• Journal of the Optical Society of Korea
• /
• v.20 no.1
• /
• pp.135-139
• /
• 2016

I propose a vector passive harmonic mode-locked fiber laser based on topological insulator Bi2Se3 interacting with a fiber taper with a diameter of 7 μm. The particles of topological insulator are deposited uniformly onto the fiber taper with light pressure effect. By incorporating the fabricated saturable absorber into an Er-doped fiber laser cavity, stable mode-locked fiber is obtained. Due to the intense evanescent field of the fiber taper, strong confinement of light enhances the nonlinearity of the laser cavity, and passive harmonic mode-locking is performed. I observe a maximum harmonic mode-locking of 356th, corresponding to a frequency of 3.57 GHz. The pulse duration is 824 fs, and the full width at half maximum of the spectrum is about 8.2 nm. The polarization dependent loss of the saturable absorber is ~ 2.5 dB in the wavelength range of the C band. As the cavity contains no other polarization dependent device, the mode-locked laser is functioning in the vector state. The harmonic order vs pump power is investigated. To the best of our knowledge, this report is the highest frequency mode-locked fiber laser based on Bi2Se3. Experimental results indicate that the topological insulator Bi2Se3 functioning with a thin fiber taper is effective for vector harmonic mode-locking.

• Korean Journal of Optics and Photonics
• /
• v.18 no.4
• /
• pp.280-285
• /
• 2007

Based on the multimode fiber taper, a mode size converter for effective optical beam coupling between laser and optical fiber or between the two different optical fibers has been proposed and demonstrated. The device has a multimode input end and a single mode output end. The influence of various parameters, including device structure and launching conditions, on the coupling efficiency has been theoretically analyzed. The theoretical results revealed that the gaussian beam can be coupled into a single mode fiber without considerable insertion loss. The proposed multimode fiber taper has been fabricated using heating and pulling equipment incorporating two micro-torches. Experimental results showed that an optical beam with $50\;{\mu}m$ of large beam size was effectively coupled into single mode fiber through the multimode fiber taper. The insertion loss of the device was 1.3 dB.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.11
• /
• pp.48-53
• /
• 1997

Volume hologram was recorded using reference beam form optical fiber taper. A singel mode fiber was chemically etced to make a taper structure, and we showed experimentally that the referencing by the irregular beam pattern from this taper structure could increase the storage density of photorefractive volume hologram. The spatial selectivity of the volume hologram with this method was increased by two times compared to the normal single mode fiber referencing case. A theoretical analysis with randomly phased plane model also confirmed the results.

• Proceedings of the KIEE Conference
• /
• 1993.11a
• /
• pp.362-364
• /
• 1993

The properties of near-field diffraction by small aperture are investagated and using of optical fiber taper as a small aperture are proposed. Near-field diffracted by aperture smaller than one wave length can overcome the resolution of conventional microscopy and optical component. In this paper production methods of sub-wave length optical fiber taper using solenoid are also proposed.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.10
• /
• pp.98-106
• /
• 1998

Efficient power transmission from a single mode fiber to a thin-film waveguide devices is one of the most fundamental and inevitable subject that should be first solved toward the realization of the integrated optic system. In this paper, fiber-waveguide coupling structure is considered and the large mismatch of field profiles at the fiber-waveguide interface is well avoided by using to the coupling guide which is intentionally developed on the top of the thin-film guuide. From the simulation, the taper-type structure are shown to be easier realizeable than the uniform one, since optical coupling between the guides in the latter has a stronger tolerance to the deviation of waveguide parameters.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.3 no.4
• /
• pp.38-44
• /
• 2012

This paper presents experimental studies aiming at evaluation of structural behaviors of RC (Reinforced Concrete) beams externally strengthened with taper ended CFRPs(Carbon Fiber Reinforced Polymers). Experiments are performed with RC beams having different numbers of CFRP layers and length of each layer. The beams are subjected to four point-bending with simply supported condition. Test results of taper ended CFRPs and non-tapered CFRPs are compared and the better strengthening effect is observed from tapered ended CFRPs.

• Journal of the Optical Society of Korea
• /
• v.13 no.3
• /
• pp.349-353
• /
• 2009

We propose a simple in-line variable optical attenuator (VOA) based on the bending effect of tapered single mode fibers. The influence of the taper structure and the reflective index of the external medium surrounding the taper region on the bending loss of the tapered fiber have been investigated experimentally. An attenuation range exceeding 35 dB and a very low excess loss of < 0.2 dB at 1550 nm were achieved. The measured polarization dependent loss of the present VOA at the attenuation level of 10 dB, 20 dB, and 30 dB were 0.1 dB, 0.2 dB, and 0.5 dB, respectively.

• Journal of Sensor Science and Technology
• /
• v.21 no.2
• /
• pp.151-155
• /
• 2012

We have investigated a refractive index sensor based on a cladded plastic optical fiber taper. The optical transmission and sensing characteristics of the device were illuminated in terms of ray optics. The sensor devices showed that the optical transmittance strongly depends on the refractive index of the external medium surrounding the tapered region.

• Korean Journal of Optics and Photonics
• /
• v.11 no.6
• /
• pp.411-417
• /
• 2000

The waveguide structure effects of a spot-size converter (SSe) of a $1.3\mu{m}$ FP(Fabry-Perot)-LD(Laser Diode) were investigated. Its coupling efficiency and alignment tolerance with a single-mode fiber (SMF) were carefully examined by using a 3dimensional BPM (Beam Propagation Method). It was shown that the fOlmation of enough length of straightened waveguide around the end of the sse region can substantially improve the optical coupling efficiency for a vertically tapered sse. In contrast, a down-taper structure for a laterally tapered sse has superior characteristics to an up-tapered one. We suggested good sse structures which can provide a high coupling efficiency as well as a large alignment tolerance with an .SMF. .SMF.

• Korean Journal of Optics and Photonics
• /
• v.15 no.1
• /
• pp.22-27
• /
• 2004

In this paper, we designed a mode size converter to reduce coupling loss between optical waveguide and single mode fiber. The proposed mode converter is composed of periodically segmented tapered waveguide to achieve small size and easy fabrication. For the optimally designed mode size converter at 1550nm, the taper length is 500(equation omitted), the segmentation period 5ß:, the waveguide width of fiber contact section 1.3ß:, and duty cycle 0.95. The coupling loss of the optimized mode size converter is 0.33㏈/point, which is 1.27㏈/point lower than that without the mode size converter.