• Journal of the Optical Society of Korea
• /
• v.11 no.1
• /
• pp.40-43
• /
• 2007

We propose a taper-underlaid spot-size converter (TU-SSC) with an offset which consists of two vertically stacked taper layers. The designed TU-SSC reduces coupling loss of a high index-contrast waveguide with $1.5%{\Delta}$ to a single mode fiber from 1.5 dB to 0.27 dB. We also considered the effects of mask misalignment in the fabrication process of TU-SSC, and optimized the design of TU-SSC so that the additional loss of TU-SSC for the mask misalignment of $3{\mu}m$ in the photo-lithography process was as low as 0.13 dB.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.16 no.4
• /
• pp.22-26
• /
• 1979

Microlenses with an extremely small radius of curvature are efficiently use d to couple LED/laser diode light into optica1 fiber. We propose a Tapered lens for the highly efficient coupling of the optical fiber communication light souses into the fiber. Ray optical analysis shows that the maximum coupling efficiency is as high as 90 %, Tapered lens with optimum parameters are fabricated by using heating and pulling technique. Experiment shows that this new technique improves the coupling efficiency by two and four times for LED and laser diode, respectively, as compared with the simple flat - end coupling.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.18 no.3
• /
• pp.21-24
• /
• 1981

A simple optial fiber Y-branch is fabricated using micro - torch and fusion splicer. Tapered end of two fibers - in -contact is spliced with another fiber. Total insertion loss is 26dB and optical power branchi ng ratio is 0.98. Using fiber Y-branch, an UTDR with simple optical system is realized The resolution of the OTDR is $\pm$ 5m in length and t 0.5 dB/km in loss coefficient.

• Current Applied Physics
• /
• v.18 no.11
• /
• pp.1441-1446
• /
• 2018

We demonstrate an acousto-optic mode converter based on a tapered optical fiber to efficiently generate orbital angular momentum states of light. In our scheme an acoustic wave is deployed to the waist of tapered optical fiber where two degenerate $HE_{21}$ modes leading to +1 and -1 orbital angular momentum eigen-modes are resonantly excited. The excitation of $TM_{01}$ and $TE_{01}$ modes is suppressed by enlarging the intermodal index difference between near-degenerate spatial modes. Numerical calculation for optimization of the taper diameter is provided. The experimental characterization of generated states is performed by analyzing the output far-field pattern and the spatial interference fringes with a uniform reference beam.

• Journal of Astronomy and Space Sciences
• /
• v.18 no.2
• /
• pp.145-152
• /
• 2001

For the research of solar EUV (extreme ultraviolet) radiation, we have designed a small-sifted engineering model of solar EUV telescope, which is suitable for a Korean satellite. The EUV sole. telescope was designed to observe the sun at $584.3AA$(He I) and $629.7AA$(OV) The optical system is an f/8 Ritchey-Chr rien, and the effective diameter and focal length are 80mm and 640mm, respectively. The He I and 0V filters are loaded in a filter wheel. In the detection part, the MCP (Microchannel Plate) type is Z-stack, and the channel-to-diameter radio is 40:1. MCP and CCD are connected by fiber optic taper. A commercial optical design software is used for the analysis of the optical system design.

• Composites Research
• /
• v.17 no.2
• /
• pp.1-8
• /
• 2004

The present paper is concerned with the optimum design of taper spring, in which the static spring rate of the fiber-reinforcement composite material spring is fitted to that of the steel leaf spring. The thickness and width of springs were selected as design variables. The object functions of the regression model were obtained through the analysis with a common analytic program. After regression coefficients were calculated to get functions of the regression model, optimal solutions were calculated with DOT. E-glass/epoxy and carbon/epoxy were used as fiber reinforcement materials in the design, which were compared and analyzed with the steel leaf spring. The result of the static spring rates show that optimized composite leaf springs agree with steel leaf spring within 1%.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.8 no.2
• /
• pp.90-95
• /
• 2009

All-optical fiber-type gain flattening filer (GFF) for an EDFA (Erbium doped fiber amplifier) were fabricated by using a FBT (fiber biconical tapered) process and the performance of the GFF was tested and athermal package was proposed. Historically, the chief contributor to gain unevenness has been the EDFA. Due to the inherent gain response of the EDFA's operation, there is always a modest imbalance in the gain applied as a function of wavelength. FBT methods have been used to make fiber type couplers and WDM filter since 1980. Attractivity of this methods was simple, cost effective and thermal stability. Simulation program tool is made to design target GFF profile for this paper. Fiber coupler manufacturing machine is modified for the GFF process. The final GFF is obtained by cascading 4 unit filter that has 6 taper stage. Test result shows 1 dB of wavelength flatness in the C band. Polarization dependent loss is under 0.15dB. The center wavelength variation is below ${\pm}$0.35nm at the temperature range of $20^{\circ}C$ to $70^{\circ}C$.

• Korean Journal of Optics and Photonics
• /
• v.4 no.4
• /
• pp.420-427
• /
• 1993

Dielectric thin film mirrors are embedded in multimode and single-mode fibers by a fusion splicing technique. The fibers with $45{\circ}$ angled embedded mirrors serve as ultra-compact directional couplers with low excess optical loss of 0.2 dB for multimode and 0.5 dB for single mode at 1.3 ${\mu}m$ and excellent mechanical properties. The reflectance is wavelength dependent and strongly polarization depencient. Far-field scans of the reflected output power measured with a white-light source show a pattern which is almost circularly symmetric with aspect ratio of 1.09 at 5% of the peak power. The splitting ratio in a multimode coupler measured with a diode laser source is much less dependent on input coupling conditions than in conventional fused biconical-taper couplers, indicating that these couplers are less susceptible to modal noise occuring in optical fiber communication systems. Spectral properties of multilayer internal mirrors normal to the fiber axis have been investigated experimentally, and a matrix analysis has been used to explain the results.

• IEIE Transactions on Smart Processing and Computing
• /
• v.5 no.2
• /
• pp.123-128
• /
• 2016

In this paper, an inversely tapered coupler with Bragg reflectors is reported for the first time. With appropriately positioned reflecting structures, our fiber-to-chip coupler can more efficiently transmit the light from fiber to a waveguide in a photonic integrated circuit (PIC). A numerical simulation evaluated the coupler's efficiency with the reflector. Optimized parameters that maximize the efficiency of the coupler are also investigated. Simulation results show that the reflector with appropriate parameters enhances efficiency by up to 7 dB. Likewise, Bragg metal reflectors implemented by the conventional metallization process can also improve efficiency. It is also shown that the proposed reflector enhances the coupling efficiency in a double-tip taper coupler.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.676-679
• /
• 1997

The present paper is concerned with the optimal deslgn that the static spring rate of the fiber-reinforcement composite spring is fitted to that of the steel leaf spring. The thickness and w~dth of springs were selected as deslgn variables. And object functions of the regression model were obtained through the analysis with a common analytic program. After regression coefficients were calculated to get functions of the regression model, optimal solutions were calculated with DOT. E-GlassIEpoxy and CarbonIEpoxy were used as fiber reinforcement materials in the design, which were compared and analyzed with the steel leaf spring. It was found that the static spring rate of the optimal model was almost similar to that of the existing spring.