• Journal of Satellite, Information and Communications
• /
• v.10 no.3
• /
• pp.109-113
• /
• 2015

This paper presents the study results on a dual band feed horn for the focused reflector. A coaxial waveguide structure is attractive to avoid blockage from the feeder. The inner conductor as a hollow waveguide is designed to excite TE11 of a circular waveguide for high frequency. For low frequency, the design of the outer coaxial waveguide that propagates coaxial TE11 and prevents fundamental TEM is presented. The horn size for generation of these modes results in the degradation of performance. The return loss is improved by a capacitive iris and an inductive iris The enhanced pattern symmetry by dual mode is presented. The horn design in this paper are verified through the test.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.1
• /
• pp.87-94
• /
• 2008

This paper proposes a high-gain monopulse antenna using the folded reflectarray for a monopulse target-tracking radar systems designed at the center frequency of 94 GHz. In target-tracking radar systems, the angle of arrival of the incoming wave Is determined by comparing the signal received on two or more non-coincident antenna patterns. This is the physical basis of most target-tracking techniques and the comparison is made simultaneously in a monopulse radar systems. In this paper, the antenna consists of polarizing grid, reflectarray, multimode feed horn, and comparator implemented by wavguide. The antenna is able to have three radiation patterns by using the monopulse feed systems assembled by multimode feed horn and comparator. The antenna demonstrates maximum gains 36dB, 33.5dB and 27.2dB at sum mode, azimuth mode, and evevation mode respectively.

• The Bulletin of The Korean Astronomical Society
• /
• v.43 no.2
• /
• pp.44.2-44.2
• /
• 2018

We conducted efficiency calculation in a prototype receiver optics for ASTE 10 meter telescope using the measured beam patterns of the band7+8 feed horn. Beam measurements results are summarized and estimated aperture efficiencies over band7+8 frequency range are presented.

• The Bulletin of The Korean Astronomical Society
• /
• v.42 no.2
• /
• pp.57.3-58
• /
• 2017

We report the detailed design of an unprecedented wideband(band7+8) corrugated feed horn in ASTE focal plane array aiming for future ALMA receiver. We have found that such design constraints as return loss, cross-polarization level, beam width and phase curvature can be controlled by optimizing critical corrugation parameters at the throat and flare region of the horn. The success of optimization manifest itself through simulated aperture effciency over 80 % at the entire frequency range. Physical implications of the resulting corrugation parameters are discussed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.4
• /
• pp.619-626
• /
• 2000

The electromagnetic fields of the corrugated annular feed-horn antenna have been analyzed exactly by using the finite-difference time-domain (FDTD) technique. The radiation pattern and return loss characteristics of the antenna were obtained as a function of the impedance of feeding coaxial line at 11.8GHz. The return loss was determined to be less than -25dB at 30$\Omega$. It was confirmed that the phase error is less compared to that of the antenna without corrugation, but the directivity of the radiation pattern needs to be improved.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.487-491
• /
• 2003

Design procedure of corrugated horn antenna for mm-wave frequency range is presented, and hybrid condition in horn is calculated. Balanced hybrid mode should be converted in the horn from TE11 mode by the proper corrugation dimensions which size are available to be fabricated under the mm-wave short wavelength condition. In this paper, corrugate profiles which satisfy both hybrid condition and fabrication possibility are obtained.. By cylindrical mode theory, the electromagnetic fields both inside hem and corrugation are delivered. Propagation characteristics in hem is calculated by the mode impedance matching method with boundary conditions, and radiation fields are obtained by the Kirchhoff-Hyugen principle to the hem aperture fields. A mm-wave corrugated horn operates on 85 - 115GHz is designed and fabricated, and results of measurement are also shown.

• Journal of IKEEE
• /
• v.26 no.1
• /
• pp.137-140
• /
• 2022

In this paper, we proposed a new W-band monopulse tracking system based on reflectarray antenna structure. The proposed reflectarray antenna monopulse tracking system consists of four feed horn antennas and a planar reflector using a microstrip reflectarray. The four feed horn antennas have a gain of 10 dBi and a half-power beam-width of 56 degrees symmetrically in the E/H plane. It was confirmed that the reflectarray antenna using one feed horn antenna has a size of 41.8 × 41.8 mm², a gain of 26.8 dBi, and a half-power beam-width of about 5.6 degrees. The reflectarray monopulse tracking system using 4 feeding horn antennas is well matched from 75 GHz to 90 GHz, and the isolation is secured by more than 10 dB. Finally, the proposed system shows the tracking range of 5.98 degrees and the tracking error range was 0.02 degrees.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.68 no.1
• /
• pp.77-82
• /
• 2019

In this paper, a 0.6~6GHz quad-ridge horn antenna which can be used for the antenna measurement of 5.8GHz WiFi system from lowest frequency band of mobile LTE (Long Term Evolution) is designed and implemented. The quad-ridge horn antenna has quadruple ridges of exponential function, a back-short and a cavity. Based on this structure, we design the cavity size, ridge gap and feed gap to have broadband characteristics. For implementation, the plates material of aluminum and copper are used for the horn and four ridges, respectively. And the insulator supports are used to maintain the gap between ridges. By measurement, antenna has the gain of 6.2~13.35dBi with the return loss of less than -6dB (under VSWR 3 : 1) in the entire design band. The results of this study can be widely used to the antenna studies on the mobile communication including low frequency band of LTE, the EMI measurement and the standard calibration measurement.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.6
• /
• pp.640-646
• /
• 2008

Design procedure of corrugated horn antenna for the mm-wave frequency range is presented, and hybrid condition in horn is calculated. In this paper, corrugate profiles of horn which satisfy both transition to balanced hybrid condition and fabrication possibility under the mm-wave short wavelength are obtained. Electromagnetic fields inside horn and corrugation are derived by the cylindrical mode theory. Propagation characteristics in the horn are calculated by the mode impedance matching method with boundary conditions, and radiation fields are obtained by the Kirchhoff-Hyugen principle to the horn aperture fields. A mm-wave corrugated horn antenna which operates on $85{\sim}115GHz$ is fabricated by electric forming method. Measurements show that VSWR is under 1.3:1 over whole band and the half power beamwidth on radiation pattern 9.2, 9.16 and 9.02 degree on 85, 100 and 110 GHz are agree well with theoretical calculation.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.3
• /
• pp.515-522
• /
• 1994

The radiation characteristics of the conical corrugated feed horn are analyzed by the Gaussian beam mode theory. the electric field over the aperture can be expanded in terms of a set of Gaussian-Laguerre modes. It is proved that these modes are the solutions of the wave epuations for the paraxial approximation. A method, using the sum of the mode expansion coefficients instead of calculation only the fundamental mode, is presented in order to reduce the radiation pattern error. For illustrative examples, the radiation patterns of the corrugated horn antenna operting over C, Ku, and mm-wave band are calculated. Our results agree well with the results obtained by the vector potential method over each band, and also agree well with the measured value at 6.175GHz.