• 한국기계가공학회지
• /
• 제18권11호
• /
• pp.1-8
• /
• 2019

In this study, we design the feed system and process conditions for a lamp garnish lens of an automobile. For this purpose, four design alternatives are presented and injection molding simulation analyses are performed. The optimal feed system is selected by considering the formability of the product and the cost of mold manufacture. The product formability is assessed by the weld line, warpage, sink mark and the maximum injection pressure, whereas the mold-making cost is estimated by the number of valve gates in the hot runner system. To improve the product formability, process conditions are optimized using an experimental design approach named one-factor-at-a-time. No weld line is generated as a result of the optimization. In addition, it is found the warpage and sink mark are reduced while the maximum injection pressure is increased, compared with those before the optimization.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2006년 제4회 한국유체공학학술대회 논문집
• /
• pp.45-46
• /
• 2006

Usual LEO satellite for earth observation use a blowdown hydrazine monopropellant propulsion system for attitude hold and orbit maintenance. For precision control, thruster valve has very short closing time, but this can cause water hammering and pressure surge. Since water hammering and pressure surge can cause damage of propulsion system and ununiform thrust, Thruster valve closing is one of the special concern during satellite propulsion system design. In this paper, an analysis for propellant feed system is conducted using the method of characteristics. The results represent water hammer effect is negligible even at the worst case and pressure surge can be decreased effectively with a trim orifice.

• 생약학회지
• /
• 제30권3호
• /
• pp.250-254
• /
• 1999

Cadmium chloride and Yukmijihwang-tang extract (YJT), a herbal restorative were treated 3 mg/kg s.c. and 500 mg/kg p.o. respectively, and concurrently to rats, and examined the variations of the body weight, feed efficiency ratio, accumulation of cadmium in kidney, the triglyceride and cholesterol in serum, the blood pressure and heart rate of rats. The values of body weight gained and feed efficiency ratio decreased, and the other values increased significantly in cadmium-treated group, but concurrent administration with YJT showed significant recovery from the toxicity of cadmium.

• 대한환경공학회지
• /
• 제38권9호
• /
• pp.476-481
• /
• 2016

압력지연삼투는 삼투압을 구동력으로 하여 에너지를 생산하는 새로운 막 기술이다. 압력지연삼투는 반투과성 막을 사이에 두고 삼투압으로 인해 저농도의 유입원수가 고농도의 유도용액으로 이동하는 것이다. 본 연구는 역삼투 공정의 농축수를 유도용액으로, 역삼투 공정의 생산수를 유입원수로 하여 8인치 나권형 막모듈의 성능을 평가 하였다. 실험에 사용된 유입원수와 유도용액의 유량은 2.4 L/min, 5.0 L/min, 10.0 L/min, 압력범위는 5 bar에서 30 bar이다. 유입원수와 유도용액의 농도, 유입유량, 유입비에 따른 공정 성능의 영향을 본 연구에서 확인 하였다. 중요 결과로 유도용액의 농도의 증가는 압력지연삼투 공정의 전력밀도, 투과수량을 향상시키는 결과를 보였다. 유입유량의 증가 또한 전력밀도와 투과수량을 향상시키는 결과를 보였다. 또한 최대 전력밀도를 형성하는 유입원수와 유도용액의 최적 유입비는 1:1의 비에서 나타났다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2007년도 제28회 춘계학술대회논문집
• /
• pp.322-325
• /
• 2007

본 논문은 터보펌프를 사용하는 액체로켓의 저압 LOX 공급계의 개발 프로세스를 제공한다. 대한항공은 한국항공우주연구원과 협력하여 터보펌프 공급을 위한 LOX 공급계 개발을 수행하였다. LOX 공급계는 극저온의 온도와 무게절감을 위한 얇은 배관두께가 특징이다. 본 프로젝트의 시스템은 주 배관과 LOX 온도 제어를 위한 재순환 배관으로 구성되어 있다. 각 배관시스템은 벨로우즈, 필터, 오리피스, 밸브류, 플랜지와 서포트로 구성되어 있다. 이 논문에서는 시스템 설계 및 제작, 구조 및 열 해석, 단품 시험에 대하여 설명하였다. 최종적으로, 이 시스템은 한국항공우주연구원의 PTF 시험설비에 조립되어 요구 성능을 달성하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.276-281
• /
• 2001

The KSR-III Main Propulsion System configuration of the liquid oxygen (LOX) feed line is analyzed. This feed line includes a tighter radius and cavitation venturi for flow mass flow-rate passive control. There were concerns that these configurations might generate a great flow distortion at the engine interface. Also both the pressure drop at the feed line and any presence of separation area are a great concern according to the propellant flow. To resolve these issues, a computational fluid dynamic analysis was conducted to determine the flow field in the LOX feed lines.

• 한국자동차공학회논문집
• /
• 제15권2호
• /
• pp.115-125
• /
• 2007

Minimizing the cylinder wear and the consumption rate of cylinder oil in a large two-stroke marine diesel engine is of great economic importance. In Korea, a motor-driven cylinder lubricator for a large two-stroke marine diesel engine manufactured by $W{\ddot{a}}rtsil{\ddot{a}}$ Switzerland Co., Ltd. was first developed by authors through the joint research of industry-university in 2002. The characteristic of the developed product is that can control automatically the oil feed rate to a load fluctuation by the motor drive and the offset cam. The performance of the product is not also inferior to the conventional one. For manufacturing the reliable and useful products, however, it is necessary to investigate further characteristics and improve the performance of a cylinder lubricator. In this study, the effect of quill with and without accumulator on maximum discharge pressure, delivery delay duration and oil feed rate relative to motor revolution speed using plunger stroke as a parameter is experimentally investigated by using the developed cylinder lubricator. It is found that the maximum discharge pressure with accumulator is higher than that of no accumulator as plunger stroke and motor revolution speed are elevated, and the delivery delay duration with accumulator is shorter than that of no accumulator as plunger stroke and motor revolution speed are increased. Also, oil feed rate with accumulator is less than that of no accumulator except for a plunger stroke of 2 mm as plunger stroke and motor revolution speed are raised.

• 한국터널지하공간학회 논문집
• /
• 제17권2호
• /
• pp.141-151
• /
• 2015

터널굴착의 효율성 증진 및 굴착시 발생하는 진동 저감을 위해 연마재 투입형 워터젯 시스템을 이용한 새로운 형태의 암반 굴착 방식이 개발되어 적용 중에 있다. 연마재 투입형 워터젯 시스템을 이용한 암반 굴착 방식에 있어서, 적절한 양의 연마재를 투입하는 것은 절삭 성능뿐만 아니라 전체 공정의 경제성 향상을 위해서도 매우 중요하다. 본 연구에서는, 다양한 공정 변수들 중 터널 굴착용 워터젯 시스템에서 특히 중요한 공정 변수들인 기하학적 변수(연마재 탱크(또는 호퍼) 높이, 연마재 투입관의 구배, 연마재 투입관의 길이, 연마재 투입관의 굴곡도), 연마재 변수(연마재 입자 크기), 젯 에너지 변수(수압, 유량)이 연마재 투입량 및 연마재가 믹싱 챔버 내로 흡입될 때 발생하는 흡입 압력에 미치는 영향을 규명하기 위하여 다양한 조건에서 실험을 수행하고 그 결과를 분석하였다. 또한, 실험적 연구를 통하여 연마재 투입량이 절삭 성능에 미치는 영향을 논의하였다. 본 연구 결과를 바탕으로 주요 공정 변수들을 조절하여 적절한 연마재 투입량을 유지하면 터널 굴착용 워터젯의 절삭 성능을 극대화할 수 있을 것으로 기대된다.

• 한국자동차공학회논문집
• /
• 제22권2호
• /
• pp.123-133
• /
• 2014

Minimizing the cylinder wear and the consumption rate of cylinder oil in a large two-stroke diesel engine is of great economic importance. A motor-driven cylinder lubricator for Sulzer RT-flex large two-stroke diesel engines developed by authors is in need of improving the lubricating system to lubricate cylinder parts optimally by an electronically controlled quill device according to changes of engine load and revolution speed. In order to apply the developed accumulating distributor to an integrated cylinder lubricator by the electronically controlled system as the third research stage, the lubricating system is improved in the electronically controlled quill device with a solenoid valve. In this study, the effects of lubricator revolution speed, driving pressure(or plunger stroke) and cylinder back pressure on oil feed rate and lubrication inequality rate are investigated by using the integrated cylinder lubricator system with an accumulated distribution by the electronic control(I.C.S.), and the oil feed rate and lubrication inequality rate of I.C.S. are compared with those of the motor-driven cylinder lubricator by the electronically controlled quill system equipped with an accumulating distributor(E.D.S.). It is found that the oil feed rate of I.C.S. is smaller than that of E.D.S. due to the reduction of delivery velocity by the higher delivery pressure, and the variances of lubrication inequality rate for I.C.S. have become smaller than those of E.D.S. as the driving pressure in all experimental conditions increases, except for the driving pressure of 26 bar(plunger stroke 2 mm) at the cylinder lubricator speed of 120 rpm.

• 대한의용생체공학회:의공학회지
• /
• 제28권6호
• /
• pp.768-776
• /
• 2007

A new type of the fluid circulation blood pressure simulator was proposed to enhance the blood pressure simulator used for the development and evaluation of automatic sphygmomanometers. Various pressure waveform of fluid flowing in the pipe was reproduced by operating the proportional control valve after applying a pressure on the fluid in pressurized oil tank. After that, appropriate fluid was supplied by operating the proportional control valve, which enabled to reproduce various pressure wave of the fluid flowing in the tube. To accomplish this work, the mathematical model was carefully reviewed in cooperating with the proposed simulator. After modeling the driving signal as input signal and the pressure in internal tube as output signal, the simulation on system parameters such as internal volume, cross-section of orifice and supply pressure, which are sensitive to dynamic characteristic of system, was accomplished. System parameters affecting the dynamic characteristic were analyzed in the frequency bandwidth and also reflected to the design of the plant. The performance evaluator of fluid dynamic characteristic using proportional control signal was fabricated on the basis of obtained simulation result. An experimental apparatus was set-up and measurements on the dynamic characteristic, nonlinearity, and rising and falling response was carried out to verify the characteristic of the fluid dynamic model. Controller was designed and thereafter, simulation was performed to control the output signal with respect to the reference input in the fluid dynamic model using the proposed proportional control valve. Hybrid controller combined with an proportional controller and feed-forward controller was fabricated after applying a disturbance observer to the control plant. Comparison of the simulations between the conventional proportional controller and the proposed hybrid simulator indicated that even though the former showed good control performance.