• Journal of the Korean institute of surface engineering
• /
• v.41 no.4
• /
• pp.147-155
• /
• 2008

The dental orthodontic wire provides a good combination of strength, corrosion resistance and moderate cost. The purpose of this study was to investigate the effects of TiN and ZrN coating on corrosion resistance and physical property of orthodontic wire using various instruments. Wires(round type and rectangular type) were used, respectively, for experiment. Ion plating was carried out for wire using Ti and Zr coating materials with nitrogen gas. Ion plated surface of each specimen was observed with field emission scanning electron microscopy(FE-SEM), energy dispersive X-ray spectroscopy(EDS), atomic force microscopy(AFM), vickers hardness tester, and electrochemical tester. The surface of TiN and ZrN coated wire was more smooth than that of other kinds of non-coated wire. TiN and ZrN coated surface showed higher hardness than that of non-coated surface. The corrosion potential of the TiN coated wire was comparatively high. The current density of TiN coated wire was smaller than that of non-coated wire in 0.9% NaCl solution. Pit nucleated at scratch of wire. The pitting corrosion resistance $|E_{pit}-E_{rep}|$ increased in the order of ZrN coated(300 mV), TiN coated(120 mV) and non-coated wire(0 mV).

• Journal of the Korean institute of surface engineering
• /
• v.47 no.4
• /
• pp.198-203
• /
• 2014

ZnO nanorods have been deposited on ITO glass by electrodeposition method. The optimization of two process parameters (precursor concentration and current) has been studied in order to control the orientation, morphology, and optical property of the ZnO nanorods. The structural and optical properties of ZnO nanorods were systematically investigated by using field-emission scanning electron microscopy, X-ray diffractometer, and photoluminescence. Commonly, the results show that ZnO nanorods with a hexagonal form and wurtzite crystal structure have a c-axis orientation and higher intensity for the ZnO (002) diffraction peaks. Both high precursor concentration and high electrodeposition current cause the increase in nanorods diameter and coverage ratio. ZnO nanorods show a strong UV (3.28 eV) and a weak visible (1.9 ~ 2.4 eV) bands.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.337-337
• /
• 2012

Dye sensitized solar cell (DSSC) having high efficiency with low cost was first reported by Gr$\ddot{a}$tzel et al. Many DSSC research groups attempt to enhance energy conversion efficiency by modifying the dye, electrolyte, Pt-coated electrode, and $TiO_2$ films. However, there are still some problems against realization of high-sensitivity DSSC such as the recombination of injected electrons in conduction band and the limited adsorption of dye on $TiO_2$ surface. The surface of $TiO_2$ is very important for improving hydrophilic property and dye adsorption on its surface. In this paper, we report a very efficient method to improve the efficiency and stability of DSSC with nano-structured $TiO_2$. Atmospheric plasma system was utilized for nitrogen plasma treatment on nano-structured $TiO_2$ film. We confirmed that the efficiency of DSSC was significantly dependent on plasma power. Relative in the $TiO_2$ surface change and characteristics after plasma was investigated by various analysis methods. The structure of $TiO_2$ films was examined by X-ray diffraction (XRD). The morphology of $TiO_2$ films was observed using a field emission scanning electron microscope (FE-SEM). The surface elemental composition was determined using X-ray photoelectron spectroscopy (XPS). Each of plasma power differently affected conversion efficiency of DSSC with plasma-treated $TiO_2$ compared to untreated DSSC under AM 1.5 G spectral illumination of $100mWcm^{-2}$.

• Korean Journal of Materials Research
• /
• v.10 no.8
• /
• pp.558-563
• /
• 2000

$Y_2SiO_5:Ce$ phosphor was coated with $In_2O_3$, $Al_2O_3$ and $SiO_2$ and then their cathodoluminance(CL)proper-ties required in field emission display were investigated. It was found that luminance efficiency and aging p개perty of $Y_2SiO_5:Ce$ phosphor was decreased with $In_2O_3$coating. For the case of coating, the luminance intensity was in blue phosphor was dramatically increased with $SiO_2$ coating. And also the aging property of $Y_2SiO_5:Ce$ Phosphor coated with $SiO_2$ was significantly improved compared to non-coated sample.

• Applied Chemistry for Engineering
• /
• v.24 no.1
• /
• pp.104-111
• /
• 2013

Poymer blends of two degradable aliphatic polyesters, relatively expensive material polylactic acid (PLA) and relatively inexpensive material poly(butylene adipate-co-terephthalate) (PBAT), were used in this study. Three different kinds of modifiers were used with various amounts. Diisocyanate type methylenediphenyl 4,4'-diisocyanate (MDI) and hexamethylene diisocyanate (HDI) were used as modifiers and epoxy type coupling agents also used. The melt flow index (MFI) and dynamic viscoelasticity of various compositions of PLA/PBAT blends were studied. The mechanical property and morphology with respect to the fracture surface of PLA/PBAT blends were also investigated using tensile test and field emission scanning electronic microscopy, respectively. These tests were also used to verify the compatibility of PLA/PBAT and the effect of mechanical properties due to the use of modifiers. Tensile properties of PLA/PBAT blends modified with HDI were improved remarkably.

• Journal of the Korean Chemical Society
• /
• v.46 no.2
• /
• pp.164-168
• /
• 2002

SrGa$_2$S$_4$ : Eu is a green emitting phosphor which is applied for field emission display, and cathodoluminescence. Conventionally, SrGa$_2$S$_4$ : Eu is synthesized by solid state reaction, in which a mixture of SrCO$_3$, Ga$_2$O$_3$, and Eu$_2$O$_3$ is fired at high temperatures under flowing H$_2$S and Ar gases. In this study,SrGa$_2$S$_4$ : Eu phosphor is synthesized by using a decomposition method, where SrS, Eu complex, and Ga com-plex are used. The advantage of this method is that toxic H$_2$S gas and Ar gas are not used. The synthetic con-ditions and luminescent properties of SrGa$_2$S$_4$ : Eu phosphor are also investigated.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.6
• /
• pp.769-779
• /
• 2007

Statement of problem. When TiN coating is applied to the abutment screw, occurrence of greater preload and prevention of the screw loosening could be expected due to decrease of frictional resistance. However, the proper thickness of TiN coating on abutment screw has not been yet reported. Purpose. The purpose of this study is to find out the appropriate TiN coating thickness by evaluating the detorque force and the surface change of titanium abutment screw with various TiN coating thickness. Material and methods. 1. Material Thirty five non-coated abutment screws were prepared for TiN coating. TiN coatings were prepared by Arc ion plating method. Depending on the coating deposition time(CDT), experimental groups were divided into 6 groups(CDT 30min, 60min, 90min, 120min, 150min, 180min) and those of 1 group was not coated as a control group. Each group was made up of 5 abutment screws. 2. Methods FE-SEM(Field Emission Scanning Electron Microscoper) and EDX(Energy Dispersive X-ray Spectroscopy) were used to observe the surface of the abutment screw. Electric scales was used to measure the weight of the abutment screw after the repeated closing and opening of 10 trials. Detorque force was measured with digital torque gauge, at each trial. Results. 1. As the coating deposition time increased, the surface became more consistent and smooth. 2. As for the abutment screws that were TiN coated for more than 60 minutes, no surface change was found after the repeated closing and opening. 3. The TiN coated abutment screws showed less weight change than the non-coated abutment screws. 4. The TiN coated abutment screws showed higher mean detorque force than the noncoated abutment screws. 5. The abutment screw coated for 60 minutes showed the highest mean detorque force. Conclusion. The coating layer of proper thickness is demanded to obtain consistent and smooth coating surface, resistance to wear, and increased detorque force of the abutment screw. In conclusion, the coating deposition time of 60 minutes indicated improved mechanical property, when TiN coating was conducted on titanium abutment screw.

• Journal of Adhesion and Interface
• /
• v.12 no.4
• /
• pp.144-150
• /
• 2011

The effect of low profile agent and release agent on the surface and mechanical properties of bulk mold compound were investigated. Atomic content and contact angle of surface were characterized using X-ray photoelectron spectroscopy and contact anglemeter. Surface morphology and surface roughness were obtained using field emission scanning electron microscope and atomic force microscope, respectively. As increasing the low profile agent from 0 to 9.2 wt%, the volume shrinkage and surface roughness decreased from 0.35% to 0.05%, and from $0.27{\mu}m$ to $0.12{\mu}m$, respectively. The increase of release agent from 1.8 wt% to 3.6 wt% resulted in the migration of release agent to sample surface and it increased the surface roughness. The flexural strength and impact strength were decreased approximately 30% as the low profile agent increasing from 5.0 wt% to 9.0 wt%.

• Elastomers and Composites
• /
• v.53 no.3
• /
• pp.175-180
• /
• 2018

Solution-styrene-butadiene rubber (SSBR) composites were manufactured using four kinds of fillers: silica-silane coated carbon black (SC-CB) hybrid, starch-SC-CB hybrid, pure silica, and pure starch. The influence of filler type on the mechanical properties of the rubber matrix was studied in this work. SC-CB was prepared by silane-graft-coating using vinyl triethoxy silane and carbon black, which enhanced the dispersion effect between the rubber matrix and the filler, and improved the mechanical properties of the compounds. The morphology of the composites was observed by field-emission scanning electron microscopy (FE-SEM). The thermal decomposition behavior of the composites was determined by thermogravimetric analysis (TGA), and the crosslinking behavior of the composites was tested using a rubber process analyzer (RPA). The hardness, tensile strength, swelling ratio, and gas transmittance rate of the composites were evaluated according to ASTM. The test results revealed that with the addition of SC-CB, the hybrid fillers, especially those blended with silica, showed a better reinforcement effect, the highest hardness and tensile strength, and stable thermal decomposition behavior. This implies that the silica-SC-CB hybrid filler has a notable mechanical reinforcement effect on the SSBR matrix. Because of self-crosslinking during its synthesis, the starch-SC-CB hybrid filler produced the most dense matrix, which improved the anti-gas transmittance property. The composites with the hybrid fillers had better anti-swelling properties as compared to the neat SSBR composite, which was due to the hydrophilicity of silica and starch.

• Journal of Convergence for Information Technology
• /
• v.7 no.4
• /
• pp.75-81
• /
• 2017

The design trend of information technology is quickly changed with the times. The design trend of information display is a bezel-less display, recently. The bezel-less display or edge-less display is a new trend of mobile phone display. In this study, the shading tape was manufactured for assembling process of touch panel display with the high screen-to-body ratio so-called bezel-less display. The shading tape was fabricated on PET film with the UV curable acrylic pressure sensitive adhesive(PSA) by roll-to-roll process. The UV curable PSA was synthesized with the eco-friendly toluene-less manufacturing method. The adhesive power of manufactured shading tape was investigated by motorized tensile testing machine. The thixotropic, maintaining property of cutting shape, was characterized by field emission scanning electron microscope. As results, the shading tape exhibits high adhesive power and good thixotropic performance suitable for assembly process of touch panel display. The functional shading tape will be expected to improve productivity of assembly process of touch panel display.