• 한국태양에너지학회:학술대회논문집
• /
• 2011.04a
• /
• pp.105-110
• /
• 2011

The doping procedure in crystalline silicon solar cell fabrication usually contains oxygen injection during drive-in process and removal of phosphorous silicate glass(PSG). In this paper, we studied the effect of oxygen injection and PSG on conversion efficiency of solar cell. The mono crystalline silicon wafers with $156{\times}156mm^2$, $200{\mu}m$, $0.5-3.0{\Omega}{\cdot}cm$ and p-type were used. After etching $7{\mu}m$ of the surface to form the pyramidal structure, the P(phosphorous) was injected into silicon wafer using diffusion furnace to make the emitter layer. After then, the silicon nitride was deposited by the PECVD with 80 nm thickness and 2.1 refractive index. The silver and aluminium electrodes for front and back sheet, respectively, were formed by screen-printing method, followed by firing in 400-425-450-550-$880^{\circ}C$ five-zone temperature conditions to make the ohmic contact. Solar cells with four different types were fabricated with/without oxygen injection and PSG removal. Solar cell that injected oxygen during the drive-in process and removed PSG after doping process showed the 17.9 % conversion efficiency which is best in this study. This solar cells showed $35.5mA/cm^2$ of the current density, 632 mV of the open circuit voltage and 79.5 % of the fill factor.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.10
• /
• pp.3052-3058
• /
• 2014

In this article, we have designed and synthesized a novel donor-${\pi}$-acceptor (D-${\pi}$-A) type porphyrin-based sensitizer (denoted UI-5), in which a carboxyl anchoring group and a 9,9-dimethyl fluorene were introduced at the meso-positions of porphyrin ring via phenylethynyl and ethynyl bridging units, respectively. Long alkoxy chains in ortho-positions of the phenyls were supposed to reduce the degree of dye aggregation, which tends to affect electron injection yield in a photovoltaic cell. The cyclic voltammetry was employed to determine the band gap of UI-5 to be 1.41 eV based on the HOMO and LUMO energy levels, which were estimated by the onset oxidation and reduction potentials. The incident monochromatic photon-to-current conversion efficiency of the UI-5 DSSC assembled with double-layer (20 nm-sized $TiO_2$/400 nm-sized $TiO_2$) film electrodes appeared lower upon overall ranges of the excitation wavelengths, but exhibited a higher value over the NIR ranges (${\lambda}$ = 650-700 nm) compared to the common reference sensitizer N719. The UI-5-sensitized cell yielded a relatively poor device performance with an overall conversion efficiency of 0.74% with a short circuit photocurrent density of $3.05mA/cm^2$, an open circuit voltage of 0.54 mV and a fill factor of 0.44 under the standard global air mass (AM 1.5) solar conditions. However, our report about the synthesis and the photovoltaic characteristics of a porphyrin-based sensitizer in a D-${\pi}$-A structure demonstrated a significant complex relationship between the sensitizer structure and the cell performance.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.2
• /
• pp.569-574
• /
• 2014

Inverted bulk hetero-junction polymer solar cells (iPSC) composed of P3HT/PC61BM blends on the ZnO modified with benzoic acid derivatives-based self-assembled monolayers (SAM) are fabricated. Compared with the device using the pristine ZnO, the devices with ZnO surface modified SAMs derived from benzoic acid such as 4-(diphenylamino)benzoic acid (DPA-BA) and 4-(9H-carbazol-9-yl)benzoic acid (Cz-BA) as an electron transporting layer show improved the performances. It is mainly attributed to the favorable interface dipole at the interface between ZnO and the active layer, the eective passivation of the ZnO surface traps, decrease of the work function and facilitating transport of electron from PCBM to ITO electrode. The power conversion eciency (PCE) of iPSCs based on DPA-BA and Cz-BA treated ZnO reaches 2.78 and 2.88%, respectively, while the PCE of the device based on untreated ZnO is 2.49%. The open circuit voltage values ($V_{oc}$) of the devices with bare ZnO and SAM treated ZnO are not much different. Whereas, higher the fill factor (FF) and lower the series resistance ($R_s$) are obtained in the devices with SAMs modification.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.34-39
• /
• 2011

Screen printing method is a common way to fabricate the crystalline silicon solar cell with low-cost and high-efficiency. The screen printing metallization use silver paste and aluminum paste for front and rear contact, respectively. Especially the rear contact between aluminum and silicon is important to form the back surface filed (Al-BSF) after firing process. BSF plays an important role to reduces the surface recombination due to $p^+$ doping of back surface. However, Al electrode on back surface leads to bow occurring by differences in coefficient of thermal expansion of the aluminum and silicon. In this paper, we studied the properties of mono crystalline silicon solar cell for rear electrode with aluminum and aluminum-boron in order to characterize bow and BSF of each paste. The 156*156 $m^2$ p-type silicon wafers with $200{\mu}m$ thickness and 0.5-3 ${\Omega}\;cm$ resistivity were used after texturing, diffusion, and antireflection coating. The characteristics of solar cells was obtained by measuring vernier callipers, scanning electron microscope and light current-voltage. Solar cells with aluminum paste on the back surface were achieved with $V_{OC}$ = 0.618V, JSC = 35.49$mA/cm^2$, FF(Fill factor) = 78%, Efficiency = 17.13%.

• Journal of the Korean Solar Energy Society
• /
• v.31 no.1
• /
• pp.37-43
• /
• 2011

In this paper, the optimized doping condition of crystalline silicon solar cells with $156{\times}156\;mm^2$ area was studied. To optimize the drive-in temperature in the doping process, the other conditions except variable drive-in temperature were fixed. These conditions were obtained in previous studies. After etching$7\;{\mu}m$ of the surface to form the pyramidal structure, the silicon nitride deposited by the PECVD had 75~80nm thickness and 2 to 2.1 for a refractive index. The silver and aluminium electrodes for front and back sheet, respectively, were formed by screen-printing method, followed by firing in 400-425-450-550-$850^{\circ}C$ five-zone temperature conditions to make the ohmic contact. Drive-in temperature was changed in range of $830^{\circ}C$ to $890^{\circ}C$to obtain the sheet resistance $30{\sim}70\;{\Omega}/{\box}$ with $10\;\Omega}/{\box}$ intervals. Solar cell made in $890^{\circ}C$ as the drive-in temperature revealed 17.1% conversion efficiency which is best in this study. This solar cells showed $34.4\;mA/cm^2$ of the current density, 627 mV of the open circuit voltage and 79.3% of the fill factor.

• Current Photovoltaic Research
• /
• v.2 no.3
• /
• pp.135-139
• /
• 2014

Different power output of solar cells can be observed at high-temperature regions such as desert areas. In this study, performance dependence on operating temperature of crystalline silicon solar cells with different emitter types was analyzed. Based on the light current-voltage (LIV) measurement, temperature coefficients of short-circuit current density ($J_{SC}$), open-circuit voltage ($V_{OC}$), fill factor (FF) and power conversion efficiency were measured and compared for two groups of crystalline silicon solar cells with different emitter types. One group had homogeneously doped (conventional) emitter and another selectively doped (selective) emitter. Varying the operating temperature from 25 to 40, 60, and $80^{\circ}C$, LIV characteristics of the cells were measured and the properties of saturation current densities ($J_0$) were extracted from dark current-voltage (DIV) curve. From the DIV data, effect of temperature on the performance of the solar cells with different electrical structures for the emitter was analyzed. Increasing the temperature, both emitter structures showed a slight increase in $J_{SC}$ and a rapid degradation of $V_{OC}$. FF and power conversion efficiency also decreased with the increasing temperature. The degrees of $J_{SC}$ increase and $V_{OC}$ degradation for two groups were compared and explained. Also, FF change was explained by series and shunt resistances from the LIV data. It was concluded that the degradation of solar cells shows different values at different temperatures depending on the emitter type of solar cells.

• Korean Journal of Community Nutrition
• /
• v.8 no.5
• /
• pp.642-651
• /
• 2003

This study was performed using mealtime atmosphere to characterize the food ecology of Korean children residing in different regions of Korea. A total of 705 elementary school students, 347 girls and 358 boys, were divided into three groups according to the areas where they lived, which included Seoul (n=230), provincial cities (n=273) and rural areas (n=202). The subjects were asked to fill out questionnaires which were categorized to determine various factors related to food ecology, life styles, and health related symptoms. The average age of the study subjects was 11.5 years. The results showed that the average height (p<0.01), weight (p<0.01) and body mass index (BMIs) (p< 0.01) of the rural group were significantly lower than those of the Seoul and provincial city groups. A significantly higher proportion (10.4%) of the rural group was from disfunctional families, including single parent families, than those of the Seoul (1.7%) or provincial city (4.4%) groups. However, a larger number of children from Seoul ate alone, did not enjoy their meals, and hardly talked to each other during breakfast time, compared to those from the provincial city or rural areas. Also, the proportion (33.0%) of ‘good’ in balance of meal was the lowest (33.0%) in Seoul of the three areas (p<0.01). Most of the children answered that they liked having breakfast and dinner with the whole family. In conclusion, the food ecology of elementary children differed according to the regions in which they resided. Although children from Seoul had higher BMIs, their nutritional intake was not satisfactory, and their undesirable food ecology could be a contributing factor.

• The Bulletin of The Korean Astronomical Society
• /
• v.41 no.1
• /
• pp.41.2-41.2
• /
• 2016

The follow-up BVRI photometric observations of NSVS 1461538, which was discovered as an $Algol/{\beta}$ Lyr eclipsing variable by Hoffman, Harrison & McNamara (2009), were performed for three years from 2011 to 2013 by using the 61-cm telescope and CCD cameras of Sobaeksan Optical Astronomy Observatory (SOAO). New light curves have deep depths both of the primary and secondary eclipses, rounded shapes outside eclipses and a strong O'Connell effect, indicating that NSVS 1461538 is a typical W UMa close binary system rather than an $Algol/{\beta}$ Lyr type binary star. A period study with all the timings shows that the orbital period may vary in a sinusoidal way with a period of about 5.6 yr and a small semi-amplitude of about 0.008 d. The cyclical period variation was interpreted as a light-time effect due to a tertiary body with a minimum mass of $0.66M{\odot}$. The first photometric solution with the Wilson-Devinney binary model shows that the system is a W-subtype contact binary with the mass ratio ($q=m_c/m_h$) of 3.46, orbit inclination of 85.6 deg and fill-out factor of 30%. From the existing empirical relationship between parameters, the absolute dimension was estimated. The masses and radii of the component stars are $0.28M{\odot}$ and $0.71R{\odot}$ for the less massive but hotter primary star, respectively, and $0.96M{\odot}$ and $1.21R{\odot}$ for the more massive secondary, respectively. Possible evolution of the system is discussed in the mass-radius and the mass-luminosity planes.

• Journal of the Korean housing association
• /
• v.25 no.4
• /
• pp.31-38
• /
• 2014

The present research aimed at researching the relationships among place attachment, residential evaluations and satisfaction in a medium-sized post-communist Romanian city. Studies on post-communist cities are scarce and this research tried to fill that gap. This research is part of a government project that intended to significantly reform three medium-sized cities in the Western part of Romania and transform the urban space. Since the three of them are relatively small-sized and close spatially, the project intends to undertake massive reforms of the communications and services of the three cities. In this article, we report findings on the city of Hunedoara. A representative random sample was selected, and a total of 384 people were interviewed, with an overall reliability of the sample of 95%. The instruments used to gather the data were the Neighbourhood Perceived Environmental Quality Scale and a composite measure of place attachment was also included. The structure of each scale was checked using exploratory factor analysis. We tested alternative causal models using structural equations modelling. Our model showed a good fit to the data and explains satisfaction in the city adequately. Results show that satisfaction is directly predicted by the general evaluation of the city and by residential privacy. Residential noise and place attachment influence satisfaction indirectly. The results are discussed and some policy recommendations are formulated.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.1
• /
• pp.33-40
• /
• 2007

We have designed and synthesized three Zn(II)-porphyrin derivatives, such as Zn(II) porphyrin ([G-0]Zn-P1) and aryl ether-typed dendron substituted Zn(II)-porphyrin derivatives ([G-1]Zn-P1 and [G-1]Zn-P-CN1). Their chemical structures were characterized by 1H-NMR, FT-IR, UV-vis absorption, EI-mass, and MALDI-TOF mass spectroscopies. Their electrochemical properties were studied by cyclic voltammetry measurement. These Zn(II)-porphyrin derivatives have been used to fabricate dye-sensitized solar cells (DSSCs) based on solid polymeric electrolytes as dye sensitizers and their device performances were evaluated by comparing with that of a standard Ru(II) complex dye. [G-1]Zn-P-CN1 showed the enhanced power conversion efficiency than those of other porphyrin derivatives, as expected. Short-circuit photocurrent density (Jsc), open-circuit voltage (Voc), fill factor (FF), and power conversion efficiency (η) of solid-typed DSSC for [G-1]Zn-P-CN1 were evaluated to be Jsc = 11.67 mA/cm2, Voc = 0.51 V, FF = 0.46, and η = 2.76%, respectively.