives in order to validate the availability. The design solution have shown considerably good results in both aspects of the dimensional and the configuration design.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1996.10a
• /
• pp.174-184
• /
• 1996

Two methods for cold extrusion processes to produce an axisymmetric steel gear blank are investigated for comparing each other. The "classical" forming method consisting of four operations is selected first to be simulated using the rigid-plastic finite element method and uses single-die presses. The other using a fully automated transfer headers can produce the final part without interannealing. The final products must be checked at the design criteria such as area reduction, the extrusion ratio and punch diameter to depth ratio, especially punch buckling by simulations. FEM analysis is performed mainly for strain distribution, both process sequences are proved to have proper charicteristics suitable for each production method in terms of maximum load. Those simulation results will provide good design criteria in the future work to advance the manufacturing process.

• Proceedings of the KSR Conference
• /
• 1999.11a
• /
• pp.99-106
• /
• 1999

Because many light rail transit systems are mainly operated in the downtown areas of a large cities and the congestion areas, there are many steep gradients and sharp radius sections in that lines. As that reasons above, light rail vehicles are equipped with differential gear units between traction motors and final reduction gear units. In this paper, the configurations and the interferences of 2K-H I type Planetary gear train, which is applicable for light rail vehicles and based on various differential gear units, are studied. The ranges of addendum modification coefficients which would not lead to interferences is analyzed, and optimal addendum modification coefficients among these ranges are presented, which generate the maximum efficiency of planetary gear drives and differential gear unit as pressure angles, speed ratios,

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.12
• /
• pp.157-164
• /
• 1995

Straight belvel gear is used mainly for steering system, final reduction and differential gear in the automobile. The more high load, high velocity driving bevel gear, the more unsafe and unpleasant. In thid study, we get a kinematic equation by modelling straight bevel gear pair with simple elastic system, the dynamic characteristic analysis about this system, we got the dynamic load factor of tooth surface. Comparing the value of dynamic load factor by calculation with the measured value of Terauchi's experimental results is similar. We think it useful to analysis the vibration and the noise of straight bevel gear in operation with the analytic method of dynamic load of straight bevel gear using in this study.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.10
• /
• pp.192-199
• /
• 2000

The design of multi-stage gear drives is a time-consuming process because it includes more complicated problems, which are not considered in the design of single-stage gear drives. The designer has no determine the number of reduction stages and the gear ratios of each reduction stage. In addition, the design problems include not only dimensional design but also configuration design of gear drive elements. There is no definite rule or principle for these types of design problems. Thus the design practices largely depend on the sense and the experiences of the designer, and consequently result in undesirable design solution. A new and generalized design algorithm has been proposed to support the designer at the preliminary phase of the design of multi-stage gear drives. The proposed design algorithm automates the design process by integrating the dimensional design and the configuration design process. The algorithm consists of four steps. In the first step, the user determines the number of reduction stages. In the second step, gear ratios of every stage are chosen using the random search method. The values of the basic design parameters of a gear are chose in the third step by using the generate and test method. Then the values of the dimensions, such as pitch diameter, outer diameter and face width, are calculated for the configuration design in the next step. The strength and durability of each gear is guaranteed by the bending strength and the pitting resistance rating practices by using AGMA rating formulas. In the final step, the configuration design is carried out using simulated annealing algorithm. The positions of gears and shafts are determined to minimize the geometrical volume (size) of a gearbox while avoiding interferences between them. These steps are carried out iteratively until a desirable solution is acquired. The proposed design algorithm is applied to the preliminary design of four-stage gear drives in order to validate the availability. The design solution has considerably good results in both aspects of the dimensional and the configuration design.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.10
• /
• pp.54-59
• /
• 2019

The final reduction drive in tactical vehicles has a wear-pad that helps to maintain adequate end floating when the hub assay operates. The input axis and sun gear move repeatedly with the axis when tactical vehicle is operating. The hub assay is designed so that the wear pads won't seize during operation. Seizure of the wear pads during operation results in oil leakage. In our study, the fault mechanism was analyzed to prevent the seizure of the wear pads and an optimal design for the shape and material of the wear-pad was explored. We then observed the changes in temperature, shape, and material of several important parts.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.9
• /
• pp.116-121
• /
• 2020

In recent times, fuel economy enhancement and environmental regulation compliance have become the main topics of interest in the automobile industry. Electric vehicles are desirable alternatives to the existing cars that employ internal combustion engines. Specifically, electric vehicles are equipped with inverters, motors, and a gearbox instead of engines and transmission mechanisms. The gearbox is a key component, used to transmit power from the electric motor to the wheel. Therefore, the design of the gearbox is critical. However, most engineers design gears based only on their experience because no standards pertaining to the design factor exist, other than those for the gear ratios. To overcome this problem, the structural stabilities must be examined considering the design factors of the gears. In this study, we considered the module and number of teeth as the main factors. The constraints corresponded to the final gear ratio and fixed distance between each axle of the shafts. Moreover, a structural analysis was conducted, and the variation trend of the maximum equivalent stress against changes in the gear module and number of teeth was examined. By performing such an analysis, the structural stability in the design of a gear system could be effectively investigated.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.5
• /
• pp.559-566
• /
• 2016

This study shows a development procedure and results of noise reduction for a new developed FF 8th speed automatic transmission. Based on planetary gear operating frequency analysis using PTA(planetary transmission analysis) program developed in 2012, It is expected that gear noise of the rear planetary gear set could be recognized easily in the concept design stage. Therefore, pRMC (planetary run many cases) analysis program that is developed in 2012 was applied to minimize the planetary gear noise level and noise distributions versus torque. To minimize noises coming from oil pump and final gears of a new transmission, several changes were applied, such as changing the clearance of double angular ball bearing, the oil pump rotor tooth number from 9 to 11 and the oil pump type from parachoid to megafloid and so on. Besides, stiffness values of the transmission case and the mount bracket were measured and reinforced properly. Finally, The total noise of the new FF 8th speed automatic transmission was developed successfully. Furthermore, E.O.L. testers also have been adapted to control the noise quality of automatic transmission assembly in the manufacturing factory. This paper could provide practical solutions to the automatic transmission NVH problems.