• Journal of Electrical Engineering and Technology
• /
• v.12 no.5
• /
• pp.1945-1954
• /
• 2017

In recent years, several LCL filter design methods for different converter topologies have been published, many of which use analytical expressions to calculate the ideal converter AC voltage harmonic spectrum. This paper presents the LCL filter design methodology but the focus is on presentation and validation of the non-iterative filter design method for a grid-connected three-phase two-level PWM-VSC. The developed method can be adapted for different converter topologies and PWM algorithms. Furthermore, as a starting point for the design procedure, only the range of PWM carrier frequencies is required instead of an exact value. System nonlinearities, usually omitted from analysis have a significant influence on VSC AC voltage harmonic spectrum. In order to achieve better accuracy of the proposed procedure, the system nonlinear model is incorporated into the method. Optimal filter parameters are determined using the novel cost function based on higher frequency losses of the filter. An example of LCL filter design for a 40 kVA grid-connected PWM-VSC has been presented. Obtained results have been used to construct the corresponding laboratory setup and measurements have been performed to verify the proposed method.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.3
• /
• pp.419-427
• /
• 2016

This paper proposes a design method of LCL-filter for a grid-connected three-phase inverter using a discontinuous PWM (DPWM) method. When using a DPWM method, many harmonic voltages are generated in the inverter output compared to a continuous PWM (CPWM) method. Therefore, an optimized grid-connected filter design is required for a DPWM method. The proposed design method provides generalized formula to design accurate LCL-filter without trial and error procedures. An inverter side inductance is designed by analyzing the current ripple injected to the grid. The Optimized parameters of LCL-filter can be designed by analyzing the total harmonic distortion (THD) and the ripple attenuation factor of the output current. The proposed LCL filter design method is demonstrated by simulation and experimental results.

• Proceedings of the Korea Institute of Convergence Signal Processing
• /
• 2003.06a
• /
• pp.268-271
• /
• 2003

There are several methods for the design of 2D filter. Notable among them is McClellan transform method. This transform allows us to obtain a high order 2D FIR filter through mapping the 1D frequency points of a 1D prototype FIR filter onto 2D frequency contours. We design 2D filter using this transform. Then we notice for mapping deviation of the 2D filter. In this paper, Quadratic programming (QP) method allows us to obtain coefficients of McClellan transform. Then we compare deviation of QP method with least-squares(LS) method. Elliptic filter is used for comparison. The optimal cutoff frequencies of a 1D filter are obtained directly from the QP method. Also several problem of LS method are solved.

• Journal of the Korean Society of Safety
• /
• v.12 no.4
• /
• pp.63-69
• /
• 1997

This paper presents a design method for a filter application in a parts-of FA(Factory Automation). Normal equations for ripple voltage and current are derived in terms of dimensionless quantities, and these equations can be used directly to evaluate the values of LC-filter components, taking into consideration the effect of the ripple components on the rms value of the PWM-generated ripple components. Using describing function technique, design equations of the filter are derived. The data needed for the filter evaluation are the amplitude of current ripple and the frequency of square pulses delivered by the HE(Harmonic Elimination) inverter algorithm. Experimental results show that the design of the filter can be based on the method proposed and that the filter can provide a significant reduction of ripple components.

• Proceedings of the KIEE Conference
• /
• 2005.07a
• /
• pp.465-467
• /
• 2005

Filter design for harmonic reduction suggests that measurement from IEEE std-519 and IEEE-61000 standards for 1 year designs filter about the worst case, filter design about method applied probability from IEEE std-519 standard suggests the basic alternative. At filter design method applied to temporary occurred harmonic maximum, analyzed into closely harmonic that applied to probability develops that ignorable harmonic that lowers temporary occurred probability is rational and economic filter design in detailed method.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.5
• /
• pp.490-498
• /
• 2002

In this paper, a design method of LCL filter at the AC input side of a voltage source PWM converter is proposed. Effective method to prevent pollution of the utility caused by high frequency current ripple is to use a AC input LCL filter, The C elements in the filter provide a low impedance path for the high frequency component, preventing them from entering the utility. The resistors In series with the capacitors are used for damping the resonance in the filter The design examples are shown and the validity of the proposed design method is verified through the PSIM simulation.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.54 no.9
• /
• pp.570-576
• /
• 2005

In FIR (Finite Impulse Response) filter applications, Nth-band FIR digital filters are known to be important due to their reduced computational requirements. The conventional methods for designing FIR filters use iterative approaches such as the well-known Parks-Mcclellan algorithm. the Parks-Mcclellan algorithm is also used to design Nth-band FIR digital filters. But a disadvantage of the Parks-McClellan algorithm Is that it needs a good amount of design time. This paper describes a direct design method for third-band FIR Filters using Chebyshev polynomial, which provide a reduction in design time over indirect methods such as the Parks-McClellan algorithm. The response of the resulting filter is equi-ripple in passband. The proposed method of design produces a passband response that is equi-ripple to within a minuscule error, compare to that of the Parks-McClellan algorithm.

• Journal of Power Electronics
• /
• v.9 no.4
• /
• pp.623-630
• /
• 2009

This paper proposes a filter design guideline for grid-connected single-phase inverters. By analyzing the instantaneous voltage applied to the filter inductor, the switching ripple current through the filter inductor can be precisely calculated. Therefore, filter inductance can be designed accurately, which guaranties that the switching ripple current will be under the target value. The proposed filter design method is verified by experiment.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.506-509
• /
• 2002

In this paper, a design method of LCL filter at the AC input side of a voltage source PWM converter is proposed. Effective method to prevent pollution of the utility caused by high frequency current ripple is to use a LCL filter instead of the L filter The C elements in the filter provide a low impedance path for the high frequency component, preventing them from entering the utility. A resistor in series with a capacitor is used for damping the resonance in the filter. The design examples are shown and the validity of the proposed design method is verified through the PSIM simulation.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.1
• /
• pp.103-109
• /
• 2013

The conventional LCL filter design method of the utility interactive inverter considers only harmonics attenuation of the current injected to the grid. However, in case of utility-interactive inverter with critical load the voltage quality of the critical load should also be considered for LCL filter design. Also, considering cost and volume of LCL filters. it is important to have minimum values of inductance and capacitance as far as the harmonic standards are satisfied. In this paper a LCL filter design method is proposed to satisfy not only the harmonic standards of the grid current during the grid-connected mode but the voltage quality of the critical load during grid-connected mode and stand-alone mode. With the proposed method optimized values of LCL filters could be obtained by applying weighting factor to voltage ripple across the critical load, inductor volume, amount of reactive current and system bandwidth.