• Journal of Power Electronics
• /
• v.14 no.1
• /
• pp.105-114
• /
• 2014

The sliding mode control (SMC) strategy is applied to a permanent magnet synchronous machine vector control system in this study to improve system robustness amid parameter changes and disturbances. In view of the intrinsic chattering of SMC, a current sliding mode control method with a load sliding mode observer is proposed. In this method, a current sliding mode control law based on variable exponent reaching law is deduced to overcome the disadvantage of the regular exponent reaching law being incapable of approaching the origin. A load torque-sliding mode observer with an adaptive switching gain is introduced to observe load disturbance and increase the minimum switching gain with the increase in the range of load disturbance, which intensifies system chattering. The load disturbance observed value is then applied to the output side of the current sliding mode controller as feed-forward compensation. Simulation and experimental results show that the designed method enhances system robustness amid load disturbance and effectively alleviates system chattering.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.5
• /
• pp.211-220
• /
• 2003

The control method of programmable dynamometer for overall test of machine is to load the reference torque which is computed from torque transducer into motor under test. But the torque information detected from torque transducer have a lot of noise when the load torque of meter is a small quantity or changing. Thus, torque transducer must have a low pass filter to detect a definite torque information. But The torque delay generated by filter with torque transducer occur a torque trouble for meter torque of programmable dynamometer. Therefore, this kind of system could not perform dynamic and nonlinear load. In this paper, the control method using the load torque observer without a measure for torque transducer is Proposed. The proposed system improved the problem of the torque measuring delay with torque transducer, and the load torque is estimated by the minimal order state observer based on the torque component of the vector control induction meter. Therefore, the torque controller is not affected by a load torque disturbance. To verify a superiority of the proposed control algorithm, the analysis for a root locus of a conventional control method and the proposed one, and simulation and experiment is performed. Therefore we hope to be extended in industrial application.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.3
• /
• pp.188-195
• /
• 2004

This paper presents neural load torque observer that is used to deadbeat load torque observer and gain compensation by parameter estimator As a result, the response of the PMSM(permanent magnet synchronous motor) follows that nominal plant. The load torque compensation method is composed of a neural deadbeat observer To reduce the noise effect, the post-filter implemented by MA(moving average) process, is adopted. The parameter compensator with RLSM (recursive least square method) parameter estimator is adopted to increase the performance of the load torque observer and main controller The parameter estimator is combined with a high performance neural load torque observer to resolve the problems. The neural network is trained in on-line phases and it is composed by a feed forward recall and error back-propagation training. During the normal operation, the input-output response is sampled and the weighting value is trained multi-times by error back-propagation method at each sample period to accommodate the possible variations in the parameters or load torque. As a result, the proposed control system has a robust and precise system against the load torque and the Parameter variation. A stability and usefulness are verified by computer simulation and experiment.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.8
• /
• pp.1229-1240
• /
• 1997

The purpose of this study is to build up control scheme that promptly control pressure in a hydraulic cylinder having comparatively small control volume, using a PCV (proportional control valve) and a digital computer. Object pressure control system has the character to be unstable easily, because the displacement-flow gain of the PCV is too large considering the small volume of the hydraulic cylinder and the time delay of response of the PCV is comparatively long. Considering the above-mentioned characteristics of the object pressure control system, in this study, control system is designed with two degree of freedom control scheme that is composed by adding a feed-forward control path to I-PDD$^{2}$ control system, and a reference model is used on the decision of control parameters. And through some experiments on the control system with FF-I-PDD$^{2}$ controller, the validity of this control method has been confirmed.

• Journal of Power Electronics
• /
• v.16 no.4
• /
• pp.1355-1366
• /
• 2016

In the present paper, a speed control algorithm with fast response characteristics is proposed to reduce the shift shock of medium/large-sized electric vehicles equipped with a two-speed AMT. Shift shocks, which are closely related with to the vehicles' ride comfort, occur due to the difference between the speed of the motor shaft and the load shaft when the gear is engaged. The proposed speed control method for shift shock reduction can quickly synchronize speeds occurring due to differences in the gear ratios during speed shifts in AMT systems by speed command feed-forward compensation and a state feedback controller. As a result, efficient shift results without any shift shock can be obtained. The proposed speed control method was applied to a 9 m- long medium- sized electric bus to demonstrate the validity through a simulated analysis and experiments.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.4
• /
• pp.386-392
• /
• 2008

This paper presents active vibration control performance of a hybrid mount. The proposed hybrid mount is devised by adopting both piezostack as an active actuator and rubber as a passive element. After experimentally identifying actuating force characteristics of the piezostack and dynamic characteristics of the rubber, the hybrid mount was designed and manufactured. Subsequently, a vibration control system with a specific mass loading is constructed, and its governing equations of motion are derived. In order to actively attenuate vibration transmitted from the base, a feedforward controller is formulated and experimentally realized. Vibration control responses are then evaluated in time and frequency domains.

• Proceedings of the KIEE Conference
• /
• 1999.07c
• /
• pp.1180-1182
• /
• 1999

Modeling for utility interactive photovoltaic power generation system has been studied using PSCAD/EMTDC. The proposed model system consists of a simple utility circuit configuration, 3kW of single phase utility interactive photovoltaic system, single phase PWM voltage source inverter module, and feed forward PID controller as control circuit. In the system, the DC current is assumed constant, and the voltage source inverter provides sinusoidal ac current for the loads of utility system. The simulation results are given in order to verify the effectiveness of the proposed model. The phases of output voltage of utility system and the output current of the inverter module are compared. Especially, the compensation effect of the photovoltaic system for the unbalanced load is analyzed. and the transient phenomena for a phase to ground fault are also simulated.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.38 no.6
• /
• pp.28-36
• /
• 2001

A robust adaptive sliding mode robot control algorithm is derived, which consists of a feed-forward compensation part and discontinuous control part. The unknown parameters is categorized into two groups, with group containing the parameters estimated on-line, and group containing the parameters not estimated on-line. Then a sliding control term is incorporated into the torque input in order to account for the effects of uncertainties on the parameters not estimated on-line and of disturbances. Moreover, the algorithm is computationally simple, due to an effective exploitation of the structure of manipulator dynamics. It is shown that, despite the existence of the parameter uncertainty and external disturbances, the controller is globally asymptotically stable and guarantees zero tracking errors.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.10a
• /
• pp.261-266
• /
• 1995

본 연구에서는 자기부상시스템에 대해 흡인식 자기부상방식을 채택하고 쇠구슬에 대한 운동을 상하 1자유도로 가정하여 운동방정식을 세운다. 이때 전자석이 자기 부상력은 전자석에 흐르는 전류와 인덕턴스의 함수라 가정하고, 모델의 불확실성은 자기부상계의 운동 방정식으로부터 선형화 할 때 발생하는 오차 및 파라미터 변동으로 생각한다. 또한 모델의 불확실성이 존재하더라도 정상편차 없이 부상하는 서보제어계를 설계한다. 그런데 저자등은 강인성 문제 및 정상편차 없는 것에 역점을 두어 H$_{\infty}$ 제어이론에 기초한 1형 로바스트 서보 제어기를 구하여 자기부상 시스템의 안정화 제어계로써 적용한 적이 있다. 이때 중심해 이외의 해를 이용하여 설계한 서보 제어계는 자기부상계의 과도상태시에 일어나는 오버슈트를 줄일 수 없었다. 따라서 시스템 내부 안정화를 위하여 H$_{\infty}$ 제어이론에 의해 설계된 피드백(feedback) 제어기와 물체가 부상할 때 오버슈트를 줄이고 제어량이 목표치에 잘 추종하기 위해 설계된 피드 포워드(feed forward) 제어기로써 2자유도를 갖는 제어계를 설계한다. 이렇게 설계한 2자유도 제어계를 가지고 모의 응답실험과 본 연구자들이 만든 자기부상 시스템의 실험결과를 비교함으로써 설계된 제어기의 타당성을 조사한다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1596-1600
• /
• 2000

We propose a novel adaptive feed forward controller (AFC) design method for rejecting the effect of micro actuator resonance in the design of dual-stage actuator servo systems for disk drives. Microactuator's resonance is one of important issues in dual-stage actuator servo, which varies up to ${\pm}10%$ per product and even during operation. We derive an adaptive algorithm for the proposed AFC design, which turns out to be identical to the delayed-x LMS algorithm which is a special form of the filtered-x LMS algorithm. In the algorithm, coefficients of the AFC are adapted by the residuals of constrained structure defined in such a way that the coefficients become time invariant. Contrary to the conventional AFC, it considers the phase delay of closed-loop transfer function at resonance frequency for system stability. We also apply an adaptive algorithm with frequency tracking capability. The frequency tracking algorithm is induced by the orthogonality of AFC coefficients. Computer simulations are carried out to demonstrate effect of the proposed AFCs.