• 청정기술
• /
• 제19권4호
• /
• pp.416-422
• /
• 2013

본 연구에서는 환경친화적인 측면을 고려하여 제철소 및 석유화학공장에서 많이 발생되는 부생가스인 일산화탄소와 산소를 이용하여 글리세롤로부터 글리세롤 카보네이트를 합성하는 공정에 대하여 연구하였다. 글리세롤의 산화성 카르보닐화 반응활성은 회분식 고압반응기에서 다양한 금속촉매(Cu, Pd, Fe, Sn, Zn, Cr계)에 대한 영향과 산화제, 일산화탄소와 산소의 몰 비율, 촉매량, 용매의 종류, 반응 온도 및 시간, 탈수제 첨가에 대한 반응조건들을 확인하였다. 특히, 염화구리 촉매가 우수한 반응 활성을 나타내었고, 니트로벤젠 용매상에서 글리세롤:일산화탄소:촉매의 몰 비율이 1:3:0.15, 일산화탄소:산소의 몰 비율이 2:1, 전체 반응압력이 30 bar, 반응온도 413 K, 반응시간 4시간 동안 염화구리(I)와 염화구리(II) 촉매에 대한 수율은 각각 최대 44%와 64%를 보였다. 이러한 결과로부터 구리촉매의 산화수에 따라 반응활성이 큰 차이가 보이는 것을 확인하였으며, 산화제로서의 산소의 역할은 글리세롤의 카르보닐화 반응 후 산화반응이 수반되어 부생성물인 물을 생성하는데 중요한 역할을 하고 있는 것을 확인할 수 있었다.

• 청정기술
• /
• 제25권1호
• /
• pp.14-18
• /
• 2019

여러 금속 부품을 가공하기 위하여 사용된 염화제이철 에칭 폐액은 유가금속인 니켈 등을 함유하고 있다. 본 연구에서는 식각공정을 완료한 에칭폐액을 재생하고 부산물로 나온 니켈 함유 폐액으로부터 정제하여 니켈 금속분말로 제조하는 공정을 개발하였다. 부산물인 니켈함유용액을 철 등의 불순물을 침전 제거하기 위하여 수산화나트륨 수용액을 실험을 통하여 가수분해 중화제로서 선정하였고, 이를 통하여 철 등의 불순물을 pH = 4 조건하에 침전 제거하였다. 그 후, 불순물로 잔류하는 망간 및 아연과 같은 금속이온들을 D2EHPA (Di-(2-ethylhexyl) phosphoric acid)를 사용하여 용매추출 하였다. 정제된 염화니켈은 99% 이상의 순도를 가지고 있으며, 그 후 환원제로 하이드라진을 이용하여 99% 이상의 순도와 약 150 nm의 크기를 가지는 니켈 금속분말로 제조하였다. 염화니켈 및 니켈 금속분말의 성분은 EDTA 적정법과 유도결합 플라즈마 방출분광법(inductively coupled plasma optical emission spectrometer, ICP-OES)을 이용하여 확인하였으며, 전계방사 주사전자현미경(field emission scanning electron microscope, FE-SEM), X-선 회절분석기(X-ray diffraction, XRD) 및 투과전자현미경(transmission electron microscopy, TEM)을 통하여 금속분말의 형태, 입자 크기 및 결정성과 같은 물리적 특성을 확인하였다.

• Journal of the korean society of oceanography
• /
• 제34권2호
• /
• pp.122-131
• /
• 1999

This study examined the relationship between the sediment pollution and the occurrence of polychaetes in a heavily polluted saltwater lake, Lake Shihwa on the west coast of Korea, separated from the sea by a dike in 1994. The species composition of polychaete assemblage was compared with that found off the lake in Kyeonggi Bay. Environmental variables investigated both in and off the lake were the grain size distribution, chemical oxygen demand(COD) and metal concentrations (Al, Fe, Mn, V, Co, As, Pb, Cr and Cu) in the sediment. We sampled sediments at 10 stations in the lake and 25 stations in Kyeonggi Bay using a modified van Veen grab. The levels of COD, chromium, and copper in sediments were much higher in Lake Shihwa than in Kyeonggi Bay. Differences in the species composition were found along the pollution gradient. An azoic zone was observed in the most heavily polluted area at the upper reach of the lake and the Polydora ligni zone in the center of the lake. Bottom fauna were diverse in Kyeonggi Bay; however, Heteromastus filiformis predominated in the organically enriched sediment. The density of dominant species differed along the pollution gradient. The highest density or H. filiformis was round at the COD level or around 5.8 mg/g. The COD level in the sediment where P. ligni predominated was tow-fold higher than that where H. filiformis occurred in large numbers. The chromium and copper contents at which P. ligni showed a maximum abundance were 120 mg/kg and 127 mg/kg, respectively. The density of H. filiformis was highest at concentrations of 56 mg/kg chromium and 13 mg/kg copper.

• 한국주조공학회지
• /
• 제20권5호
• /
• pp.323-329
• /
• 2000

The HSS consists of hard carbide and matrix of martensite, and so its characteristics of wear resistance, fracture resistance, and surface roughness are good. This study was undertaken to investigate the influence of Nb and V and manufacturing conditions on microstructural behaviors and characteristics in the HSS cylindrical specimens(90 $mm^{O.D.}$ ${\times}$ 60 $mm^{I.D.}$ ${\times}$ 50 $mm^H$) manufactured using VCC(Vertical Centrifugal Casting). In the specimen of Fe-2C-6Cr-1.5W-3Mo-4V alloy, the amount of MC carbide was increased and $M_7C_3$ carbide was decreased with the increase of V and Nb contents. The primary VC carbide was formed and followed by the rod-type eutectic MC carbide was formed in the cell boundary in 9%V added specimen. MC carbide was increased, and $M_7C_3$ carbide was decreased with the addition of Nb content. In the specimen containing more than 3%Nb, primary NbC carbide was formed within the cell of matrix. With increase in rpm, cell and carbides became fine, and amount of carbide $M_7C_3$ was decreased due to increase in cooling rate.

• 한국대기환경학회지
• /
• 제25권2호
• /
• pp.108-121
• /
• 2009

The suspended particulate matters have been collected on membrane filters and glass fiber filters by an 8-stage cascade impactor for 2 years (Sep. 2005${\sim}$Sep. 2007) in Kyung Hee University-Global Campus located on the border of Yongin and Suwon. The 20 chemical species (Al, Mn, Si, Fe, Cu, Pb, Cr, Ni, V, Cd, Ba, $Na^+$, ${NH_4}^+$, $K^+$, $Mg^{2+}$, $Ca^{2+}$, $Cl^-$, ${NO_3}^-$, and ${SO_4}^{2-}$) were analyzed by an ICP-AES and an IC after performing proper pre-treatments of each sample filter. Based on these chemical information, the PMF receptor model was applied to identify the source of ambient size-by-size particulate matters. The receptor modeling is the one of the statistical methods to achieve resonable air pollution management strategies. A total of 10 sources was identified in 9 size-ranges such as long-range transport, secondary aerosol, $NH_{4}NO_{3}$ related source, coal combustion, sea-salt, soil, oil combustion, auto emission, incineration, and biomass burning. Especially, the secondary aerosol source assorted in fine and coarse modes was intensively studied.

• 한국환경과학회지
• /
• 제17권10호
• /
• pp.1147-1154
• /
• 2008

Road runoff, one of non-point source pollutants, contains various heavy metals, most of which flow into discharge waters without being treated. The mechanism of removing the heavy metals in water is similar to that of removing micro-particles. Therefore, it is considered that it is possible to remove a lot of the heavy metals contained in the road runoff by filtering or absorbing them. In this paper, performed has been a basic study on the characteristics of UNFS (Up Flow Non-Point Source Filtering System) using carbide pellet and zeolite pellet as double-layer filtering mediums to treat the road runoff. The removal rate with filtering and absorption time has been shown as follows: 29.0% for Cr; 27.8% for Cd; 25.7% for Fe; 25.4% for Co; 21.2% for Pb; ]9.6% for Zn; 18.2% for Al; 17.0% for Mn; 11.3% for Ni; 7.5% for Cu. The overall removal rate according to influx change has been shown to be approximately 30%, and the load of heavy metals flowing out in initial precipitation could be reduced by using carbide as a recycling filtering medium. When the removal as coarse particles settle is added up, it is expected that UNFS will result in a higher removal rate.

• 열처리공학회지
• /
• 제11권2호
• /
• pp.140-149
• /
• 1998

The graphitization is affected by the addition of small amount of the elements, such as Si, Al, Ni, B, Cr and Mn etc. Boron is well known as the most effective element for the graphitization of cementite in high carbon steels. But a study on quantitative analysis of B effect on the graphitization is few reported. Therefore the effect of boron addition in Fe-0.65%C-1.0%Si-0.5%Mn steels on the graphitization is investigated quantitatively using hardness tester, optical microscope and scanning electron microscope, neutron induced microscopic radiography. The graphitization in high carbon steels is promoted with 0.003~0.005%B addition. But the graphitization in steels which has no boron takes long holding time at $680{\sim}720^{\circ}C$. The hardness of quenched steel containing 0.003%B is higher than that of 0.005%B added steel due to complete dissolution of fine graphites into the austenite. The 0.003%B added high carbon steel graphitized at $680^{\circ}C$ for 25hr is useful steel for the agricultural implements and automobile parts which needed a good formability and high hardness.

• Bulletin of the Korean Chemical Society
• /
• 제25권4호
• /
• pp.511-516
• /
• 2004

A Li$[Co_{0.17}Li_{0.28}Mn_{0.55}]O_2$ cathode compound was prepared by a simple combustion method. The X-ray diffraction pattern showed that this compound could be classified as ${\alpha} -NaFeO_2$ structure type with the lattice constants of a = 2.8405(9) ${\AA}$ and c = 14.228(4) ${\AA}$. According to XANES analysis, the oxidation state of Mn and Co ions in the compound were 4+ and 3+, respectively. During the first charge process, the irreversible voltage plateau at around 4.65 V was observed. The similar voltage-plateau was observed in the initial charge profile of other solid solution series between $Li_2MnO_3\;and\;LiMnO_2$ (M=Ni, Cr...). The first discharge capacity was 187 mAh/g and the second discharge capacity increased to 204 mAh/g. As the increase of cycling number, one smooth discharge profile was converted to two distinct sub-plateaus and the discharge capacity was slowly decreased. From the Co and Mn K-edge XANES spectra measured at different cyclic process, it can be concluded that irreversible transformation of phase is occurred during continuous cycling process.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.393-393
• /
• 2016

Cu(In,Ga)Se2 (CIGS) 박막 태양전지는 높은 효율과 낮은 제조비용, 높은 신뢰성으로 인해 박막 태양전지 중 가장 각광받고 있다. 특히 유리기판 대신 가볍고 유연한 철강소재나 플라스틱 소재를 이용하여 발전분야 외에 건물일체형, 수송용, 휴대용등 다양한 분야에 적용이 가능하다. 이러한 유연 기판을 이용한 CIGS 태양전지의 개발을 위해서는 기판의 특성에 따른 다양한 공정개발이 선행되어야 한다. Stainless steel과 같은 철강기판의 경우 Fe, Ni, Cr등의 불순물이 확산되어 흡수층의 특성을 저하시켜 효율을 감소시킨다. 따라서 이러한 철강 기판의 경우 불순물의 확산을 방지하는 확산방지막이 필수적이다. 이러한 유연기판의 특성을 고려하여 본 연구에서는 기존의 두껍고 추가 장비가 요구되는 SiOx나 Al2O3 대신 200nm 이하의 ZnO 박막을 이용하여 확산방지막을 제조하였다. 유연기판으로 STS 430 stainless steel을 이용하였다. 먼저 stainless steel 기판을 이용하여 기판에 의한 흡수층의 특성을 분석하였으며 ZnO 확산 방지막의 유무 및 두께에 따른 흡수층 및 소자의 특성을 분석하였다. 이때 확산 방지막은 기존 TCO 공정에서 사용되는 i-ZnO를 사용하였으며 RF sputter를 이용하여 50~200nm로 두께를 달리하며 특성 비교를 실시하였다. 효율은 확산방지막을 적용하지 않았을 때 약 5.9%에서 확산 방지막 적용시 약 10.7%로 증가하였다. 그 후 기판으로부터 확산되는 불순물의 유입에 의한 결함을 분석하기 위해 DLTS를 이용하여 소자 특성을 분석하였다. 온도는 80~300K으로 가변하며 측정을 실시하였으며 그 후 계산을 통해 activation energy와 capture cross section 값을 구하였다. DLTS 분석 결과 Ni이 CIGS 흡수층으로 확산되어 NiCu anti-site를 형성하여 태양전지의 효율을 감소시키는 것을 확인하였다. 모든 흡수층은 Co-Evaporation 방법을 이용하여 제조하였으며 제조된 흡수층은 SEM, XRF, XRD, GD-OES, PL, Raman등을 이용하여 분석하였으며 그 외 일반적인 방법을 이용하여 Mo, CdS, TCO, Al grid를 제조하였다. AR 코팅은 제외 하였으며 제조된 소자는 솔라 시뮬레이터를 이용하여 효율 특성 분석을 실시하였으며 Q.E. 분석을 실시하였다.

• Membrane and Water Treatment
• /
• 제9권6호
• /
• pp.463-471
• /
• 2018

The present paper deals with the liquid-liquid extraction and flat sheet supported liquid membrane studies of Pd(II) separation from nitric acid medium using a novel synthesized ligand, namely, N,N,N',N'-tetraethyl-2,2-thiodiethanthiodiglycolamide (TETEDGA). The effect of various diluents and stripping reagents on the extraction of Pd(II) was studied. The liquid-liquid extraction studies showed complete extraction of Pd(II) in ~ 5 min. The influence of nitric acid and TETEDGA concentration on the distribution of Pd(II) has been investigated. The increase in nitric acid concentration resulted in increase in extraction of Pd(II). Stoichiometry of the extracted species was found to be $Pd(NO_3)_2{\cdot}TETEDGA$ by slope analysis method. Extraction studies with SSCD solution showed negligible uptake of Pt, Cr, Ni, and Fe, thus showing very high selectivity and extractability of TETEDGA for Pd(II). The flat sheet supported liquid membrane studies showed quantitative transport of Pd(II), ~99%, from the feed ($3M\;HNO_3$) to the strippant (0.02 M thiourea diluted in $0.4M\;HNO_3$) using 0.01 M TETEDGA as a carrier diluted in n-dodecane. Extraction time was ~160 min. Parameters such as feed acidity, TETEDGA concentration in membrane phase, membrane porosity etc. were optimized to achieve maximum transport rate. Permeability coefficient value of $2.66{\times}10^{-3}cm/s$ was observed using TETEDGA (0.01 M) as carrier, at 3 M, $HNO_3$ feed acidity across $0.2{\mu}m$ PTFE as membrane. The membrane was found to be stable over five runs of the operation.