• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.1361-1368
• /
• 2005

In this paper, the theoretical method of measuring the tunnel convergence and underground displacement, the objective indices of assessing safety for tunnel construction, using the fiber optic sensor is studied by developing the program to automatically measure them. The model test of Con'c beam is conducted to evaluate reliability of the fiber optic sensor. Furthermore, using the RS232 communication protocol as well as Visual C# and Visual C++, the programming tools, the program was developed to detect automatically the measured value of the fiber optic sensor, calculate the tunnel convergence and underground displacement, predict the deformed shape of the tunnel, and evaluate loosening zone due to the tunnel excavation.

• Proceedings of the KIEE Conference
• /
• 1987.11a
• /
• pp.143-146
• /
• 1987

Fiber optics provide a solution to the problems at interference, capacity and reliability in communication. Approximately 20 kilometera of a six-fiber, multimode, longwave($1.3{\mu}m$), graded index silica glass fiber optic cable was helically wrapped around a phase conductor at a Korea Electric Power Corporation(KEPCO) 154KV transmission line. This paper presents an economic comparison of several fiber optic cable installation alternative and discusses the characteristics at the helically wrapped fiber cable, as well as the entire installation, including high voltage phase-to-ground (PTG) end termination, and splicing. The fiber link was installed for the field trial and practical use with overhead composite optical fiber cable which installation performed a few years earlier some other location and is intended to accommodate not only telephone but also supervisory Control and Data Acquisition(SCADA), protective relaying, and telemetry functions.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.14 no.7
• /
• pp.2891-2903
• /
• 2020

Phase-generated carrier (PGC) demodulation algorithm is the main demodulation methods in Fiber-optic interferometric sensors (FOISs). The conventional PGC demodulation algorithms are influenced by the carrier phase delay between the interference signal and the carrier signal. In this paper, an automatic carrier phase delay synchronization (CPDS) algorithm based on orthogonal phase-locked technique is proposed. The proposed algorithm can calculate the carrier phase delay value. Then the carrier phase delay can be compensated by adjusting the initial phase of the fundamental carrier and the second-harmonic carrier. The simulation results demonstrate the influence of the carrier phase delay on the demodulation performance. PGC-Arctan demodulation system based on CPDS algorithm is implemented on SoC. The experimental results show that the proposed algorithm is able to obtain and eliminate the carrier phase delay. In comparison to the conventional demodulation algorithm, the signal-to-noise and distortion ratio (SINAD) of the proposed algorithm increases 55.99dB.

• Proceedings of the Korean Society of Potoscience Conference
• /
• spring
• /
• pp.20-20
• /
• 1998

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.12
• /
• pp.978-982
• /
• 2010

For mass information transfer, the optical communication using optic fiber has been widely used. Especially, in the field of medical image, the large data is digitalized based on the standard image and it is used for telemedicine with this method. Therefore, to transfer the large amount of data fast and effectively POF (Plastic Optical Fiber) can be used and the development of optic connector for connection between POFs is very important. In this study, for stable optical coupling of POF optic fiber Ferrule and Sleeve were designed and produced by considering the bond stability and the insertion loss according to the physical contact and roughness profile was evaluated. As a result of examining the insertion loss by physical contact method of two optic fibers, it showed the loss was about 1.895dB. According to the results from studying the condition of grinding section for POF mass production, the mass production condition was established as POF profile roughness of 6nm and the loss of 0.2dB or lower by controlling the film size and time step by step.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.4 no.1
• /
• pp.7-13
• /
• 2005

In this paper, we propose the time synchronization module on fiber optic repeater to use optic line delay for obtaining time synchronization between up-link and down-link, in the 2.3 GHz WiBro network using TDD/OFDM (Time Division Duplex/Orthogonal Frequency Division Multiplexing) Generally, when we use fiber optic repeater to remove the shade area, it occurs transmission delay which is caused by optic transmission between RAS (Radio Access Station) and fiber optic repeater and inner delay of fiber optic repeater. Because the WiBro system is adopting a TOO method and there exists the difference of switching time which is caused by these delay between up-link and down-link, it occurs ISI (Inter Symbol Interference), ICI (Inter Carrier Interference). These interference results in the reduction of the coverage. And the inconsistency between Up-Link and Down-Link switching time maybe gives rise to the interruption of communication. In order to prevent these cases, we propose synchronization module using analog optic line delay as the one of synchronizing up-link and down-link. And we propose the consideration factor for the designing time synchronization module and the feature of optic line of analog method. The measurement result of optic line time synchronization module of structure proposed is as follows, the delay error of $0.5{\mu}g$ and the insertion loss value below maximum 4.5dB in range of $0{\sim}40{\mu}s$. These results fully meet the specification of WiBro System.

• Proceedings of the IEEK Conference
• /
• 2004.08c
• /
• pp.876-879
• /
• 2004

The buried fiber optic cable as a distributed intrusion sensor for detecting and locating intruders along the long perimeters is proposed. Phase changes resulting from either the pressure of the intruder on the ground immediately above the buried fiber or from seismic disturbances in the vicinity are sensed by a phase-sensitive optical time-domain reflectometer. Light pulses from a Er:fiber cw laser with a narrow, <3kHz-range, spectral width and a frequency drift of < 1 MHz/min are injected into one end of the fiber, and the backscattered light from the fiber is monitored with a photodetector. Results of preliminary studies, measurement of phase changes produced by pressure and seismic disturbances in buried fiber optic cables and simulation of ${\varphi}-OTDR$ response over long fiber paths, to establish the feasibility of the concept are described. The field experiments indicate adequate phase changes, more than 1t-rad, are produced by intruders on foot and vehicle for burial depths in the 0.2 m to 1 m range in sand, clay and fine gravel soils. The simulations predict a range of 10 km with 35 m range resolution and 30 km with 90 m range resolution. This technology could in a cost-effective manner provide enhanced perimeter security.

• Korean Management Science Review
• /
• v.11 no.3
• /
• pp.103-128
• /
• 1994

Due to the trend of evolution toward a broadband communication network with fiber-optics, the design and operation of fiber-optic network have been received a great deal of research attention recently. Furthermore, even a single fiber link failure in the network may result in severe service loss. Thus, the network survivability becomes an importantissue in planning and designing the network. This survey is on modelling of various fiber-optic subscriber loop network(FSLN) design problems, which are essential ones for providing broadband communication services and B-ISDN services. Models are classified and investigated as either conventional decomposition-iteration approach or integrated design method. To build survivable networks, SHR models are also suggested by ring control schemes. The result of this study will be effectively applied to build a design model for FSLN in the practical applications.

• Journal of Communications and Networks
• /
• v.6 no.3
• /
• pp.269-279
• /
• 2004

A new online multi-layer integrated routing (MLIR) scheme that combines IP (electrical) layer routing with WDM (optical) layer routing is investigated. It is a highly efficient and cost-effective routing scheme viable for the next generation integrated optical Internet. A new simplified weighted graph model for the integrated optical Internet consisted of optical routers with multi-granularity optical-electrical hybrid switching capability is firstly proposed. Then, based on the proposed graph model, we develop an online integrated routing scheme called differentiated weighted fair algorithm (DWFA) employing adaptive admission control (routing) strategies with the motivation of service/bandwidth differentiation, which can jointly solve multi-layer routing problem by simply applying the minimal weighted path computation algorithm. The major objective of DWFA is fourfold: 1) Quality of service (QoS) routing for traffic requests with various priorities; 2) blocking fairness for traffic requests with various bandwidth granularities; 3) adaptive routing according to the policy parameters from service provider; 4) lower computational complexity. Simulation results show that DWFA performs better than traditional overlay routing schemes such as optical-first-routing (OFR) and electrical-first-routing (EFR), in terms of traffic blocking ratio, traffic blocking fairness, average traffic logical hop counts, and global network resource utilization. It has been proved that the DWFA is a simple, comprehensive, and practical scheme of integrated routing in optical Internet for service providers.

• IE interfaces
• /
• v.9 no.3
• /
• pp.92-100
• /
• 1996

The current copper-based communication network is going to be replaced with an optic fiber network. The new technology allows a larger amount of information to be transmitted than before. Due to its bandwidth and relatively high installation cost, however, the optic fiber network does not exhibit the inherent structural redundancy provided by the conventional copper-based network. We propose to supply it by adding multiple paths between important nodes. This so-called network survivability problem is computationally expensive to solve exactly. We report the application of a heuristic algorithm to this problem. Also discussed is the issue of how to make use of existing conduits.