• 한국정보통신학회논문지
• /
• 제7권5호
• /
• pp.1026-1031
• /
• 2003

자동 급수펌프는 압력스위치에 의해 운전 및 정지를 하게 된다. 따라서 수량 증감에 따른 펌프의 빈번한 운전 및 정지로 인해 지속적인 정격 및 정압 운전이 불가능하다. 또한 빈번한 작동으로 인해 지속적으로 일정한 압력을 얻을 수 없으며, 펌프의 소손과 에너지의 낭비가 심한 단점을 가지고 있다. 본 논문에서는 이러한 단점을 해결하고자 급수밸브, 유량센서, 제어장치로 구성되는 정압 급수장치를 설계 제작하였다. 급수밸브는 유출되는 물의 양과 관계없이 항상 일정한 양의 물을 유입하여 펌프의 부하를 줄이는 역할을 한다. 유량센서는 적외선 다이오드를 사용하여 유출되는 물의 양의 측정하며, 제어장치는 8 비트 마이크로프로세서를 이용하여 설계하였으며, 특별한 제어 알고리듬에 의해 펌프의 운전과 정지를 제어하게 하였다. 본 논문에서 개발한 장치는 토출 압력이 일정하게 유지되고 펌프의 작동 및 정지 동작이 부드럽게 이루어지며, 펌프의 지속적인 정압운전이 가능하므로 기존의 단점을 보완하는 장치로 사료된다.

• Journal of Welding and Joining
• /
• 제22권1호
• /
• pp.71-76
• /
• 2004

In the standpoint of the arc pressure, the effects of the filler wire feed rate on the penetration was investigated in this study. The pure Ar gas was used as a shield gas and the parameters investigated were the welding current and the filler wire feed rate. By making the experiment on the arc pressure, we could know that the arc pressure was fluctuated as the depth-into-arc of the tungsten rod. Instead of the filler wire, the tungsten rod was supplied into the molten pool to make this experiment. Because the filler wire melted in arc and then we couldn't measure the arc pressure. So, the tungsten rod - the highest melting point - was used. According to the depth-into-arc of the tungsten rod, the arc pressure could be measured by using the manometer. It was proved that the arc pressure got higher as the wire feed rate was slow. It is reported the arc pressure is proportion to welding voltage and the square of welding current. But, in the filler wire TIG welding, we could blow that arc pressure was fluctuated as the depth-into-arc of filler wire was changed. We could measure the arc pressure by the variation of the filler wire feed rate and could verify that it affected bead shape and penetration.

• 플랜트 저널
• /
• 제13권3호
• /
• pp.26-29
• /
• 2017

본 연구에서는 메탄올-아세톤 압력 변환 증류 공정에서 유입 흐름의 조성 최적화를 진행하였다. 압력 변환 증류 공정에서 유입 흐름의 조성은 혼합물 분리가능성에 지대한 영향을 주는 것이 잘 알려져 있다. 분리된 순수한 물질의 환류흐름을 이용하여 유입 흐름의 조성을 조절하여 정해진 압력에서 보다 나은 분리효율을 보이는 것을 이번 연구의 목적으로 한다. 환류 흐름이 없는 압력 변환 증류 공정을 기본 공정으로 하여, 메탄올의 환류 흐름이 있는 경우와 아세톤의 환류 흐름이 있는 경우 두 가지 공정이 설계되었다. 각 공정은 Total annual cost로 비교되었으며, 그 결과 환류 흐름이 없는 기본 공정이 가장 유리한 것으로 나타났다.

• 한국항공우주학회지
• /
• 제30권1호
• /
• pp.88-94
• /
• 2002

고압의 불활성 기체를 이용하여 엔진에 추진제를 공급하는 액체로켓의 경우, 추진제 탱크의 압력은 정상연소상태의 연소압을 기준으로 하여 설계한다. 그러나 연소초기의 연소실 압력은 대기압 상태이므로 과도한 유량이 공급되어 이로 인해 hard-start가 발생하며, 최악의 경우 엔진의 파손을 가져온다. 본 연구에서는 이러한 문제를 해결하고 안정된 연소를 위하여 개선된 추진제 공급시스템을 제안하며, 이는 실제 연소실험을 통해 그 성능을 규명 하였다. 이 공습시스템은 연소 초기 및 연소 중의 일정한 유량공급을 위해 Cavitating Venturi를 사용하는 시스템이다. Cavitating Venturi는 오직 공급압력에 의해서만 유량이 결정되며, 출구압력에 영향을 받지 않으므로 연소 초기는 물론이고, 연소 중 이상 연소에 의해 연소압이 떨어져도 설계치 이상의 유량이 공급되지 않는다. 본 실험을 통해서 Cavitating Venturi의 설계 영역에서의 유량에 대한 안정성이 입증되었기 때문에, Cavitating Venturi는 액체로켓 이외의 압력강하량 변화가 큰 시스템에서 매우 효과적일 것이다.

• Journal of Biosystems Engineering
• /
• 제1권1호
• /
• pp.15-15
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic?iency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet?ween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr?ease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$$$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea?ses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin?ear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num?ber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco?very rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• Journal of Biosystems Engineering
• /
• 제1권1호
• /
• pp.17-48
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic\ulcorneriency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet\ulcornerween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr\ulcornerease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$ $$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$ The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$ These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea\ulcornerses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin\ulcornerear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num\ulcornerber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco\ulcornervery rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• 멤브레인
• /
• 제13권4호
• /
• pp.257-267
• /
• 2003

반응성 페놀수지 폐액을 처리하기 위해 중공사막 모듈을 이용한 투과증발 막 탈수공정을 연구하였다. 이 공정의 거동을 예측하기 위한 모사모델을 확립하였고 여기에 사용되는 중요 기본 파라메타들을 평판형 막을 사용하여 직접 구하여 사용함으로써 공정모사의 정확성을 얻을 수가 있었다. 이들을 모사치와 중공사 투과증발 막으로 부터 직접 측정한 각 투과특성들을 비교한 결과 서로 잘 일치함을 보여 본 모사모델의 타당성을 입증하였다. 사용된 중공사막은 중공사 안쪽에 활성층이 도포되어 있으며 공급액은 중공사 내부로 공급하였다. 공급액의 막내에서의 흐름속도에 따라 온도분포가 결정되며 이에 따라 막 투과특성이 달라짐을 모사결과로부터 얻을 수가 있었다. 공급액 온도증가는 막을 통한 탈수 투과 속도를 증가시킬 뿐 아니라 반응속도 증가로 인하여 물 생성속도도 증가시킴으로써 공급액 저장조 내의 수분 함량은 이들 상반된 공정들에 의해 결정이 됨을 보였다. 투과압력이 공급액 증기압보다 훨씬 작은 범위에서 증가할 경우 투과추진력인 공급액과 투과부의 투과물 활성도비 감소가 크지 않아 투과특성을 약간 저하시킨다. 그러나 투과압력이 공급액의 증기압에 접근할 경우 활성도비 감소가 현저하게 일어나 투과특성저하가 급격히 일어난다.

• 한국수산과학회지
• /
• 제52권3호
• /
• pp.247-255
• /
• 2019

This study was conducted to investigate the effects of extrusion pressure and particle size of feed ingredients on the growth performance and plasma hormone activity in juvenile olive flounder Paralichthys olivaceus. Experimental diets were prepared with extrusion pressure manipulated by screw speed [low pressure (LP), 885 rpm/min; high pressure (HP), 708 rpm/min] and different dietary particle sizes [specific surface area: small (SS), $169.9m^2/kg$; large (LS), $67.4m^2/kg$] in a two-level factorial design. Four experimental diets (LP+SS, LP+LS, HP+SS, and HP+LS) were randomly assigned to 12 tanks (3 replicates) stocked with 20 fish (initial weight, 57 g) per tank. After a 4-week feeding trial, the observable trends of the main effects of extrusion pressure and particle size on growth performance showed that LP and SS enhanced fish weight gain. The plasma insulin-like growth factor-I level was significantly higher in fish fed the LP+SS diet than in fish fed the HP+SS diet. These results indicate that manipulation of the physical qualities of feed through adjustment of extrusion pressure and feed ingredient particle size may influence the growth performance of juvenile olive flounder, which should be considered in feed manufacture.

• 한국유체기계학회 논문집
• /
• 제19권3호
• /
• pp.10-13
• /
• 2016

The wet-air oxidation in gravity pressure reactor is effective for organic waste treatment with energy saving under high pressure and high temperature. But its oxidation control is difficulty because its multi-phase flow characteristics is very complicated. The flow characteristics of an oxidizer feed section in the gravity pressure reactor were investigated using numerical method which are verified by comparison with experimental results. In this study, the results showed that the flow rate of oxidizer have an effect on the generation of bubble around feed section.

• 한국추진공학회지
• /
• 제4권2호
• /
• pp.6-11
• /
• 2000

고압의 불활성 기체를 이용하여 엔진에 추진제를 공급하는 액체로켓의 경우, 추진제 탱크의 압력은 정상연소상태의 연소압을 기준으로 하여 설계한다. 그러나 연소초기의 연소실 압력은 대기압 상태이므로 과도한 유량이 공급되어 이로 인해 hard-start가 발생하며, 최악의 경우 엔진의 파손을 가져온다. 본 연구에서는 이러한 문제를 해결하고 안정된 연소를 위하여 개선된 추진제 공급시스템을 제안하며, 이는 실제 연소실험을 통해 그 성능을 규명하였다. 이 공급시스템은 연소초기의 급격한 연소실압의 상승을 막기 위하여 추진제를 예연소단계와 주연소단계의 2단계로 공급하며, 연소초기 및 연소 중의 일정한 유량공급을 위해 Cavitating Venturi를 사용하는 시스템이다. 설계 유량보다 적은 양의 추진제를 먼저 공급하여 연소압이 일정수준에 달하도록 예연소압을 형성하게 하는 방법이다. 또한, Cavitating Venturi는 오직 공급압에 의해서만 유량이 결정되며, 출구 압에 영향을 받지 않으므로 연소초기는 물론이고, 연소 중 이상연소에 의해 연소압이 떨어져도 설계치 이상의 유량이 공급되지 않는다.